Wiring guide

How to wire a DHT22 to a Raspberry Pi Pico

To wire a DHT22 to a Raspberry Pi Pico, connect VCC to 3V3(OUT), DATA to GP15 (physical pin 20) and GND to GND. The Raspberry Pi Pico is a 3.3 V board, so power the sensor from 3.3 V: the module’s built-in pull-up then keeps DATA at 3.3 V, which the pin can take. The sketch below uses the Adafruit DHT sensor library (DHT.h) library. It prints the temperature and the humidity on the serial monitor every two seconds.

  • 3.3 V logic
  • Library: DHT.h
  • 3 wires
Raspberry Pi Pico · DHT22live0.000 s 0.00x
Click to open it in the editor
The circuit itself, running on the simulator with the sketch below. Press what can be pressed; click anything else to open it in the editor.
Pin to pin

DHT22 to Raspberry Pi Pico wiring table

Every wire in the circuit above, with the part’s pin names and the board’s own labels. The wire colors are the ones the circuit uses; on a real bench any colors work.

DHT22 pinRaspberry Pi Pico pinWire colorWhy
VCC (+)3V3(OUT)redThe sensor runs from 3.3 V, and so does its pull-up, so DATA never rises above what the pin can take.
DATA (out)GP15 (physical pin 20)amberOne wire, both directions: the board pulls it low to ask, the sensor answers with 40 bits.
GND (-)GNDblueA shared ground, or the board cannot read the sensor’s levels.
Voltage

Power and logic levels for DHT22 and Raspberry Pi Pico

Logic level

The Raspberry Pi Pico’s GPIO pins are 3.3 V logic and are not 5 V tolerant. Nothing wired to a pin may go above 3.3 V.

Supply

The DHT22 takes 3.3 V from 3V3(OUT). That pin is the Raspberry Pi Pico’s own regulated 3.3 V output.

This pair

The three-pin module carries a pull-up resistor from DATA to VCC. Powered from VBUS (5 V from USB), that resistor would hold a Raspberry Pi Pico pin at 5 V, which the RP2040 is not rated for. From 3V3 the whole line stays at 3.3 V and the sensor still reads normally.

Pins to leave alone

The numbers in the code are GP numbers, not the physical pin numbers printed beside the header: GP15 is pin 20. GP23 to GP25 are used on the board itself, and GP25 is the LED.

The sketch

The working code for the Raspberry Pi Pico

Library: Adafruit DHT sensor library (DHT.h). This is the sketch the circuit above runs.

DHT22 on Raspberry Pi Pico GP15 (physical pin 20)
#include "DHT.h"

#define DHT_PIN 15     // DATA, GP15 (physical pin 20)
#define DHT_TYPE DHT22

DHT dht(DHT_PIN, DHT_TYPE);

void setup() {
  Serial.begin(115200);
  dht.begin();
  Serial.println("DHT22 on the Raspberry Pi Pico");
}

void loop() {
  delay(2000);                          // the DHT22 measures every 2 s
  float celsius = dht.readTemperature();
  float humidity = dht.readHumidity();
  if (isnan(celsius) || isnan(humidity)) {  // a failed read is NAN
    Serial.println("No reading from the DHT22");
    return;
  }
  Serial.print("Temperature: ");
  Serial.print(celsius, 1);
  Serial.print(" C  Humidity: ");
  Serial.print(humidity, 1);
  Serial.println(" %");
}
Output

What you should see

Open the serial monitor at 115200 baud. The sketch waits two seconds, which is how often a DHT22 can measure, and then prints one line per reading. The sensor starts at 22 degrees C and 50 percent humidity, and the line follows its two sliders when you drag them.

If a read fails the sketch prints No reading from the DHT22 instead of a number. That is what a wrong DATA pin or a missing pull-up looks like.

The serial monitor prints this, recorded from the circuit above left at its defaults:

DHT22 on the Raspberry Pi Pico
Temperature: 22.0 C  Humidity: 50.0 %
Pitfalls

Common mistakes wiring a DHT22 to a Raspberry Pi Pico

Reading faster than every two seconds

A DHT22 needs two seconds between measurements. Ask sooner and it returns the previous reading, or nothing at all, so a fast loop looks like a stuck sensor. Keep the delay(2000), or time the reads with millis().

Powering the module from VBUS (5 V from USB)

It works for a while, which is the trap. The module’s pull-up then holds DATA at 5 V, above the RP2040’s absolute maximum, and the pin can be damaged slowly. Use 3V3, as in the circuit above.

Counting physical pins instead of GP numbers

The sketch says 15, which means GP15, and that is physical pin 20 on the header. Counting 15 pins down the side lands on a different GPIO, and the part never answers.

Build your own DHT22 project

Open this circuit in the editor, change the wiring or the code, and keep your version in a free account.