Music and sound

Arduino music and sound projects

These projects are tagged sound or synth. Buzzers and piezos play tunes, and there are alarms, drum pads, theremins and synths. Mokxi has 126 of them (39 beginner, 55 intermediate and 32 advanced). Here are 24, from “MicroPython doorbell: a button sounds a buzzer” to “Eurorack CV quantizer”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

How to pick your first one

  • Start with “Touch piano”, a beginner project that needs a capacitive touch and a piezo speaker.
  • Most of them are intermediate projects. Pick one a level below what you think you can do, finish it, then move up.
  • The parts used most here are the piezo speaker (76 projects), the push button (57) and the LED (41). With those on hand, most of this list is open to you.
  • A passive piezo plays any note with tone(); an active buzzer only beeps at its own pitch, so check which one a project uses before you buy.
Projects

24 projects of 126

  • MicroPython doorbell: a button sounds a buzzer, drawn in the Mokxi editor

    MicroPython doorbell: a button sounds a buzzer

    MicroPython on an ESP32: hold the button on GPIO 4 and an active buzzer, switched through an S8050 transistor from GPIO 13, sounds.

    Board
    ESP32-DevKitC V4
    Parts
    Buzzer, resistor, transistor, push button
    Level
    Beginner
    Open in the simulator
  • Ultrasonic theremin, drawn in the Mokxi editor

    Ultrasonic theremin

    Ultrasonic theremin on an Arduino Nano: wave a hand over an HC-SR04 to play notes of a pentatonic scale, or glide the pitch like a real theremin.

    Board
    Arduino Nano
    Parts
    HC-SR04 ultrasonic sensor, arcade button, piezo speaker
    Level
    Beginner
    Open in the simulator
  • Morse sender, drawn in the Mokxi editor

    Morse sender

    An ESP32-C3 sends a word in Morse on a lamp and a piezo at once, and a button picks the next message.

    Board
    ESP32-C3-DevKitM-1
    Parts
    Resistor, LED, piezo speaker, push button
    Level
    Beginner
    Open in the simulator
  • Doorbell, drawn in the Mokxi editor

    Doorbell

    A pushbutton lifts the 555 out of reset and a 4 Hz astable beeps the buzzer.

    Board
    No board
    Parts
    Resistor, NE555 timer, capacitor, push button, buzzer
    Level
    Beginner
    Open in the simulator
  • Stop the light game, drawn in the Mokxi editor

    Stop the light game

    Stop the light game on a Raspberry Pi Pico: press the button as a red light runs onto the green LED of a 16-LED NeoPixel ring, faster every level.

    Board
    Raspberry Pi Pico
    Parts
    WS2812 NeoPixel LEDs, arcade button, piezo speaker
    Level
    Beginner
    Open in the simulator
  • Touch piano, drawn in the Mokxi editor

    Touch piano

    Twelve foil keys on an MPR121 touch controller play an octave from middle C on a piezo; the lowest key held wins.

    Board
    Arduino Uno R3
    Parts
    Capacitive touch, piezo speaker
    Level
    Beginner
    Open in the simulator
  • Vibration alarm: a spring switch on pin 3, a buzzer on 13, drawn in the Mokxi editor

    Vibration alarm: a spring switch on pin 3, a buzzer on 13

    A spring vibration switch from pin 3 to ground fires an interrupt the moment it is shaken, and an active buzzer on pin 13.

    Board
    Arduino Uno R3
    Parts
    Resistor, transistor, buzzer, spring vibration switch
    Level
    Beginner
    Open in the simulator
  • LED fireworks, drawn in the Mokxi editor

    LED fireworks

    Rockets climb a 30-LED WS2812B strip and burst into fading sparks while a piezo whistles and pops, with a button for the grand finale.

    Board
    Arduino Uno R3
    Parts
    Push button, resistor, WS2812 NeoPixel LEDs, piezo speaker
    Level
    Intermediate
    Open in the simulator
  • ESP32 I2S sine player, drawn in the Mokxi editor

    ESP32 I2S sine player

    A MAX98357A I2S amplifier on an ESP32 playing a 440 Hz sine into a speaker, the samples computed in the sketch with ESP_I2S.h.

    Board
    ESP32 DevKit V1
    Parts
    I2S amplifier, 8 ohm speaker
    Level
    Intermediate
    Open in the simulator
  • Animated diorama: DFPlayer sound + stepper, drawn in the Mokxi editor

    Animated diorama: DFPlayer sound + stepper

    A button plays a C-3PO line on a DFPlayer Mini while a 28BYJ-48 turns R2-D2’s dome.

    Board
    Arduino Nano
    Parts
    DFPlayer Mini MP3 module, resistor, push button, 8 ohm speaker, 28BYJ-48 stepper and ULN2003
    Level
    Intermediate
    Open in the simulator
  • Pico W reversing aid: HC-SR04 and a beeper, drawn in the Mokxi editor

    Pico W reversing aid: HC-SR04 and a beeper

    MicroPython on a Pico W: an HC-SR04 on GP17 and GP16 measures the gap, and an active buzzer and an LED beep faster as an obstacle gets closer.

    Board
    Raspberry Pi Pico W
    Parts
    HC-SR04 ultrasonic sensor, resistor, buzzer, transistor, LED
    Level
    Intermediate
    Open in the simulator
  • Jukebox, drawn in the Mokxi editor

    Jukebox

    A DFPlayer Mini over SoftwareSerial with DFRobot’s library: it plays the microSD card’s files one after another, hears each one end, and watches BUSY.

    Board
    Arduino Uno R3
    Parts
    DFPlayer Mini MP3 module, resistor
    Level
    Intermediate
    Open in the simulator
  • 555 tone, drawn in the Mokxi editor

    555 tone

    A 555 astable drives a piezo straight from the output pin, no board and no button.

    Board
    No board
    Parts
    Resistor, NE555 timer, capacitor, piezo speaker
    Level
    Intermediate
    Open in the simulator
  • DAC sine wave, drawn in the Mokxi editor

    DAC sine wave

    An MCP4725 on I2C plays a 32-point sine onto a scope: a real voltage, not PWM, and A0 reads it back to check.

    Board
    Arduino Uno R3
    Parts
    DAC, oscilloscope
    Level
    Intermediate
    Open in the simulator
  • ESP32 I2S microphone level meter, drawn in the Mokxi editor

    ESP32 I2S microphone level meter

    An INMP441 I2S microphone on an ESP32, read with the ESP-IDF I2S driver: the sound level in dBFS and a bar on the serial monitor.

    Board
    ESP32 DevKit V1
    Parts
    I2S microphone
    Level
    Intermediate
    Open in the simulator
  • Handheld game console, drawn in the Mokxi editor

    Handheld game console

    A pocket console you can build: an ESP32-C3, a color TFT, a D-pad, A, B, Start and Select, chiptune on a piezo and a battery gauge.

    Board
    ESP32-C3-DevKitM-1
    Parts
    ILI9341 TFT display, game console buttons, piezo speaker, push button, battery: AA, +1 more
    Level
    Advanced
    Open in the simulator
  • MIDI controller, drawn in the Mokxi editor

    MIDI controller

    Two faders, a knob, four drum pads and an encoder on a Pro Micro, sending real MIDI bytes the 5-pin way.

    Board
    SparkFun Pro Micro
    Parts
    Resistor, LED, slide potentiometer, push button, potentiometer, +1 more
    Level
    Advanced
    Open in the simulator
  • Alarm clock with a timer on a four-digit display, drawn in the Mokxi editor

    Alarm clock with a timer on a four-digit display

    A DS1307 keeps the time on a four-digit display driven by a 74HC595 (8, 13, 12).

    Board
    Arduino Uno R3
    Parts
    74HC595 shift register, four-digit seven-segment display, resistor, push button, RGB LED, +3 more
    Level
    Advanced
    Open in the simulator
  • Slot machine, drawn in the Mokxi editor

    Slot machine

    Pull a real arcade lever to spin three OLED reels that stop one by one. Coins, a bet, win lights and a pay table with odds you can check.

    Board
    Arduino Uno R3
    Parts
    Piezo speaker, WS2812 NeoPixel LEDs, arcade button, arcade joystick lever, SSD1306 OLED display
    Level
    Advanced
    Open in the simulator
  • Breakout game on an OLED, drawn in the Mokxi editor

    Breakout game on an OLED

    Breakout game on an OLED with a knob for the paddle: 32 bricks, three lives, a faster ball for every wall you clear, and sound on a piezo.

    Board
    Arduino Mega 2560 R3
    Parts
    SSD1306 OLED display, arcade button, piezo speaker, potentiometer
    Level
    Advanced
    Open in the simulator
  • Desk buddy robot, drawn in the Mokxi editor

    Desk buddy robot

    Animated robot eyes on a round GC9A01: it blinks and glances about, beams when you stroke it, gets dizzy when rocked and lonely when ignored.

    Board
    ESP32-C3-DevKitM-1
    Parts
    GC9A01 round display, MPU6050 accelerometer and gyro, touch sensor, photoresistor module, piezo speaker
    Level
    Advanced
    Open in the simulator
  • Spaceship control panel, drawn in the Mokxi editor

    Spaceship control panel

    Arm three systems, pass the go/no-go poll, lift the safety and launch.

    Board
    Arduino Mega 2560 R3
    Parts
    Slide switch, LED arcade button, TM1637 four-digit display, piezo speaker, WS2812 NeoPixel LEDs, +7 more
    Level
    Advanced
    Open in the simulator
  • Pinball table, drawn in the Mokxi editor

    Pinball table

    A table you can play on a Mega: flippers, pop bumpers on a kicker solenoid, targets, a drain beam and a plunger, with a four-digit score.

    Board
    Arduino Mega 2560 R3
    Parts
    TM1637 four-digit display, WS2812 NeoPixel LEDs, pinball table, MOSFET, diode, +3 more
    Level
    Advanced
    Open in the simulator
  • Eurorack CV quantizer, drawn in the Mokxi editor

    Eurorack CV quantizer

    A control voltage snapped to the nearest note of a scale and sent out at one volt per octave through a filtered PWM DAC.

    Board
    Arduino Nano
    Parts
    Potentiometer, resistor, capacitor, LED, slide switch, +2 more
    Level
    Advanced
    Open in the simulator

See all 126 music and sound projects on the templates page