Kit projects
keyestudio Super Starter Kit: what you can build
Every project in Mokxi that the parts in the keyestudio Super Starter Kit can build, from a first blink up, and the few parts to add for more. Open any of them in the editor with no account.
Not affiliated with keyestudio. Lesson titles are referenced so you can follow along.
Learning path
Everything the keyestudio Super Starter Kit can build
156 projects use only the parts in this box, ordered from a first blink to the hardest.
Beginner (101)
- EEPROM: memory that survives a reset
- Serial echo: the board repeats what you type
- Active buzzer
- Active buzzer module on pin 3
- DHT11 temperature and humidity
- DHT11 module on pin 4
- DHT11 temperature and humidity on pin 10
- DS3231 real-time clock on I2C
- Flame sensor on pin 2 lights the LED on 13
- Gas sensor module on A0
- Joystick on A0, A1 and pin 2
- Joystick module: A0, A1 and pin 3
- Joystick on A0, A1 and pin 8
- LCD1602 on pins 4, 6 and 10 to 13
- LCD1602 on pins 7 to 12
- LCD1602 hello
- LM35 temperature sensor on A0
- Morse code on an active buzzer (pin 9)
- Passive buzzer scale on pin 12
- Passive buzzer module on pin 3
- Passive buzzer on pin 8
- Motion sensor on pin 3 lights the LED on 13
- Motion sensor on pin 12 lights the LED on 13
- Pomodoro timer on an active buzzer (pin 9)
- RC522 RFID reader (SS 10, RST 9)
- Servo sweep
- Servo sweep on pin 10
- Servo sweep on pin 3
- Siren on a passive buzzer (pin 9)
- Ultrasonic distance on pins 12 and 11
- Ultrasonic sensor on 8 and 7, the LED on 13 when out of range
- Stepper motor on pins 8 to 11
- Twinkle, Twinkle, Little Star on a passive buzzer (pin 9)
- Read a knob
- Digital piano
- Fade an LED
- First blink
- IR decoder
- Blink an LED on pin 13, once a second
- Blink an LED on pin 3
- Blink an LED on pin 8
- Blink an LED on pin 9
- Breathing LED on pin 5
- Button on pin 12 lights the LED on pin 13
- Answer ball
- Flowing lights on pins 2 to 9
- IR remote codes on pin 12
- IR receiver module on pin 11
- IR receiver on pin 2
- LED module on pin 7, blinking
- An LED on the 5 V pin
- Mood dial
- Four brightnesses from PWM: pins 5, 6, 9 and 10
- RGB colors on pins 11, 10 and 9
- RGB LED on pins 3, 5 and 6
- RGB fade on pins 6, 5 and 3
- RGB LED module: red 11, blue 10, green 9
- Random colors on an RGB LED (pins 11, 10 and 9)
- Set the LED on pin 11 from the serial monitor
- A knob on A0 points the servo on pin 3
- Seven-segment digit on pins 4 to 11
- Tilt switch on pin 3 lights the LED on 13
- Traffic lights on pins 3, 4 and 5
- Two LEDs take turns on pins 4 and 5
- RGB color mixer
- Arduino Uno blink
- Button and LED
- Grabbing candy bowl
- Push button on pin 12 lights the LED on pin 9
- A push button lights an LED, no code
- Push button on pin 12 toggles the LED on pin 9
- Dinosaur game player: light sensor on A0, servo on 9
- Doorbell: button on pin 2, buzzer on pin 8
- Tilt hourglass
- Remote control light switch (IR on 12, servo on 11)
- Joystick lights the way (LEDs on 8 to 11)
- Four-key keyboard
- Knob on A0 dims the LED on pin 9
- Photoresistor night light: A0 dims the LED on pin 9
- Light meter: photoresistor on A0, LEDs on pins 5 to 12
- PIR motion light
- Motion night light (PIR on 12, RGB on 5, 6 and 9)
- Relay module on pin 8
- Three knobs mix an RGB LED (pins 11, 10 and 9)
- Starship control panel
- Tilt switch on A5 lights the LED on pin 8
- Tilt switch
- Traffic lights with a crossing button on pin 8
- Two buttons, one LED
- Warm or cool light: a knob blends an RGB LED
- Night light
- Ofrenda candles
- Piezo melody
- Dimmer
- Night light with a light sensor
- Fog machine trigger
- A button doorbell with a lamp, no code
- On and off desk lamp: button on 7, relay on 2
- Metronome
- Police lights and siren
- Rescue beacon
Intermediate (50)
- Two Arduino Unos talking over serial
- ADXL345 accelerometer on I2C
- DHT11 on A0, read with no library
- LCD1602 in 8-bit mode on pins 2 to 12
- Tilt level
- DHT11 on pin 3, readings on an LCD
- Radar sweep: ultrasonic on 10 and 11, servo on 12
- Smart trash can: ultrasonic on 8 and 7, servo lid on 9
- Ultrasonic distance on an LCD (TRIG 2, ECHO 3)
- Stepper follows a knob (pins 2 to 5)
- Stepper turntable
- Arpeggiator
- LED bar chaser
- Electronic dice
- Joystick bar graph
- Hex digits on a common-anode display (74HC595, pins 11, 12, 13)
- Countdown digit
- Hex digits through a 74HC595 (pins 11, 8 and 12)
- One-digit countdown on a 74HC595 (pins 2, 4 and 3)
- One-digit countdown on a 74HC595 (pins 8, 10 and 9)
- Falling rain on eight LEDs (74HC595, pins 11, 12 and 13)
- Flowing light on a 74HC595 (pins 11, 8 and 12)
- Eight LEDs on a 74HC595 (pins 12, 9 and 11)
- Eight LEDs on a 74HC595 (pins 2, 5 and 4)
- A light runs along eight LEDs on a 74HC595 (pins 11, 12 and 13)
- Serial monitor drives eight LEDs (74HC595)
- Type a digit: serial to a 74HC595 display (pins 11, 8 and 12)
- Cyber dice: seven-segment on pins 2 to 8, button on 9
- Four-digit display on a 74HC595 (pins 8, 10 and 9)
- Ultrasonic ranging on an LCD
- Remote stepper
- Remote stepper, a whole turn a press
- RFID door
- Remote-controlled lamps
- Photocell bar graph on a 74HC595
- Photoresistor bar graph on a 74HC595 (pins 9, 12 and 11)
- Digital dice on a 74HC595 (pins 11, 8 and 12)
- Remote-controlled colors: IR on pin 2, RGB on 11, 10 and 9
- Photocell light meter
- Quiz buzzer for three players
- Looper
- Servo turnouts with a panel
- Reaction duel
- Parking sensor
- Tap-tempo metronome
- ADSR synth
- Reaction timer
- Ringtone player
- Memory math game on an LCD and an IR remote
- Lion dance head
Level up
Add a few parts, unlock more projects
The smallest shopping lists that open the most new projects for the keyestudio Super Starter Kit.
Add Character LCD with I2C backpack
Unlocks 16 more projects:
Add Character LCD with I2C backpack and Addressable RGB LEDs
Unlocks 29 more projects:
Add ili9341, Character LCD with I2C backpack and Addressable RGB LEDs
Unlocks 41 more projects:
Two kits
Projects that combine two kits
Own another kit as well? These need parts from both boxes, and neither can build them alone.
In the box
The kit’s parts, and what plays them here
The parts in the keyestudio Super Starter Kit, by the names its maker gives them. Each one is in the editor’s parts panel.
- KEYESTUDIO R3 board Arduino Uno R3 An Uno R3 compatible board, named on the KS0078 store page; the docs call it the V4.0 board. KS0077 has no board, and KS0079 has a Mega 2560.
- 830-hole Breadboard Full-size breadboard
- LED - Blue, LED - Red and LED - Yellow LED
- LED - RGB RGB LED
- 220 ohm, 10K ohm and 1K ohm resistors Resistor
- 10K ohm Potentiometer Potentiometer
- Buzzer (Active) Buzzer
- Buzzer (Passive) Piezo speaker
- Large Button Switch Pushbutton
- Ball Tilt Sensor Tilt switch
- Photo Resistor Light sensor
- Flame Sensor Flame sensor The kit’s is a bare sensor wired with a 10k resistor; the Mokxi part is a module, read on its AO pin.
- LM35 Temp Sensor Temperature sensor, LM35
- IC 74HC595N 16-pin DIP 74HC595 shift register
- 7-seg LED Segment Display (1 digit) Seven segment display
- 7-seg LED Segment Display (4 digits) Four-digit seven segment, multiplexed
- 8*8 LED Matrix Not simulated yet; the MAX7219 matrix module is.
- 2x16 LCD display Character LCD, 16x2
- IR Receiver Infrared receiver, VS1838B
- IR Remote Control Infrared remote, 21 buttons
- Servo Motor Hobby servo
- Stepper Motor and Stepper Driver Stepper motor, 28BYJ-48 with ULN2003
- Joystick Module Thumb stick
- Relay Module Relay module
- PIR Motion Sensor Motion sensor
- Analog Gas Sensor Gas sensor, MQ-2
- ADXL345 Three Axis Acceleration Module Accelerometer, ADXL345
- HC-SR04 Ultrasonic Sensor Ultrasonic ranger
- DS3231 Clock Module Real-time clock, DS3231
- DHT11 Temperature and Humidity Sensor Temperature and humidity, DHT22 Set to the DHT11 model on the canvas.
- Soil Humidity Sensor Soil moisture sensor, resistive FC-28
- RC522 RFID Module, RFID Card and Access Key RFID reader, MFRC522 Its cards are on the part: click one onto the reader.
- 6-Slot AA Battery Holder Battery: AA, coin cell, LiPo Set to six AA cells.
- Pin Headers Header pins for soldering; nothing to place.
- USB Cable The editor connects the board for you.
- Dupont Wire and Jumper Wire Drawn as wires between pins; nothing to place.
Parts list read from keyestudio’s Super Learning Kit docs. An item with no part beside it has no match in the editor yet.
For the manual
A link and a QR code for this page
Print either one beside a lesson, or tape it inside the box lid. Both open this page.
mokxi.com/k/keyestudio-super-starter
The code is black on white with a quiet border, so it prints and scans at any size from 2 cm up.
Download the QR code (SVG)Make kits? See what we offer kit makers.
FAQ
Questions about this page
Is this made by keyestudio?
No. Mokxi is independent and is not affiliated with keyestudio. The page follows the kit’s lessons so you can use the two side by side; the circuits, sketches and explanations are Mokxi’s own.
Do I need the kit?
No. Every lesson that runs here runs in the browser, so you can try them before you buy a kit, or keep going while a part is missing or broken.
Is the code the same as in my manual?
The pins and the parts are the same, and the sketches use the same libraries where the kit does. The code itself is written for this page, with comments that explain each step, so it will not match the manual line for line.
What do "with a change" and "coming soon" mean?
A lesson marked "with a change" runs, but something differs from the kit, and the note under it says exactly what. "Coming soon" means we cannot simulate that lesson yet, and the note says why. We do not mark a lesson as running unless it does.
Is it free?
Yes. Every lesson on this page opens with no account. A free account saves your own copies of the circuits.
Keep going
Other kits
Companion pages for more starter kits.
ELEGOO UNO R3 Super Starter Kit
25 lessons, 24 run in the browser
ELEGOO UNO R3 Most Complete Starter Kit
48 lessons, 44 run in the browser
Arduino Starter Kit
15 lessons, 15 run in the browser
Freenove Ultimate Starter Kit
42 lessons, 42 run in the browser
ELEGOO UNO R3 Basic Starter Kit
11 lessons, 10 run in the browser
SunFounder Starter Kit for Arduino Uno R3
23 lessons, 23 run in the browser
SunFounder Inventor Lab Kit
34 lessons, 33 run in the browser
Keyestudio 37 in 1 Sensor Kit
37 lessons, 37 run in the browser
REXQualis UNO R3 Super Starter Kit
22 lessons, 21 run in the browser
LAFVIN Super Starter Kit
28 lessons, 27 run in the browser
Freenove Ultimate Starter Kit for ESP32-WROVER
54 lessons, 44 run in the browser
SunFounder Kepler Kit for Raspberry Pi Pico W
63 lessons, 48 run in the browser
Freenove Ultimate Starter Kit for Raspberry Pi Pico
56 lessons, 50 run in the browser
Vilros Arduino Uno 3 Ultimate Starter Kit
Projects you can build with its parts
SunFounder Universal Maker Sensor Kit
Projects you can build with its parts
SunFounder ESP32 Ultimate Starter Kit
Projects you can build with its parts
Adafruit MetroX Classic Kit
Projects you can build with its parts
MonkMakes Electronics Kit 1 for Raspberry Pi Pico
Projects you can build with its parts
Kitronik Discovery Kit for Raspberry Pi Pico
Projects you can build with its parts
Kitronik Inventor’s Kit for the Raspberry Pi Pico
Projects you can build with its parts
Keyestudio ESP32 Learning Kit Ultimate Edition
Projects you can build with its parts
Start with the first project
Every project opens in the editor with no account and nothing to install. Run it, change a number, run it again.