Project ideas by part

Projects with a capacitor

29 Mokxi projects use a capacitor (13 beginner, 13 intermediate and 3 advanced). They run on Arduino Uno and Raspberry Pi Pico boards, and 20 need no board at all. Here are 24, from “Pico W micro switch on GP14” to “Op-amp low pass on the bench”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

How to pick your first one

  • Start with “Operating point and sweep”, a beginner project that needs a resistor and a capacitor.
  • Arduino Uno runs 4 of them, Raspberry Pi Pico 3 and 20 need no board at all. Start on the board you have, or on an Arduino Uno if you are buying one.
  • The parts used most here are the LED (11 projects), the NE555 timer (7) and the slide switch (5). With those on hand, most of this list is open to you.
  • Before you build one on a real bench, open the capacitor part page for its pins and what each one does.
Projects

24 projects of 29

  • Pico W micro switch on GP14, drawn in the Mokxi editor

    Pico W micro switch on GP14

    MicroPython on a Pico W: a lever micro switch with its common on GP14 reads 1 while pressed and 0 at rest, and prints each change.

    Board
    Raspberry Pi Pico W
    Parts
    Limit switch, resistor, capacitor
    Level
    Beginner
    Open in the simulator
  • Operating point and sweep, drawn in the Mokxi editor

    Operating point and sweep

    A 10 k divider and a 10 k / 10 uF RC on one board, for reading every node at once and sweeping the supply or a resistor.

    Board
    No board
    Parts
    Resistor, capacitor
    Level
    Beginner
    Open in the simulator
  • Pico W slide switch on GP14, drawn in the Mokxi editor

    Pico W slide switch on GP14

    MicroPython on a Pico W: a slide switch puts GP14 on 3.3 V or on ground, with a 10k and a 100 nF to steady it, and the program prints each side.

    Board
    Raspberry Pi Pico W
    Parts
    Slide switch, resistor, capacitor
    Level
    Beginner
    Open in the simulator
  • RC filter on the bench, drawn in the Mokxi editor

    RC filter on the bench

    A function generator into an RC low pass, with a two-channel scope on both ends and a multimeter reading the output.

    Board
    No board
    Parts
    Function generator, resistor, capacitor, oscilloscope, multimeter
    Level
    Beginner
    Open in the simulator
  • NE556 two blinkers, drawn in the Mokxi editor

    NE556 two blinkers

    The two 555 timers in one NE556, each an astable with its own LED: 1.5 Hz and 3.2 Hz from one chip on one 5 V supply.

    Board
    No board
    Parts
    NE556 dual timer, resistor, capacitor, LED
    Level
    Beginner
    Open in the simulator
  • The rest of the dial, drawn in the Mokxi editor

    The rest of the dial

    A board with no power on it and one meter: diode, ohms, capacitance and continuity, the four positions that only mean anything with the supply off.

    Board
    No board
    Parts
    LED, capacitor, resistor, multimeter
    Level
    Beginner
    Open in the simulator
  • A logic probe, drawn in the Mokxi editor

    A logic probe

    A 555 clock with a logic probe on its output and another on a column nothing is driving: pulsing, and the floating input a voltmeter cannot find.

    Board
    No board
    Parts
    Resistor, NE555 timer, capacitor, logic probe
    Level
    Beginner
    Open in the simulator
  • TLC555 blinker on 3.3 V, drawn in the Mokxi editor

    TLC555 blinker on 3.3 V

    The 555 blinker, wire for wire, on a 3.3 V supply with a TLC555: the CMOS 555 runs from 2 V where an NE555 will not start, at the same 1.4 or 7.4 Hz.

    Board
    No board
    Parts
    Resistor, TLC555 CMOS timer, slide switch, capacitor, LED
    Level
    Beginner
    Open in the simulator
  • 7805 voltage regulator circuit, drawn in the Mokxi editor

    7805 voltage regulator circuit

    A 9 V battery into a 7805 with its 0.33 uF and 0.1 uF capacitors: 5 V out to an LED, until the battery sags below about 6.7 V.

    Board
    No board
    Parts
    Battery: AA, voltage regulator, capacitor, resistor, LED
    Level
    Beginner
    Open in the simulator
  • Doorbell, drawn in the Mokxi editor

    Doorbell

    A pushbutton lifts the 555 out of reset and a 4 Hz astable beeps the buzzer.

    Board
    No board
    Parts
    Resistor, NE555 timer, capacitor, push button, buzzer
    Level
    Beginner
    Open in the simulator
  • Breathing LED, drawn in the Mokxi editor

    Breathing LED

    One PWM pin, two LEDs: one sees the raw 1 kHz chopping, the other an RC filter smoothing it.

    Board
    ESP32-C3-DevKitM-1
    Parts
    Resistor, LED, capacitor
    Level
    Intermediate
    Open in the simulator
  • RS-232 loopback, drawn in the Mokxi editor

    RS-232 loopback

    The Uno’s TX goes out through a MAX232 at RS-232 levels, round a loopback jumper and back in on pin 8, the way a COM port is tested.

    Board
    Arduino Uno R3
    Parts
    RS-232 transceiver, capacitor
    Level
    Intermediate
    Open in the simulator
  • 555 on the bench, drawn in the Mokxi editor

    555 on the bench

    A 555 astable with a scope on its output and its timing capacitor and a multimeter reading the average: the frequency.

    Board
    No board
    Parts
    Resistor, NE555 timer, capacitor, oscilloscope, multimeter
    Level
    Intermediate
    Open in the simulator
  • Decade chaser, drawn in the Mokxi editor

    Decade chaser

    A 555 astable clocks a CD4017 decade counter and ten LEDs take turns to light, with no microcontroller.

    Board
    No board
    Parts
    NE555 timer, resistor, capacitor, CD4017 decade counter, LED
    Level
    Intermediate
    Open in the simulator
  • Automatic curtain opener with a stepper motor, drawn in the Mokxi editor

    Automatic curtain opener with a stepper motor

    A NEMA 17 on an A4988 homes to an end switch, opens the curtain at dawn and closes it at dusk, with a button to open, close or stop and a speed knob.

    Board
    Arduino Uno R3
    Parts
    A4988 stepper driver, NEMA 17 stepper motor, DC jack and adapter, capacitor, limit switch, +4 more
    Level
    Intermediate
    Open in the simulator
  • LM386 speaker amp, drawn in the Mokxi editor

    LM386 speaker amp

    An Uno plays a tune with tone() on pin 8, and an LM386 with a gain of 20 drives an 8 ohm speaker from a 9 V battery.

    Board
    Arduino Uno R3
    Parts
    Battery: AA, LM386 audio amplifier, resistor, capacitor, 8 ohm speaker
    Level
    Intermediate
    Open in the simulator
  • Mains to 17 V DC, drawn in the Mokxi editor

    Mains to 17 V DC

    A 230 V to 12-0-12 V mains transformer, two 1N4007s as a full-wave rectifier and 1000 uF of smoothing.

    Board
    No board
    Parts
    Signal generator, mains transformer, diode, capacitor, resistor, +2 more
    Level
    Intermediate
    Open in the simulator
  • Waveform lab, drawn in the Mokxi editor

    Waveform lab

    PWM audio on an Uno: Timer 1 and an RC filter turn pulse widths into a sine, triangle, sawtooth or square wave on a scope.

    Board
    Arduino Uno R3
    Parts
    Resistor, capacitor, push button, potentiometer, piezo speaker, +1 more
    Level
    Intermediate
    Open in the simulator
  • CD4060 timer, drawn in the Mokxi editor

    CD4060 timer

    A CD4060 oscillates on two resistors and a capacitor and divides it down to blink four LEDs, each at half the rate of the one before.

    Board
    No board
    Parts
    CD4060 counter with oscillator, resistor, capacitor, LED
    Level
    Intermediate
    Open in the simulator
  • Pico W alarm siren and lamp on a slide switch, drawn in the Mokxi editor

    Pico W alarm siren and lamp on a slide switch

    MicroPython on a Pico W: a slide switch on GP17 turns on a siren, a passive buzzer on GP15 sweeping 130 to 800 Hz with an LED on GP16 pulsing in step.

    Board
    Raspberry Pi Pico W
    Parts
    Piezo speaker, transistor, resistor, slide switch, capacitor, +1 more
    Level
    Intermediate
    Open in the simulator
  • Counting a 555, drawn in the Mokxi editor

    Counting a 555

    A 555 astable with a frequency counter and a multimeter on its Hz range: frequency, period, duty and a running pulse total, against the arithmetic.

    Board
    No board
    Parts
    Resistor, NE555 timer, capacitor, frequency counter, multimeter
    Level
    Intermediate
    Open in the simulator
  • Eurorack CV quantizer, drawn in the Mokxi editor

    Eurorack CV quantizer

    A control voltage snapped to the nearest note of a scale and sent out at one volt per octave through a filtered PWM DAC.

    Board
    Arduino Nano
    Parts
    Potentiometer, resistor, capacitor, LED, slide switch, +2 more
    Level
    Advanced
    Open in the simulator
  • Decoder chaser, drawn in the Mokxi editor

    Decoder chaser

    A 74HC14 oscillator clocks a 74HC161 counter and a 74HC138 decoder lights one LED of eight at a time.

    Board
    No board
    Parts
    74HC14 Schmitt inverter, resistor, capacitor, 74HC161 4-bit counter, 74HC138 3-to-8 decoder, +1 more
    Level
    Advanced
    Open in the simulator
  • Op-amp low pass on the bench, drawn in the Mokxi editor

    Op-amp low pass on the bench

    A signal generator into an inverting op-amp low pass biased off a single 5 V rail, with a scope on the output: a real gain in the pass band.

    Board
    No board
    Parts
    Function generator, resistor, capacitor, op-amp, oscilloscope
    Level
    Advanced
    Open in the simulator