Project ideas by board

Electronics projects with no code

82 Mokxi projects have no microcontroller in them (49 beginner, 26 intermediate and 7 advanced). Here are 24 to start with, from “Operating point and sweep” to “Up/down counter”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

How to pick your first one

  • Start with “A divider, measured”, a beginner project that needs a resistor and a multimeter.
  • Most of them are beginner projects. Pick one a level below what you think you can do, finish it, then move up.
  • The parts used most here are the LED (32 projects), the capacitor (20) and the slide switch (15). With those on hand, most of this list is open to you.
  • With no microcontroller, the simulator solves the circuit itself, so a changed resistor or capacitor shows its effect the moment you press Run.
Projects

24 projects of 82

  • Operating point and sweep, drawn in the Mokxi editor

    Operating point and sweep

    A 10 k divider and a 10 k / 10 uF RC on one board, for reading every node at once and sweeping the supply or a resistor.

    Board
    No board
    Parts
    Resistor, capacitor
    Level
    Beginner
    Open in the simulator
  • ULN2803A switching four 12 V lamps, drawn in the Mokxi editor

    ULN2803A switching four 12 V lamps

    Four slide switches on a ULN2803A's inputs, four 12 V lamps on its outputs: each channel sinks its lamp to about 0.87 V.

    Board
    No board
    Parts
    ULN2803A Darlington array, slide switch, filament lamp
    Level
    Beginner
    Open in the simulator
  • Plus and minus 5 V, drawn in the Mokxi editor

    Plus and minus 5 V

    Two 12 V sources make a split supply, and a 7805 and a 7905 turn it into +5 V and -5 V, each with a load on it.

    Board
    No board
    Parts
    DC voltage source, voltage regulator, resistor
    Level
    Beginner
    Open in the simulator
  • USB to 3.3 V, drawn in the Mokxi editor

    USB to 3.3 V

    A USB-C breakout on a computer port feeds an AP2112K-3.3 low dropout regulator, which lights an LED at 3.3 V.

    Board
    No board
    Parts
    USB power, voltage regulator, resistor, LED
    Level
    Beginner
    Open in the simulator
  • A divider, measured, drawn in the Mokxi editor

    A divider, measured

    Three resistors from 5 V to ground with a multimeter on the taps: volts, amps, ohms and continuity on the simplest circuit there is.

    Board
    No board
    Parts
    Resistor, multimeter
    Level
    Beginner
    Open in the simulator
  • BCD display, drawn in the Mokxi editor

    BCD display

    Four DIP switches set a number in binary and a CD4511 shows it as a digit on a seven-segment display.

    Board
    No board
    Parts
    4-way DIP switch, 4-resistor network, CD4511 7-segment driver, seven-segment display, resistor
    Level
    Beginner
    Open in the simulator
  • NE556 two blinkers, drawn in the Mokxi editor

    NE556 two blinkers

    The two 555 timers in one NE556, each an astable with its own LED: 1.5 Hz and 3.2 Hz from one chip on one 5 V supply.

    Board
    No board
    Parts
    NE556 dual timer, resistor, capacitor, LED
    Level
    Beginner
    Open in the simulator
  • LM317 adjustable supply, drawn in the Mokxi editor

    LM317 adjustable supply

    An LM317 on a 12 V adapter with 240 ohms and a 2 k pot: Vout = 1.25 V x (1 + R2/R1), from 1.25 V up to the dropout, with an LED on the output.

    Board
    No board
    Parts
    DC jack and adapter, LM317 regulator, resistor, potentiometer, LED
    Level
    Beginner
    Open in the simulator
  • 74HC decoder, mux and adder drawer, drawn in the Mokxi editor

    74HC decoder, mux and adder drawer

    12 chips on breadboards, powered, every input tied low and ready to rewire.

    Board
    No board
    Parts
    74HC147 priority encoder, 74HC148 priority encoder, 74HC151 8-input multiplexer, 74HC153 dual 4-input multiplexer, 74HC157 quad 2-input multiplexer, +7 more
    Level
    Beginner
    Open in the simulator
  • NPN transistor switch, drawn in the Mokxi editor

    NPN transistor switch

    A 2N2222 switching an LED from a slide switch through a 1 k base resistor, with real Gummel-Poon currents in the base and collector.

    Board
    No board
    Parts
    Resistor, LED, transistor, slide switch
    Level
    Beginner
    Open in the simulator
  • What is this part?, drawn in the Mokxi editor

    What is this part?

    Two component testers with unknown parts in the sockets: one names a transistor and finds its base, collector and emitter.

    Board
    No board
    Parts
    Transistor, LED, component tester
    Level
    Beginner
    Open in the simulator
  • Doorbell, drawn in the Mokxi editor

    Doorbell

    A pushbutton lifts the 555 out of reset and a 4 Hz astable beeps the buzzer.

    Board
    No board
    Parts
    Resistor, NE555 timer, capacitor, push button, buzzer
    Level
    Beginner
    Open in the simulator
  • TL072 amplifier on +-12 V, drawn in the Mokxi editor

    TL072 amplifier on +-12 V

    A TL072 inverting amplifier with a gain of -4.7 on a +12 V and -12 V supply: a 1 V sine in, a 4.7 V sine out, upside down and both sides of ground.

    Board
    No board
    Parts
    Function generator, TL072 dual JFET op-amp, resistor, oscilloscope
    Level
    Intermediate
    Open in the simulator
  • Dark detector, drawn in the Mokxi editor

    Dark detector

    An op-amp comparator, an LDR and a pot light an LED when the room goes dark, no board, on a half-size breadboard.

    Board
    No board
    Parts
    Photoresistor, resistor, potentiometer, op-amp, LED
    Level
    Intermediate
    Open in the simulator
  • JK flip-flop counter, drawn in the Mokxi editor

    JK flip-flop counter

    Two JK flip-flops in a 74HC112 toggle on each falling clock edge and count 0 to 3 in binary on two LEDs.

    Board
    No board
    Parts
    Clock, 74HC112 dual JK flip-flop, resistor, LED
    Level
    Intermediate
    Open in the simulator
  • Counting clock, drawn in the Mokxi editor

    Counting clock

    A program counter built from NAND gates, counting one step clock tick at a time, with its LOAD tied to 0 by a constant bit.

    Board
    No board
    Parts
    Number switch, constant bit, bit switch, step clock, logic gate, +1 more
    Level
    Intermediate
    Open in the simulator
  • Switch shifter, drawn in the Mokxi editor

    Switch shifter

    A 74HC165 loads an 8-way DIP switch at the press of a button and clocks the byte out one bit a second onto an LED.

    Board
    No board
    Parts
    Clock, push button, resistor, 8-way DIP switch, 8-resistor network, +2 more
    Level
    Intermediate
    Open in the simulator
  • BSS138 level shifter, drawn in the Mokxi editor

    BSS138 level shifter

    One channel of the bi-directional 3.3 V to 5 V level shifter: a BSS138 and two 10k pull-ups. Pull either side low and the other follows.

    Board
    No board
    Parts
    MOSFET, resistor, slide switch, multimeter
    Level
    Intermediate
    Open in the simulator
  • LM339 window comparator, drawn in the Mokxi editor

    LM339 window comparator

    Two LM339 comparators with their open-collector outputs wired together light one LED whenever a knob leaves the window from 1.67 V to 3.33 V.

    Board
    No board
    Parts
    Potentiometer, LM339 quad comparator, resistor, LED
    Level
    Intermediate
    Open in the simulator
  • Op-amp amplifier, gain of 10, drawn in the Mokxi editor

    Op-amp amplifier, gain of 10

    An inverting op-amp amplifier on a single 5 V supply: a 0.2 V sine in, a 2 V sine out, upside down, with clipping and a frequency response to explore.

    Board
    No board
    Parts
    Function generator, resistor, op-amp, oscilloscope
    Level
    Intermediate
    Open in the simulator
  • NAND latch, drawn in the Mokxi editor

    NAND latch

    Two cross-coupled 74HC00 gates hold one bit, and a slide switch sets and resets it.

    Board
    No board
    Parts
    Slide switch, 74HC00 quad NAND, resistor, LED
    Level
    Intermediate
    Open in the simulator
  • Five StepStick drivers left alone, drawn in the Mokxi editor

    Five StepStick drivers left alone

    TMC2208, TMC2209, TMC2100, DRV8834 and DRV8880 on one 200 Hz clock each: left alone, each steps at its own default resolution.

    Board
    No board
    Parts
    TMC2208 stepper driver, NEMA 17 stepper motor, clock, TMC2209 stepper driver, TMC2100 stepper driver, +2 more
    Level
    Intermediate
    Open in the simulator
  • Full adder, drawn in the Mokxi editor

    Full adder

    Three 74HC chips add two bits and a carry, with the sum and carry on LEDs.

    Board
    No board
    Parts
    Slide switch, 74HC86 quad XOR, 74HC08 quad AND, 74HC32 quad OR, resistor, +1 more
    Level
    Advanced
    Open in the simulator
  • Up/down counter, drawn in the Mokxi editor

    Up/down counter

    A slide switch and a 74HC02 steer a clock into a 74HC193, which counts up or down in binary on four LEDs.

    Board
    No board
    Parts
    Clock, slide switch, resistor, 74HC02 quad NOR, 74HC193 up/down counter, +1 more
    Level
    Advanced
    Open in the simulator

See all 82 Electronics projects with no code projects on the templates page