Projects with a TM1637 display
16 Mokxi projects use a TM1637 display (2 beginner, 9 intermediate and 5 advanced). They run on Arduino Uno, Arduino Mega and Pro Micro boards. Here are all of them, from “ESP32 NTP clock on a TM1637 display” to “Elevator controller”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.
How to pick your first one
- Start with “ESP32 NTP clock on a TM1637 display”, a beginner project that needs a TM1637 display.
- Arduino Uno runs 11 of them, Arduino Mega 2 and Pro Micro 2. Start on the board you have, or on an Arduino Uno if you are buying one.
- The parts used most here are the piezo speaker (10 projects), the push button (5) and the arcade button (4). With those on hand, most of this list is open to you.
- Before you build one on a real bench, read the TM1637 four-digit display wiring guide for your board below. It gives every pin and the voltage notes.
16 projects ready to run

ESP32 NTP clock on a TM1637 display
An ESP32 gets the time from an NTP server with NTPClient and shows hours and minutes on a TM1637 four-digit display, the colon blinking every second.
- Board
- ESP32 DevKit V1
- Parts
- TM1637 four-digit display
- Level
- Beginner

Pomodoro timer
Twenty-five minutes of focus and five of rest on a four-digit display, with a red lamp for work, a green one for breaks and a chime at every change.
- Board
- Arduino Uno R3
- Parts
- Resistor, LED, push button, piezo speaker, TM1637 four-digit display
- Level
- Beginner

Desk clock
A DS3231 over I2C and a TM1637 on two wires that are not I2C.
- Board
- Arduino Uno R3
- Parts
- DS3231 real-time clock, TM1637 four-digit display, logic analyzer
- Level
- Intermediate

Piggy bank
A CH-926 coin acceptor counts each coin’s pulses on an interrupt, and a TM1637 display adds up the savings in dollars and cents.
- Board
- Arduino Uno R3
- Parts
- Coin acceptor, TM1637 four-digit display
- Level
- Intermediate

Whack-a-mole
Four lamps, four buttons, a piezo and a score display on an Uno: hit each mole before it ducks in a thirty-second round that speeds up as you score.
- Board
- Arduino Uno R3
- Parts
- Resistor, LED, push button, piezo speaker, TM1637 four-digit display
- Level
- Intermediate

New Year's countdown
A DS3231 and a four-digit display count down to midnight on New Year’s Eve.
- Board
- Arduino Uno R3
- Parts
- DS3231 real-time clock, TM1637 four-digit display, resistor, WS2812 NeoPixel LEDs
- Level
- Intermediate

Alarm clock
A DS1302 keeps the time and a TM1637 shows it; at 7:00 a piezo beeps until the button stops it. It starts at 6:59:50, so wait ten seconds.
- Board
- Arduino Uno R3
- Parts
- Real-time clock, TM1637 four-digit display, push button, piezo speaker
- Level
- Intermediate

Coin pusher
Drop coins in front of a sweeping servo pusher, count the ones that fall off the front, win a jackpot light show, and watch it back out of a jam.
- Board
- Arduino Uno R3
- Parts
- Arcade button, piezo speaker, FC-51 IR obstacle sensor, TM1637 four-digit display, WS2812 NeoPixel LEDs, +2 more
- Level
- Intermediate

Zombie tripwire
An ultrasonic tripwire across a corridor: every walker is counted on a display, a traffic light rises from green to red.
- Board
- Arduino Uno R3
- Parts
- HC-SR04 ultrasonic sensor, piezo speaker, traffic light module, TM1637 four-digit display
- Level
- Intermediate

Find the emergency broadcast
Turn a knob across the FM band to find a hidden station: the static fades and a traffic light warms from red to green as you close in.
- Board
- Arduino Uno R3
- Parts
- Traffic light module, TM1637 four-digit display, piezo speaker, potentiometer
- Level
- Intermediate

Defuse the doomsday device
A TM1637 counts down a minute, a clue lamp blinks a number, and three buttons are the wires: cut the right one before time runs out.
- Board
- Arduino Uno R3
- Parts
- Resistor, LED, push button, piezo speaker, TM1637 four-digit display
- Level
- Intermediate

Autopilot and landing gear panel
An autopilot knob for heading, altitude and vertical speed on a four-digit display, an AP button.
- Board
- SparkFun Pro Micro
- Parts
- TM1637 four-digit display, KY-040 rotary encoder, slide switch, arcade button, LED, +1 more
- Level
- Advanced

Spaceship control panel
Arm three systems, pass the go/no-go poll, lift the safety and launch.
- Board
- Arduino Mega 2560 R3
- Parts
- Slide switch, LED arcade button, TM1637 four-digit display, piezo speaker, WS2812 NeoPixel LEDs, +7 more
- Level
- Advanced

Pinball table
A table you can play on a Mega: flippers, pop bumpers on a kicker solenoid, targets, a drain beam and a plunger, with a four-digit score.
- Board
- Arduino Mega 2560 R3
- Parts
- TM1637 four-digit display, WS2812 NeoPixel LEDs, pinball table, MOSFET, diode, +3 more
- Level
- Advanced

H-pattern shifter and handbrake
Two pots read an H-pattern gate with hysteresis and push-down reverse, two microswitches make sequential paddles and a hall sensor is the handbrake.
- Board
- SparkFun Pro Micro
- Parts
- TM1637 four-digit display, limit switch, slide potentiometer, arcade button, 49E linear hall sensor
- Level
- Advanced

Elevator controller
A three-floor elevator with call buttons, a servo cab, a door that will not close on you, and a display that shows the floor.
- Board
- Arduino Uno R3
- Parts
- FC-51 IR obstacle sensor, servo motor, push button, piezo speaker, TM1637 four-digit display
- Level
- Advanced
Wiring, libraries and more ideas
Wiring guides
Library pages
More project ideas
- Arduino Uno project ideas
- Arduino Mega project ideas
- Pro Micro and Leonardo project ideas
- ESP32 project ideas
- Projects with a piezo speaker
- Projects with a push button
- Projects with an arcade button
- LED projects for Arduino, ESP32 and Pico
- NeoPixel projects
- Servo motor projects
- Projects with a DS3231 real-time clock