Project ideas by board

Arduino Nano project ideas

10 Mokxi projects run on an Arduino Nano (5 beginner, 3 intermediate and 2 advanced). Here are all of them, from “Ultrasonic theremin” to “Camera slider with eased moves”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

How to pick your first one

  • Start with “Electronic voting machine”, a beginner project that needs an arcade button, a piezo speaker and an I2C LCD.
  • Most of them are beginner projects. Pick one a level below what you think you can do, finish it, then move up.
  • The parts used most here are the piezo speaker (5 projects), the arcade button (4) and the LED (4). With those on hand, most of this list is open to you.
  • The Nano is an Uno on a breadboard-friendly stick. Same chip, same pins by number, so any Uno sketch runs on it.
Projects

10 projects ready to run

  • Ultrasonic theremin, drawn in the Mokxi editor

    Ultrasonic theremin

    Ultrasonic theremin on an Arduino Nano: wave a hand over an HC-SR04 to play notes of a pentatonic scale, or glide the pitch like a real theremin.

    Board
    Arduino Nano
    Parts
    HC-SR04 ultrasonic sensor, arcade button, piezo speaker
    Level
    Beginner
    Open in the simulator
  • Stopwatch with lap times, drawn in the Mokxi editor

    Stopwatch with lap times

    Stopwatch with lap times on an Arduino Nano and a 16x2 LCD: one button starts, stops and carries on, the other takes laps or resets.

    Board
    Arduino Nano
    Parts
    Arcade button, piezo speaker, I2C LCD
    Level
    Beginner
    Open in the simulator
  • Nano dial, drawn in the Mokxi editor

    Nano dial

    A potentiometer on the Nano's A7, the analog-only pin an Uno does not have, fades an LED on pin 9.

    Board
    Arduino Nano
    Parts
    Potentiometer, resistor, LED
    Level
    Beginner
    Open in the simulator
  • Electronic voting machine, drawn in the Mokxi editor

    Electronic voting machine

    Electronic voting machine on an Arduino Nano: four buttons to vote, a result button for every count and the winner on an LCD.

    Board
    Arduino Nano
    Parts
    Arcade button, piezo speaker, I2C LCD
    Level
    Beginner
    Open in the simulator
  • Tug of war game, drawn in the Mokxi editor

    Tug of war game

    Tug of war game for two players on a 15-LED NeoPixel strip: every button press pulls the light one LED your way, and the first to pull it off wins.

    Board
    Arduino Nano
    Parts
    Arcade button, WS2812 NeoPixel LEDs, piezo speaker
    Level
    Beginner
    Open in the simulator
  • Animated diorama: DFPlayer sound + stepper, drawn in the Mokxi editor

    Animated diorama: DFPlayer sound + stepper

    A button plays a C-3PO line on a DFPlayer Mini while a 28BYJ-48 turns R2-D2’s dome.

    Board
    Arduino Nano
    Parts
    DFPlayer Mini MP3 module, resistor, push button, 8 ohm speaker, 28BYJ-48 stepper and ULN2003
    Level
    Intermediate
    Open in the simulator
  • Laser tag: two Nanos, drawn in the Mokxi editor

    Laser tag: two Nanos

    Infrared laser tag for two Arduino Nanos: each button fires an NEC code through an IR LED, and the other player’s VS1838B counts the hit.

    Board
    Arduino Nano
    Parts
    Infrared LED, IR receiver and remote, resistor, push button, LED, +1 more
    Level
    Intermediate
    Open in the simulator
  • Drum pads, drawn in the Mokxi editor

    Drum pads

    Arduino drum pads: three force-sensing resistors play a kick, a snare and a hi-hat on a piezo, harder hits longer.

    Board
    Arduino Nano
    Parts
    Force-sensing resistor, piezo speaker
    Level
    Intermediate
    Open in the simulator
  • Eurorack CV quantizer, drawn in the Mokxi editor

    Eurorack CV quantizer

    A control voltage snapped to the nearest note of a scale and sent out at one volt per octave through a filtered PWM DAC.

    Board
    Arduino Nano
    Parts
    Potentiometer, resistor, capacitor, LED, slide switch, +2 more
    Level
    Advanced
    Open in the simulator
  • Camera slider with eased moves, drawn in the Mokxi editor

    Camera slider with eased moves

    A NEMA 17 on an A4988 homes to an end switch, then makes a video move that speeds up and slows down evenly, or a timelapse that moves.

    Board
    Arduino Nano
    Parts
    LED, resistor, potentiometer, push button, slide switch, +3 more
    Level
    Advanced
    Open in the simulator