Project ideas by part

Projects with a water pump

12 Mokxi projects use a mini water pump (3 beginner, 7 intermediate and 2 advanced). They run on Arduino Uno and Raspberry Pi Pico boards. Here are all of them, from “Aquarium air pump and doser” to “Fire fighting robot”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

How to pick your first one

  • Start with “Pico W water pump on a motor driver”, a beginner project that needs an L9110S motor driver and a water pump.
  • Arduino Uno runs 11 of them and Raspberry Pi Pico 1. Start on the board you have, or on an Arduino Uno if you are buying one.
  • The parts used most here are the I2C LCD (5 projects), the push button (5) and the relay module (5). With those on hand, most of this list is open to you.
  • Before you build one on a real bench, open the mini water pump part page for its pins and what each one does.
Projects

12 projects ready to run

  • Aquarium air pump and doser, drawn in the Mokxi editor

    Aquarium air pump and doser

    Two D4184 modules on pins 9 and 10 run a 12 V air pump all the time and a peristaltic pump for 3 s, 5 ml, every 20 s.

    Board
    Arduino Uno R3
    Parts
    DC jack and adapter, D4184 MOSFET module, mini water pump
    Level
    Beginner
    Open in the simulator
  • Pico W water pump on a motor driver, drawn in the Mokxi editor

    Pico W water pump on a motor driver

    MicroPython on a Pico W: GP14 high and GP15 low keep a small DC water pump running through a two-input motor driver.

    Board
    Raspberry Pi Pico W
    Parts
    L9110S motor driver, mini water pump
    Level
    Beginner
    Open in the simulator
  • Mini pump plant waterer, drawn in the Mokxi editor

    Mini pump plant waterer

    A capacitive soil probe watches the pot; when it reads dry, a relay runs the mini pump for three seconds, then waits for the water to soak in.

    Board
    Arduino Uno R3
    Parts
    Capacitive soil moisture sensor, relay module, mini water pump
    Level
    Beginner
    Open in the simulator
  • Automatic soap dispenser: ultrasonic on 8 and 7, pump on 2, drawn in the Mokxi editor

    Automatic soap dispenser: ultrasonic on 8 and 7, pump on 2

    An HC-SR04 (TRIG 8, ECHO 7) sees a hand under the spout and runs a mini water pump for a moment through an L293D whose 1A input is on pin 2.

    Board
    Arduino Uno R3
    Parts
    L293D motor driver, mini water pump, HC-SR04 ultrasonic sensor
    Level
    Intermediate
    Open in the simulator
  • Ultrasonic water tank level monitor, drawn in the Mokxi editor

    Ultrasonic water tank level monitor

    An HC-SR04 in the lid reads the water level onto an I2C LCD, a relay pump refills from 20 to 90 percent, and a buzzer warns of an overflow.

    Board
    Arduino Uno R3
    Parts
    HC-SR04 ultrasonic sensor, relay module, mini water pump, buzzer, I2C LCD
    Level
    Intermediate
    Open in the simulator
  • Water level controller with float switches, drawn in the Mokxi editor

    Water level controller with float switches

    Two float switches keep a tank between its low and high marks with a pump on a relay; a stuck float or a pump running dry stops it and blinks red.

    Board
    Arduino Uno R3
    Parts
    Float switch, push button, resistor, LED, relay module, +2 more
    Level
    Intermediate
    Open in the simulator
  • Washing machine, drawn in the Mokxi editor

    Washing machine

    Pick a cycle on the knob and press START: it fills, washes with a reversing drum, drains and spins, and it only spins with the lid shut and locked.

    Board
    Arduino Uno R3
    Parts
    Servo motor, two-channel relay board, solenoid, mini water pump, L9110S motor driver, +6 more
    Level
    Intermediate
    Open in the simulator
  • Bottling line, drawn in the Mokxi editor

    Bottling line

    A belt brings each bottle to the filler, a pump fills it until the float switch trips, and the LCD counts them.

    Board
    Arduino Uno R3
    Parts
    Two-channel relay board, DC motor, mini water pump, FC-51 IR obstacle sensor, float switch, +4 more
    Level
    Intermediate
    Open in the simulator
  • Car wash, drawn in the Mokxi editor

    Car wash

    Drive a car up to the sensor and press START: it rinses, soaps, brushes, rinses and dries on a timeline.

    Board
    Arduino Uno R3
    Parts
    Traffic light module, two-channel relay board, solenoid, mini water pump, MX1508 dual motor driver, +7 more
    Level
    Intermediate
    Open in the simulator
  • Sump pump controller, drawn in the Mokxi editor

    Sump pump controller

    A teaching model of a sump controller: two floats run a relay pump, an ACS712 checks that current really flows, and alarms catch a dead pump.

    Board
    Arduino Uno R3
    Parts
    Float switch, ACS712 current sensor, relay module, mini water pump, slide switch, +4 more
    Level
    Intermediate
    Open in the simulator
  • Plant monitor: light, soil, temperature and a pump, drawn in the Mokxi editor

    Plant monitor: light, soil, temperature and a pump

    A photoresistor on A0, a soil moisture sensor on A1 and a thermistor on A2 report to an I2C LCD; when the soil dries out.

    Board
    Arduino Uno R3
    Parts
    Photoresistor, resistor, 10k NTC thermistor, L293D motor driver, capacitive soil moisture sensor, +2 more
    Level
    Advanced
    Open in the simulator
  • Fire fighting robot, drawn in the Mokxi editor

    Fire fighting robot

    Three flame sensors steer a 2WD car on an L298N to the fire, then a relay runs a water pump while a servo sweeps the nozzle until the flame is out.

    Board
    Arduino Uno R3
    Parts
    L298N motor driver, 2WD robot car chassis, flame sensor, servo motor, relay module, +1 more
    Level
    Advanced
    Open in the simulator