Lessons and the learning game

Troubleshooting control circuits

Find the fault in a motor control circuit like an industrial electrician: the voltage method, hopscotch, coils, overloads, ending in a dead conveyor.

The bench

Every lesson opens the same 24 V DC conveyor starter with a different fault planted. Rung 1 is the control rung: STOP (a lever microswitch on its normally closed contact), START (a push button), the contactor coil K1 and the overload contact, with K1's first contact sealing in across START. Rung 2 feeds the 24 V conveyor motor through K1's second contact. Wire numbers follow the drawing: 1 is L1, 2 is between STOP and START, 3 between START and the coil, 4 between the coil and the overload, 5 and 6 in the motor's rung.

There is no microcontroller: press Run and the simulator solves the circuit. A multimeter stands above the ladder with its leads free, or with the black lead parked on L2 for hopscotch. It updates four times a second, as a real meter does.

Take the course Troubleshooting control circuits on /learn.

Honest stand-ins

  • The overload is two relays standing in for one device. OL1's 1 ohm coil carries the motor current and closes past its setting (1 A from the factory); that pulls in OL2, which latches itself in through a normally closed RESET button and opens the overload contact in rung 1. A small capacitor across OL2's coil gives it the few milliseconds it needs to seal in. A real overload relay is thermal and slow, so it rides through a motor's start; this one is instant, which is why its dial has to sit above the motor's 0.5 A starting current. The Wire, fuses and breakers course has a real inverse-time trip.
  • The burnt contact is a 100 ohm resistor in series with K1's good one.
  • The loose terminal is a slide switch in wire 4.
  • A burnt-open coil is K1 with a coil that never pulls in and reads OL.

One simulator quirk the boss mentions: a wire from a relay's contact straight to that same relay's coil terminal does not hold the relay in. Land the seal-in wire on START's spare leg instead, which is the same net.

The lessons

  1. Reading the ladder: rails, rungs and wire numbers; START, the seal-in and STOP; the coil takes the whole 24 V.
  2. The voltage method: power first, then across each device with START held. Closed contacts read 0 V, the coil reads 0 V, the open reads 24 V.
  3. Hopscotch testing: black on L2, red hopping wire by wire until the voltage vanishes between START and the coil.
  4. Failed coils and contacts: 24 V across a coil that never pulls in, OL on the ohms range and a new 480 ohm coil, then a slow motor and 7.6 V across a burnt contact under load. Welded contacts too.
  5. Overloads: a dial set below the starting current, the running current on a series ammeter (0.075 A), a jam that trips it, and why a trip is a symptom.
  6. Intermittents: why a 10 ms open stops a seal-in circuit for good, the wiggle test with START held, and catching the loose terminal on the meter.
  7. Boss: fix a dead conveyor: an open wire after the coil, a missing seal-in and a jumper across STOP, then a pull-cord stop wired in series.

Safety

Everything in the course is low voltage. Real control panels run 24 V DC or 120 V AC beside motor circuits at 480 V. They are opened only by a qualified person, after lockout/tagout (OSHA 1910.147 in the US), with live testing done under NFPA 70E: the right PPE and a meter rated for the location (CAT III for panels and motor circuits). Prove the meter on a known live source before and after every "dead" reading. Code figures such as NEC 430.32 are informational; local codes and the equipment's instructions govern.

Before and after

The course builds on Relays and motor control (the seal-in), Reading electrical drawings (ladder diagrams), Troubleshooting like a technician (half splitting, opens and shorts) and Electrical safety. The same rung runs in software in PLCs and ladder logic.