Project ideas by part

LED projects for Arduino, ESP32 and Pico

278 Mokxi projects use an LED (141 beginner, 100 intermediate and 37 advanced). They run on Arduino Uno and ESP32 boards, and 32 need no board at all. Here are 24, from “Relay module on pin 8” to “An ESP32 and an Arduino Uno talking over serial”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

How to pick your first one

  • Start with “Blink, with a breakpoint”, a beginner project that needs a resistor and an LED.
  • Arduino Uno runs 142 of them, ESP32 43 and 32 need no board at all. Start on the board you have, or on an Arduino Uno if you are buying one.
  • The parts used most here are the push button (89 projects), the potentiometer (38) and the piezo speaker (31). With those on hand, most of this list is open to you.
  • Before you build one on a real bench, read the LED wiring guide for your board below. It gives every pin and the voltage notes.
Projects

24 projects of 278

  • Relay module on pin 8, drawn in the Mokxi editor

    Relay module on pin 8

    A relay module on pin 8 clicks on and off every two seconds; its contact switches an LED.

    Board
    Arduino Uno R3
    Parts
    Resistor, LED, relay module
    Level
    Beginner
    Open in the simulator
  • ESP32-C3 PWM fade, drawn in the Mokxi editor

    ESP32-C3 PWM fade

    Breathes an LED on GPIO 4 and the on-board one on GPIO 8 with analogWrite.

    Board
    ESP32-C3-DevKitM-1
    Parts
    Resistor, LED
    Level
    Beginner
    Open in the simulator
  • Pico W chaser, drawn in the Mokxi editor

    Pico W chaser

    Six lamps sweeping on the breadboard, on the same pins as the Pico’s chaser.

    Board
    Raspberry Pi Pico W
    Parts
    Resistor, LED
    Level
    Beginner
    Open in the simulator
  • STM32 chaser, drawn in the Mokxi editor

    STM32 chaser

    A six-LED sweep that runs back and forth on the Black Pill, wired to PA1 through PA6.

    Board
    STM32F411 Black Pill
    Parts
    Resistor, LED
    Level
    Beginner
    Open in the simulator
  • ESP-01 blink, drawn in the Mokxi editor

    ESP-01 blink

    An LED wired from 3V3 through a resistor to GPIO 2 lights together with the module’s own blue one, whenever the pin goes low.

    Board
    ESP-01S
    Parts
    LED, resistor
    Level
    Beginner
    Open in the simulator
  • NodeMCU fade, drawn in the Mokxi editor

    NodeMCU fade

    An LED breathing on an ESP8266, which has no PWM hardware at all: the core moves the pin itself, and the range is 0 to 1023.

    Board
    ESP8266 NodeMCU V1.0
    Parts
    Resistor, LED
    Level
    Beginner
    Open in the simulator
  • MicroPython motion sensor on a Pico: PIR on GP18, LED, drawn in the Mokxi editor

    MicroPython motion sensor on a Pico: PIR on GP18, LED

    MicroPython on a Raspberry Pi Pico: an HC-SR501 motion sensor on GP18 lights the LED on GP15 for as long as its output says something moved.

    Board
    Raspberry Pi Pico
    Parts
    PIR motion sensor, resistor, LED
    Level
    Beginner
    Open in the simulator
  • ESP32 web server with two LEDs, drawn in the Mokxi editor

    ESP32 web server with two LEDs

    The Random Nerd Tutorials ESP32 web server: press Run, open the Web panel, and its ON and OFF buttons switch the LEDs on GPIO 26 and 27.

    Board
    ESP32 DevKit V1
    Parts
    Resistor, LED
    Level
    Beginner
    Open in the simulator
  • Uno R4 knob, drawn in the Mokxi editor

    Uno R4 knob

    A potentiometer on an Uno R4’s A0 fades an LED on pin 9, and the monitor prints the same pin in ten bits and in the converter’s own fourteen.

    Board
    Arduino Uno R4 Minima
    Parts
    Potentiometer, resistor, LED
    Level
    Beginner
    Open in the simulator
  • Nucleo blink, drawn in the Mokxi editor

    Nucleo blink

    The STM32 Nucleo-F411RE’s green LED on D13 and an LED beside the board, which light when the pin is HIGH, as on an Uno.

    Board
    STM32 Nucleo-F411RE
    Parts
    Resistor, LED
    Level
    Beginner
    Open in the simulator
  • Leonardo fade, drawn in the Mokxi editor

    Leonardo fade

    Two LEDs off two different kinds of timer: the ten-bit one on pin 13 and an ordinary 16-bit one on pin 9.

    Board
    Arduino Leonardo
    Parts
    Resistor, LED
    Level
    Beginner
    Open in the simulator
  • Dimmer, drawn in the Mokxi editor

    Dimmer

    A potentiometer on A0 sets the brightness of an LED on pin 9. Turn the knob while it runs.

    Board
    Arduino Uno R3
    Parts
    Potentiometer, resistor, LED
    Level
    Beginner
    Open in the simulator
  • RP2040-Zero blink, drawn in the Mokxi editor

    RP2040-Zero blink

    An LED on GP0 of the RP2040-Zero, which has no plain LED of its own, with the board beside the breadboard.

    Board
    Waveshare RP2040-Zero
    Parts
    Resistor, LED
    Level
    Beginner
    Open in the simulator
  • XIAO S3 knob, drawn in the Mokxi editor

    XIAO S3 knob

    The XIAO knob circuit on the ESP32-S3: D0 is A0 on GPIO 1, and the count is printed as the converter gives it.

    Board
    Seeed XIAO ESP32-S3
    Parts
    Potentiometer, resistor, LED
    Level
    Beginner
    Open in the simulator
  • SuperMini blink, drawn in the Mokxi editor

    SuperMini blink

    The blue LED on GPIO 8 lights when the pin is low and an LED on GPIO 2 when it is high, on the smallest ESP32-C3 board.

    Board
    ESP32-C3 SuperMini
    Parts
    Resistor, LED
    Level
    Beginner
    Open in the simulator
  • A button toggles an LED with gpiozero, drawn in the Mokxi editor

    A button toggles an LED with gpiozero

    gpiozero on a Raspberry Pi 4: each press of a button on GPIO2 turns the LED on GPIO17 on or off, with when_pressed and signal.pause().

    Board
    Raspberry Pi 4 Model B
    Parts
    Resistor, LED, push button
    Level
    Beginner
    Open in the simulator
  • Blue Pill lamp, drawn in the Mokxi editor

    Blue Pill lamp

    A lamp on a Blue Pill that blinks in step with the board’s own LED, because both hang off 3.3 V and PC13 sinks them.

    Board
    STM32 Blue Pill (F103)
    Parts
    Resistor, LED
    Level
    Beginner
    Open in the simulator
  • ATmega328P at 8 MHz, drawn in the Mokxi editor

    ATmega328P at 8 MHz

    An ATmega328P in a breadboard on its internal 8 MHz clock, with no crystal, running a blink built for 8 MHz.

    Board
    ATmega328P, 8 MHz internal clock
    Parts
    ATmega328P, resistor, LED
    Level
    Beginner
    Open in the simulator
  • Night light with a light sensor, drawn in the Mokxi editor

    Night light with a light sensor

    A light-dependent resistor in a divider fades a lamp up when the room goes dark. Drag the slider on the sensor.

    Board
    Arduino Uno R3
    Parts
    Photoresistor, resistor, LED
    Level
    Beginner
    Open in the simulator
  • Nano dial, drawn in the Mokxi editor

    Nano dial

    A potentiometer on the Nano's A7, the analog-only pin an Uno does not have, fades an LED on pin 9.

    Board
    Arduino Nano
    Parts
    Potentiometer, resistor, LED
    Level
    Beginner
    Open in the simulator
  • Blink, with a breakpoint, drawn in the Mokxi editor

    Blink, with a breakpoint

    Stop the board on the line that lights the LED, and see it frozen mid-blink with its registers.

    Board
    ESP32-C3-DevKitM-1
    Parts
    Resistor, LED
    Level
    Beginner
    Open in the simulator
  • Dance pad on a Pro Micro, drawn in the Mokxi editor

    Dance pad on a Pro Micro

    Four FSR panels on A0 to A3 with a press and a release threshold each, lighting a panel lamp and sent as four gamepad buttons through Joystick.h.

    Board
    SparkFun Pro Micro
    Parts
    Force-sensing resistor, LED, resistor
    Level
    Intermediate
    Open in the simulator
  • HC-SR04 distance sensor with gpiozero, drawn in the Mokxi editor

    HC-SR04 distance sensor with gpiozero

    gpiozero DistanceSensor on a Raspberry Pi 5: an HC-SR04 with its echo divided down to 3.3 V.

    Board
    Raspberry Pi 5
    Parts
    HC-SR04 ultrasonic sensor, resistor, LED
    Level
    Intermediate
    Open in the simulator
  • An ESP32 and an Arduino Uno talking over serial, drawn in the Mokxi editor

    An ESP32 and an Arduino Uno talking over serial

    An ESP32 reads a knob and sends the number to an Arduino Uno over a serial wire; the Uno sets an LED’s brightness from it.

    Board
    ESP32 DevKit V1 and Arduino Uno R3
    Parts
    Potentiometer, resistor, LED
    Level
    Intermediate
    Open in the simulator