Weather station projects
These are the weather stations, barometers, thermometers and rain gauges named for what they measure, and every project built on a BME280. Mokxi has 30 of them (10 beginner, 19 intermediate and 1 advanced). Here are 24, from “NTC thermometer” to “LoRa weather station with acknowledgments”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.
How to pick your first one
- Start with “CircuitPython BME280 on a Pico”, a beginner project that needs a BME280 sensor.
- Most of them are intermediate projects. Pick one a level below what you think you can do, finish it, then move up.
- The parts used most here are the BME280 weather sensor (7 projects), the I2C LCD (7) and the 10k NTC thermistor (7). With those on hand, most of this list is open to you.
- Read one sensor and print it to the serial monitor before you add a display or WiFi; a reading that is wrong on serial will be wrong everywhere else too.
24 projects of 30

NTC thermometer
The NTC temperature sensor module on A0, worked out in degrees with the beta equation every tutorial for it uses.
- Board
- Arduino Uno R3
- Parts
- NTC temperature sensor module
- Level
- Beginner

CircuitPython BME280 on a Pico
CircuitPython on a Raspberry Pi Pico: busio.I2C and Adafruit’s adafruit_bme280 read the temperature.
- Board
- Raspberry Pi Pico
- Parts
- BME280 weather sensor
- Level
- Beginner

DHT11 temperature and humidity
A DHT11 module on pin 2: the DHT library reads the temperature and humidity every two seconds and prints both.
- Board
- Arduino Uno R3
- Parts
- DHT11 or DHT22 sensor
- Level
- Beginner

Pico W DHT11 temperature and humidity on GP16
MicroPython on a Pico W: the dht module reads a DHT11 on GP16 and prints the temperature and humidity every two seconds, retrying a failed read.
- Board
- Raspberry Pi Pico W
- Parts
- DHT11 or DHT22 sensor
- Level
- Beginner

Fever thermometer
An MLX90614 reads a forehead without touching it; an I2C LCD shows the temperature, and over 38 C it says FEVER and beeps.
- Board
- Arduino Uno R3
- Parts
- IR thermometer, I2C LCD, piezo speaker
- Level
- Beginner

Pico W thermistor thermometer on GP28
MicroPython on a Pico W: a 10k thermistor divider on GP28, its resistance turned into Celsius and Fahrenheit with the beta equation, once a second.
- Board
- Raspberry Pi Pico W
- Parts
- Resistor, 10k NTC thermistor
- Level
- Beginner

MicroPython BME280 weather on an OLED
MicroPython on a Raspberry Pi Pico: machine.I2C reads a BME280 and shows temperature, pressure and humidity on an SSD1306 OLED with ssd1306.py.
- Board
- Raspberry Pi Pico
- Parts
- SSD1306 OLED display, BME280 weather sensor
- Level
- Intermediate

WiFi: fetch the weather
HTTPClient against a simulated origin, with the numbers on a dial in the Cloud panel, and a request to the real internet that is refused.
- Board
- ESP32-C3-DevKitM-1
- Parts
- Just the board
- Level
- Intermediate

Indoor and outdoor thermometer on two OLEDs
Two BME280s and two SSD1306 OLEDs share their addresses, so a TCA9548A puts each pair on its own channel: each screen shows its own weather.
- Board
- Arduino Uno R3
- Parts
- I2C multiplexer, BME280 weather sensor, SSD1306 OLED display
- Level
- Intermediate

ESP32 DHT22 weather web server
ESP32 DHT22 weather web server: the board serves its own page with the temperature in C and F and the humidity, plus the same reading as JSON.
- Board
- ESP32 DevKit V1
- Parts
- DHT11 or DHT22 sensor
- Level
- Intermediate

Pico W WiFi weather and time on an I2C LCD
MicroPython on a Pico W: join the simulated WiFi, fetch the weather and the time with urequests, and show both on an I2C LCD1602 on GP6 and GP7.
- Board
- Raspberry Pi Pico W
- Parts
- I2C LCD
- Level
- Intermediate

Barometer
A BMP180 read with the Adafruit BMP085 library: temperature to a tenth of a degree, pressure to a pascal, and the altitude that pressure means.
- Board
- Arduino Uno R3
- Parts
- BMP180 pressure sensor
- Level
- Intermediate

Thermometer
A TMP36 on A0 and the temperature on a 16x2 LCD in four-bit mode, with the high and low on the second row.
- Board
- Arduino Uno R3
- Parts
- TMP36 temperature sensor, 16x2 character LCD
- Level
- Intermediate

BME280 on a Pi Zero 2 W with smbus2
A Raspberry Pi Zero 2 W reads a BME280 over I2C with smbus2 and the datasheet formulas: temperature, pressure and humidity every two seconds.
- Board
- Raspberry Pi Zero 2 W
- Parts
- BME280 weather sensor
- Level
- Intermediate

MicroPython thermometer: a thermistor on GPIO 36
MicroPython on an ESP32: a 10k NTC thermistor in a divider on GPIO 36, turned into degrees Celsius with the beta equation every second.
- Board
- ESP32-DevKitC V4
- Parts
- Resistor, 10k NTC thermistor
- Level
- Intermediate

Two barometers
A BME280 and a BMP280 on one I2C bus, told apart by their address straps and their chip ids.
- Board
- ESP32-C3-DevKitM-1
- Parts
- BME280 weather sensor, pressure and temperature
- Level
- Intermediate

Wind and rain station
The SparkFun weather meter kit on an Uno: wind speed from the anemometer, direction from the vane and rain from the bucket, on an I2C LCD.
- Board
- Arduino Uno R3
- Parts
- Weather meter kit, resistor, I2C LCD
- Level
- Intermediate

ESP32 async web server: BME280, slider and relay
ESPAsyncWebServer serves a page with BME280 temperature, humidity and pressure, a slider that dims an LED and a button that switches a relay.
- Board
- ESP32 DevKit V1
- Parts
- BME280 weather sensor, resistor, LED, relay module, DC jack and adapter, +1 more
- Level
- Intermediate

MicroPython WiFi weather on an ESP32
MicroPython on an ESP32 DevKit: network.WLAN joins the simulated access point and urequests fetches the weather from http.
- Board
- ESP32 DevKit V1
- Parts
- Just the board
- Level
- Intermediate

Thermistor thermometer
A 10k thermistor and a 10k resistor make a divider on A0, and the beta equation turns the reading into degrees on a 16x2 LCD.
- Board
- Arduino Uno R3
- Parts
- 10k NTC thermistor, resistor, 16x2 character LCD
- Level
- Intermediate

I2C LCD clock and thermometer
An I2C LCD on A4 and A5 shows the time, kept by a timer interrupt every second, and the temperature from a thermistor on A0.
- Board
- Arduino Uno R3
- Parts
- 10k NTC thermistor, resistor, I2C LCD
- Level
- Intermediate

Falling rain on eight LEDs (74HC595, pins 11, 12 and 13)
Eight LEDs on a 74HC595 (DS 11, ST_CP 12, SH_CP 13) show a drop of light with a fading tail running along them.
- Board
- Arduino Uno R3
- Parts
- 74HC595 shift register, resistor, LED
- Level
- Intermediate

Weather station
A DHT22 on one wire and a 16x2 I2C display on two. Forty bits and a checksum, a first reading that fails, and a sensor that will not be hurried.
- Board
- Arduino Uno R3
- Parts
- DHT11 or DHT22 sensor, I2C LCD
- Level
- Intermediate

LoRa weather station with acknowledgments
A BME280 node sends temperature, humidity and pressure over LoRa with RadioHead, and a gateway acknowledges each reading and shows it on an I2C LCD.
- Board
- Arduino Uno R3
- Parts
- LoRa module, BME280 weather sensor, I2C LCD
- Level
- Advanced
Wiring, libraries and more ideas
Wiring guides
Library pages
More project ideas
- Arduino Uno project ideas
- ESP32 project ideas
- Raspberry Pi Pico project ideas
- Projects with a BME280 sensor
- Projects with an I2C LCD
- Projects with a thermistor
- Projects with a DHT11 or DHT22 sensor
- Projects with a 16x2 LCD
- LED projects for Arduino, ESP32 and Pico
- OLED display projects
- Projects with a 74HC595 shift register