All paths

Troubleshooting control circuits

The motor starter an industrial electrician gets called to: read the ladder, find opens with the voltage method and hopscotch, tell coils from contacts, handle overloads and intermittents, and fix a dead conveyor with three faults on it.

Free7 lessons6 h7 chapters2,038 XPElectrical · Advanced+250 XP

0 of 7 done

What you will build

0 projects, built step by step

7 lessons in 7 chapters, about 6 hours on a simulated breadboard. Free, in your browser, every step checked by the simulator.

The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

Reading the ladder

Rails, rungs, wire numbers, and where 24 V should be.

  1. Open265 XP

    Reading the ladder

    A 24 V conveyor starter drawn as a ladder: rails, rungs, wire numbers, a coil and its contacts. Run it, start it, stop it, and read where the voltage sits on each wire.

    0 of 6 steps

4 questions, graded as you go.
Chapter 2

The voltage method

Measure across each device: the open reads the whole supply.

  1. Locked288 XP

    The voltage method

    The conveyor will not start. Measure across each device on the dead rung: closed ones read nothing, the coil reads nothing because no current flows, and the open reads the whole supply.

    0 of 6 steps

4 questions, graded as you go.
Chapter 3

Hopscotch testing

One lead on L2, the other hopping until the voltage vanishes.

  1. Locked288 XP

    Hopscotch testing

    One lead parked on L2, the other hopping from wire number to wire number along the rung. Voltage is there until you jump past the open; then it is gone.

    0 of 6 steps

3 questions, graded as you go.
Chapter 4

Failed coils and contacts

An open coil, a burnt contact under load, and a welded one.

  1. Locked265 XP

    Failed coils and contacts

    A coil with 24 V across it that never pulls in, then a contactor that runs the motor slow: an open coil proved on the ohms range, and a burnt contact found by measuring it under load.

    0 of 6 steps

4 questions, graded as you go.
Chapter 5

Overloads

Read a trip, set the dial from the motor, never reset into a jam.

  1. Locked265 XP

    Overloads

    An overload that trips the instant START is pressed, then a jam that trips it for real. Read the trip, set the dial from the motor's current, measure the running amps, and never reset into a jam.

    0 of 6 steps

4 questions, graded as you go.
Chapter 6

Intermittents

Why a blink is a stop, the wiggle test and the loose terminal.

  1. Locked303 XP

    Intermittents

    A conveyor that stops on its own once a shift and runs fine when you get there. Why a split-second open stops a seal-in circuit for good, the wiggle test, and catching the loose terminal on the meter.

    0 of 7 steps

4 questions, graded as you go.
Chapter 7

Boss: fix a dead conveyor

Three faults, one dangerous, and a pull-cord stop to finish.

  1. Locked364 XP

    Boss: fix a dead conveyor

    A repair ticket on the packing line: the conveyor is dead. Three faults stand between you and a running belt, one of them dangerous. Find each with the meter, fix it, verify, then add a pull-cord stop.

    0 of 8 steps

3 questions, graded as you go.
Syllabus

Every lesson in the course

All 7 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

Reading the ladder

  1. Reading the ladderA 24 V conveyor starter drawn as a ladder: rails, rungs, wire numbers, a coil and its contacts. Run it, start it, stop it, and read where the voltage sits on each wire.
Chapter 2

The voltage method

  1. The voltage methodThe conveyor will not start. Measure across each device on the dead rung: closed ones read nothing, the coil reads nothing because no current flows, and the open reads the whole supply.
Chapter 3

Hopscotch testing

  1. Hopscotch testingOne lead parked on L2, the other hopping from wire number to wire number along the rung. Voltage is there until you jump past the open; then it is gone.
Chapter 4

Failed coils and contacts

  1. Failed coils and contactsA coil with 24 V across it that never pulls in, then a contactor that runs the motor slow: an open coil proved on the ohms range, and a burnt contact found by measuring it under load.
Chapter 5

Overloads

  1. OverloadsAn overload that trips the instant START is pressed, then a jam that trips it for real. Read the trip, set the dial from the motor's current, measure the running amps, and never reset into a jam.
Chapter 6

Intermittents

  1. IntermittentsA conveyor that stops on its own once a shift and runs fine when you get there. Why a split-second open stops a seal-in circuit for good, the wiggle test, and catching the loose terminal on the meter.
Chapter 7

Boss: fix a dead conveyor

  1. Boss: fix a dead conveyorA repair ticket on the packing line: the conveyor is dead. Three faults stand between you and a running belt, one of them dangerous. Find each with the meter, fix it, verify, then add a pull-cord stop.
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About Troubleshooting control circuits

Is Troubleshooting control circuits free?

Yes. All 7 lessons of Troubleshooting control circuits are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need any parts?

No. Every circuit is built on a simulated breadboard, and the simulator checks each step as you go. When you want to build it for real, the same parts and wiring work on a real bench.

How long does Troubleshooting control circuits take?

About 6 hours: 7 lessons in 7 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

Where do I start?

With "Reading the ladder", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.