Parts

TL431 shunt reference

A Zener you set with two resistors: the TL431 holds its REF leg at 2.495 V and sinks whatever cathode current that takes. Aliases: TL431A, KA431, AZ431.

This part has a page of its own, with a note on using it and a circuit to try: the part page.

Tie REF to K and it is a 2.495 V Zener with a fifth of an ohm of dynamic impedance. Put a divider across it, R1 from K to REF and R2 from REF to A, and the cathode settles where REF reaches 2.495 V:

Vka = 2.495 V x (1 + R1 / R2) + 2 uA x R1

Two 10 k resistors make 5.01 V. Feed the cathode from a higher supply through a resistor, as you would a Zener, and give it at least 1 mA.

Pins

Pin What it does
REF The reference input. It draws 2 uA and must not float.
A The anode, normally ground.
K The cathode: the shunt current goes in here.

The legs are drawn where TI's sheet has them on the TO-92 (LP) package: REF A K from the left, flat face toward you. TI numbers them 3 REF, 2 ANODE, 1 CATHODE.

While it runs

The readout is the cathode current, K to A, in milliamps. Under 1 mA it may not be regulating.

What the model gets right

The figures are the typical ones from TI's TL431 sheet (SLVS543S, May 2024), at 25 C.

The reference, 2.495 V at the sheet's test point: REF on K, 10 mA.

The second term. 2 uA flow into REF, so a 10 k R1 adds 20 mV. (The sheet's section 9.2.2.2.1 prints that term with a minus sign; its Figure 7-2 and the physics have it as a plus, and so does the model.)

The cathode's pull on the reference. The reference drops 1.4 mV for every volt on the cathode up to 10 V, and 1 mV a volt from 10 V to 36 V. At 5 V that is 3.5 mV, and the 5 V divider doubles it.

Dynamic impedance, 0.2 ohm from 1 mA to 100 mA, so the cathode moves 9 mV between 5 mA and 50 mA. With a divider it is multiplied by 1 + R1/R2, as the sheet says, because the divider is part of the circuit.

The minimum current. The amplifier needs 0.4 mA of its own (the sheet allows up to 1 mA). Feed it less and the cathode sags under its set voltage.

As a comparator. With no feedback, REF above 2.495 V pulls the cathode down, but only to about 2 V: the output is a Darlington's collector. That is enough for 5 V logic and not for 3.3 V, as the sheet warns. Below 2.495 V it lets go and leaks 0.1 uA.

Backwards, the substrate diode from A to K conducts, about 0.75 V at 10 mA. That figure is assumed: the sheet gives none.

What it does not model

The spread between parts: a real TL431 can sit anywhere from 2.440 V to 2.550 V, the A grade within 1 % and the B grade within 0.5 %, and the model is always the typical 2.495 V. Drift with temperature. The capacitor values that make a real one oscillate (the sheet's stability chart): the model is stable with any capacitor. Its response time and gain roll-off. Damage from more than 100 mA or 37 V.

Common mistakes

No feed resistor. Like a Zener, it shunts: put it straight across a supply and it tries to take amps.

Too little current. A 47 k feed resistor from 12 V gives 0.15 mA, under the minimum, and the output sags.

REF left open. It needs its 2 uA from somewhere: tie it to K or to a divider.

Legs swapped. In the TO-92 the cathode is on the right, not in the middle.

See it in action

TL431 5 V reference sets 5 V with two 10 k resistors and a meter on the cathode. Open it at /templates.