Wiring guide

How to wire a buzzer to an Arduino Nano

To wire a buzzer to an Arduino Nano, connect 1 to pin 8 and 2 to GND. A small passive piezo draws a few milliamps, so it runs straight from the pin with its other leg on ground. The sketch below uses no library beyond what the board includes. It plays a four-note phrase and repeats it, printing Playing once and Again after each phrase.

  • 5 V logic
  • Library: none
  • 2 wires
Arduino Nano · buzzerlive0.000 s 0.00x
Click to open it in the editor
The circuit itself, running on the simulator with the sketch below. Press what can be pressed; click anything else to open it in the editor.
Pin to pin

Buzzer to Arduino Nano wiring table

Every wire in the circuit above, with the part’s pin names and the board’s own labels. The wire colors are the ones the circuit uses; on a real bench any colors work.

Buzzer pinArduino Nano pinWire colorWhy
Pin 1pin 8ambertone() puts a square wave at the note’s frequency on this pin.
Pin 2GNDblueGround. A passive piezo has no polarity.
Voltage

Power and logic levels for buzzer and Arduino Nano

Logic level

The Arduino Nano’s pins are 5 V logic. A 5 V part can drive them directly; a part whose signal pins are limited to 3.3 V needs a level shifter.

This pair

A small passive piezo draws a few milliamps and runs straight from the pin. On the ATmega328P, tone() takes Timer2, so PWM on pins 3 and 11 pauses while a note plays.

Pins to leave alone

A6 and A7 are analog only: pinMode(A6, OUTPUT) does nothing and digitalRead(A7) is not there to call. D0 and D1 are the USB serial port.

The sketch

The working code for the Arduino Nano

Library: none, the sketch makes the note with tone(). This is the sketch the circuit above runs.

Tones on Arduino Nano pin 8
const int BUZZER_PIN = 8;   // pin 8

// C, E, G, C: an arpeggio, a quarter second a note.
const int NOTES[] = {523, 659, 784, 1047};

void setup() {
  Serial.begin(9600);
  Serial.println("Playing");
}

void loop() {
  for (int i = 0; i < 4; i++) {
    tone(BUZZER_PIN, NOTES[i], 200);   // returns at once; the note plays on
    delay(250);
  }
  noTone(BUZZER_PIN);
  Serial.println("Again");
  delay(500);
}
Output

What you should see

The buzzer plays a short four-note phrase and then plays it again. The serial monitor, at 9600 baud, prints Playing at the start and Again after each phrase.

A buzzer that clicks once but never sounds a note is an active buzzer: it ignores tone() and needs only a HIGH level.

The serial monitor prints this, recorded from the circuit above running for two seconds:

Playing
Again
Pitfalls

Common mistakes wiring a buzzer to an Arduino Nano

An active buzzer

An active buzzer has its own oscillator and beeps at one pitch whenever it has power, so tone() cannot change its note. For melodies you need a passive one; the two look the same, but the active kind usually has a sticker on top.

No delay between notes

tone() does not wait for the note to finish. Call it twice in a row and only the second note plays. Wait at least as long as the note, as the sketch does.

Picking A6 or A7

A6 and A7 look like the other analog pins but are inputs to the ADC and nothing else. the buzzer on either of them never sees a digital level. Any of D2 to D13 or A0 to A5 works.

Build your own buzzer project

Open this circuit in the editor, change the wiring or the code, and keep your version in a free account.