Projects with a two-channel relay board
9 Mokxi projects use a two-channel relay board (7 intermediate and 2 advanced). They run on Arduino Uno and ESP32 boards. Here are all of them, from “Relays reverse a motor” to “Merge jam”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.
How to pick your first one
- Start with “Relays reverse a motor”, an intermediate project that needs a resistor, a transistor, a diode and 3 more parts.
- Arduino Uno runs 8 of them and ESP32 1. Start on the board you have, or on an Arduino Uno if you are buying one.
- The parts used most here are the DC motor (8 projects), the I2C LCD (7) and the push button (6). With those on hand, most of this list is open to you.
- Before you build one on a real bench, open the two-channel relay board part page for its pins and what each one does.
9 projects ready to run

Relays reverse a motor
Two motors turned both ways by relays: one on a two-channel board wired as an H bridge, one on a bare DPDT relay switched by a transistor.
- Board
- Arduino Uno R3
- Parts
- Resistor, transistor, diode, DPDT relay, DC motor, +1 more
- Level
- Intermediate

Bottling line
A belt brings each bottle to the filler, a pump fills it until the float switch trips, and the LCD counts them.
- Board
- Arduino Uno R3
- Parts
- Two-channel relay board, DC motor, mini water pump, FC-51 IR obstacle sensor, float switch, +4 more
- Level
- Intermediate

Reject station
A quality check that tracks each part: an HC-SR04 measures the part's height at the gate.
- Board
- Arduino Uno R3
- Parts
- Servo motor, traffic light module, two-channel relay board, DC motor, alarm siren, +3 more
- Level
- Intermediate

Car wash
Drive a car up to the sensor and press START: it rinses, soaps, brushes, rinses and dries on a timeline.
- Board
- Arduino Uno R3
- Parts
- Traffic light module, two-channel relay board, solenoid, mini water pump, MX1508 dual motor driver, +7 more
- Level
- Intermediate

Turn signals and hazard flasher
Left, right and hazard buttons flash two 12 V bulbs a side through a relay board at 90 a minute.
- Board
- Arduino Uno R3
- Parts
- Push button, resistor, LED, two-channel relay board, INA219 current monitor, +3 more
- Level
- Intermediate

Packaging line
An E18-D80NK counts items into a box; when the count reaches the box size set with a button, the feed relay stops.
- Board
- Arduino Uno R3
- Parts
- Servo motor, buzzer, push button, two-channel relay board, DC motor, +3 more
- Level
- Intermediate

Washing machine
Pick a cycle on the knob and press START: it fills, washes with a reversing drum, drains and spins, and it only spins with the lid shut and locked.
- Board
- Arduino Uno R3
- Parts
- Servo motor, two-channel relay board, solenoid, mini water pump, L9110S motor driver, +6 more
- Level
- Intermediate

Smart home hub
An ESP32-C3 web dashboard that switches a lamp and a fan through relays, dims a porch light, reads temperature, humidity and motion.
- Board
- ESP32-C3-DevKitM-1
- Parts
- Two-channel relay board, filament lamp, DC motor, LED, resistor, +4 more
- Level
- Advanced

Merge jam
Two feeder conveyors take turns putting items onto one shared belt, counted by three E18-D80NK sensors.
- Board
- Arduino Uno R3
- Parts
- Traffic light module, E18-D80NK IR proximity switch, two-channel relay board, DC motor, push button, +1 more
- Level
- Advanced