Projects with an I2C LCD
85 Mokxi projects use an I2C LCD (23 beginner, 44 intermediate and 18 advanced). They run on Arduino Uno, Raspberry Pi Pico and ESP32 boards. Here are 24, from “Water pressure gauge” to “Smart home hub”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.
How to pick your first one
- Start with “Water pressure gauge”, a beginner project that needs a pressure transducer and an I2C LCD.
- Arduino Uno runs 74 of them, Raspberry Pi Pico 5 and ESP32 4. Start on the board you have, or on an Arduino Uno if you are buying one.
- The parts used most here are the push button (28 projects), the buzzer (15) and the piezo speaker (15). With those on hand, most of this list is open to you.
- Before you build one on a real bench, read the I2C LCD wiring guide for your board below. It gives every pin and the voltage notes.
24 projects of 85

Water pressure gauge
A 0.5 to 4.5 V stainless pressure transducer on a water line and a 16x2 I2C LCD: the pressure in psi and bar, with a warning when it drops.
- Board
- Arduino Uno R3
- Parts
- 0.5 to 4.5 V pressure sender, I2C LCD
- Level
- Beginner

Stopwatch with lap times
Stopwatch with lap times on an Arduino Nano and a 16x2 LCD: one button starts, stops and carries on, the other takes laps or resets.
- Board
- Arduino Nano
- Parts
- Arcade button, piezo speaker, I2C LCD
- Level
- Beginner

Electronic voting machine
Electronic voting machine on an Arduino Nano: four buttons to vote, a result button for every count and the winner on an LCD.
- Board
- Arduino Nano
- Parts
- Arcade button, piezo speaker, I2C LCD
- Level
- Beginner

Object counter with an E18-D80NK
An E18-D80NK infrared sensor on pin 2 with the pin’s pull-up: each object that passes adds one to the count on a 16x2 I2C LCD, with a beep.
- Board
- Arduino Uno R3
- Parts
- E18-D80NK IR proximity switch, buzzer, I2C LCD
- Level
- Beginner

Fever thermometer
An MLX90614 reads a forehead without touching it; an I2C LCD shows the temperature, and over 38 C it says FEVER and beeps.
- Board
- Arduino Uno R3
- Parts
- IR thermometer, I2C LCD, piezo speaker
- Level
- Beginner

I2C LCD clock and thermometer
An I2C LCD on A4 and A5 shows the time, kept by a timer interrupt every second, and the temperature from a thermistor on A0.
- Board
- Arduino Uno R3
- Parts
- 10k NTC thermistor, resistor, I2C LCD
- Level
- Intermediate

MicroPython DHT11 and LCD1602 on a Pico
MicroPython on a Raspberry Pi Pico: a DHT11 on GP5 and an I2C LCD1602 on GP14 and GP15 show the temperature and humidity, refreshed every two seconds.
- Board
- Raspberry Pi Pico
- Parts
- DHT11 or DHT22 sensor, resistor, I2C LCD
- Level
- Intermediate

Thermometer on an I2C LCD
A 10 k NTC bead in a divider on A0, the temperature on a 16x2 character LCD over its PCF8574 backpack. Four wires to the display.
- Board
- Arduino Uno R3
- Parts
- 10k NTC thermistor, resistor, I2C LCD
- Level
- Intermediate

Pitot airspeed meter
An MPX5010DP differential pressure sensor on a pitot tube and a 16x2 I2C LCD: the wind’s pressure in pascals and the airspeed it means.
- Board
- Arduino Uno R3
- Parts
- Pressure sensor, I2C LCD
- Level
- Intermediate

Pico W WiFi weather and time on an I2C LCD
MicroPython on a Pico W: join the simulated WiFi, fetch the weather and the time with urequests, and show both on an I2C LCD1602 on GP6 and GP7.
- Board
- Raspberry Pi Pico W
- Parts
- I2C LCD
- Level
- Intermediate

MicroPython DHT readings on an I2C LCD
MicroPython on an ESP32: a DHT22 on GPIO 18 shows temperature and humidity on an I2C LCD1602 (SDA 13, SCL 14), every two seconds.
- Board
- ESP32-DevKitC V4
- Parts
- DHT11 or DHT22 sensor, resistor, I2C LCD
- Level
- Intermediate

Breathalyzer with an MQ-3
An MQ-3 alcohol sensor calibrated in clean air with MQUnifiedsensor.
- Board
- Arduino Uno R3
- Parts
- Traffic light module, alcohol sensor, I2C LCD
- Level
- Intermediate

Guess the number: IR remote and an I2C LCD
The board picks a number from 0 to 99; type guesses on the remote (IR receiver on pin 2), press PLAY/PAUSE to check.
- Board
- Arduino Uno R3
- Parts
- IR receiver and remote, IR remote, I2C LCD
- Level
- Intermediate

RFID reader with an I2C LCD
An RC522 reader on the SPI pins with SS on 10 and RST on 9 reads a card’s UID and shows it on an I2C LCD on A4 and A5.
- Board
- Arduino Uno R3
- Parts
- MFRC522 RFID reader, I2C LCD
- Level
- Intermediate

Touch climate display
An AHT20 and a 16x2 I2C LCD on the same two wires, and a TTP223 touch pad that flips the reading between Celsius and Fahrenheit.
- Board
- Arduino Uno R3
- Parts
- Humidity sensor, I2C LCD, touch sensor
- Level
- Intermediate

MicroPython I2C LCD1602: hello and a counter
MicroPython on an ESP32: an LCD1602 on an I2C backpack, SDA on GPIO 13 and SCL on 14, says hello and counts the seconds.
- Board
- ESP32-DevKitC V4
- Parts
- I2C LCD
- Level
- Intermediate

Pico W room temperature on an I2C LCD
MicroPython on a Pico W: a 10k thermistor divider on GP28 gives the temperature, and an I2C LCD1602 on GP6 and GP7 shows it every second.
- Board
- Raspberry Pi Pico W
- Parts
- I2C LCD, resistor, 10k NTC thermistor
- Level
- Intermediate

Wind and rain station
The SparkFun weather meter kit on an Uno: wind speed from the anemometer, direction from the vane and rain from the bucket, on an I2C LCD.
- Board
- Arduino Uno R3
- Parts
- Weather meter kit, resistor, I2C LCD
- Level
- Intermediate

Pico W guess the number: keypad and LCD
MicroPython on a Pico W: a number game on a 4x4 keypad (rows GP21 to GP18.
- Board
- Raspberry Pi Pico W
- Parts
- I2C LCD, 4x4 keypad
- Level
- Advanced

Access control: RFID card opens a stepper door
An RC522 reader (SS 10, RST 9) checks each card against the one it knows.
- Board
- Arduino Uno R3
- Parts
- MFRC522 RFID reader, 28BYJ-48 stepper and ULN2003, I2C LCD
- Level
- Advanced

Typewriter
A PS/2 keyboard read on an interrupt and printed on a 16x2 LCD: type on it for real and watch the scan codes become letters.
- Board
- ESP32-C3-DevKitM-1
- Parts
- PS/2 keyboard, I2C LCD
- Level
- Advanced

nRF24L01 sensor network with RF24Network
Two nRF24L01 sensor nodes send DS18B20 temperatures to a base node every 2 seconds, and the base shows each one on an LCD.
- Board
- Arduino Uno R3
- Parts
- NRF24L01+ 2.4 GHz radio, I2C LCD, DS18B20 temperature sensor
- Level
- Advanced

LoRa weather station with acknowledgments
A BME280 node sends temperature, humidity and pressure over LoRa with RadioHead, and a gateway acknowledges each reading and shows it on an I2C LCD.
- Board
- Arduino Uno R3
- Parts
- LoRa module, BME280 weather sensor, I2C LCD
- Level
- Advanced

Smart home hub
An ESP32-C3 web dashboard that switches a lamp and a fan through relays, dims a porch light, reads temperature, humidity and motion.
- Board
- ESP32-C3-DevKitM-1
- Parts
- Two-channel relay board, filament lamp, DC motor, LED, resistor, +4 more
- Level
- Advanced