Project ideas by part

Projects with a 28BYJ-48 stepper motor

13 Mokxi projects use a 28BYJ-48 stepper motor (1 beginner, 8 intermediate and 4 advanced). They run on Arduino Uno, Arduino Nano and ESP32 boards. Here are all of them, from “Stepper motor on pins 8 to 11” to “Pick and place”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

How to pick your first one

  • Start with “Stepper motor on pins 8 to 11”, a beginner project that needs a 28BYJ-48 stepper motor.
  • Arduino Uno runs 10 of them, Arduino Nano 1 and ESP32 1. Start on the board you have, or on an Arduino Uno if you are buying one.
  • The parts used most here are the I2C LCD (4 projects), the push button (4) and the servo motor (3). With those on hand, most of this list is open to you.
  • Before you build one on a real bench, read the 28BYJ-48 stepper and ULN2003 wiring guide for your board below. It gives every pin and the voltage notes.
Projects

13 projects ready to run

  • Stepper motor on pins 8 to 11, drawn in the Mokxi editor

    Stepper motor on pins 8 to 11

    A 28BYJ-48 on its ULN2003 board with IN1 to IN4 on pins 8 to 11: the Stepper library turns the shaft one full turn one way, then back.

    Board
    Arduino Uno R3
    Parts
    28BYJ-48 stepper and ULN2003
    Level
    Beginner
    Open in the simulator
  • Stepper dial on the analyzer, drawn in the Mokxi editor

    Stepper dial on the analyzer

    A 28BYJ-48 following a knob, with a logic analyzer on its four coil lines: the half-step sequence walking, and the capture as CSV.

    Board
    Arduino Uno R3
    Parts
    28BYJ-48 stepper and ULN2003, potentiometer, logic analyzer
    Level
    Intermediate
    Open in the simulator
  • MicroPython stepper motor on a Pico, GP21 to GP18, drawn in the Mokxi editor

    MicroPython stepper motor on a Pico, GP21 to GP18

    MicroPython on a Raspberry Pi Pico: a 28BYJ-48 stepper on a ULN2003 board, driven from GP21 to GP18, turns once one way and once back.

    Board
    Raspberry Pi Pico
    Parts
    Battery: AA, 28BYJ-48 stepper and ULN2003
    Level
    Intermediate
    Open in the simulator
  • Remote stepper, drawn in the Mokxi editor

    Remote stepper

    An IR receiver on pin 12 and a 28BYJ-48 on its ULN2003 board: VOL+ turns the shaft a quarter turn and VOL- turns it back.

    Board
    Arduino Uno R3
    Parts
    28BYJ-48 stepper and ULN2003, IR receiver and remote, IR remote
    Level
    Intermediate
    Open in the simulator
  • Knob stepper, drawn in the Mokxi editor

    Knob stepper

    A rotary encoder on pins 2, 3 and 4 steers a 28BYJ-48 click for click; press the knob and the shaft goes home.

    Board
    Arduino Uno R3
    Parts
    28BYJ-48 stepper and ULN2003, KY-040 rotary encoder
    Level
    Intermediate
    Open in the simulator
  • MicroPython stepper motor on a ULN2003 board, drawn in the Mokxi editor

    MicroPython stepper motor on a ULN2003 board

    MicroPython on an ESP32: a 28BYJ-48 stepper on its ULN2003 board, IN1 to IN4 on GPIO 14, 27, 26 and 25, turns once one way and once back.

    Board
    ESP32-DevKitC V4
    Parts
    28BYJ-48 stepper and ULN2003
    Level
    Intermediate
    Open in the simulator
  • Stepper follows a knob (pins 2 to 5), drawn in the Mokxi editor

    Stepper follows a knob (pins 2 to 5)

    A 28BYJ-48 on its ULN2003 board with IN1 to IN4 on pins 2 to 5 follows a potentiometer on A0: turn the knob and the shaft turns to match.

    Board
    Arduino Uno R3
    Parts
    28BYJ-48 stepper and ULN2003, potentiometer
    Level
    Intermediate
    Open in the simulator
  • Animated diorama: DFPlayer sound + stepper, drawn in the Mokxi editor

    Animated diorama: DFPlayer sound + stepper

    A button plays a C-3PO line on a DFPlayer Mini while a 28BYJ-48 turns R2-D2’s dome.

    Board
    Arduino Nano
    Parts
    DFPlayer Mini MP3 module, resistor, push button, 8 ohm speaker, 28BYJ-48 stepper and ULN2003
    Level
    Intermediate
    Open in the simulator
  • Stepper turntable, drawn in the Mokxi editor

    Stepper turntable

    A photo turntable on a 28BYJ-48 and its ULN2003 board with AccelStepper: press the button and the plate turns a full circle in eight stops.

    Board
    Arduino Uno R3
    Parts
    Push button, 28BYJ-48 stepper and ULN2003
    Level
    Intermediate
    Open in the simulator
  • Access control: RFID card opens a stepper door, drawn in the Mokxi editor

    Access control: RFID card opens a stepper door

    An RC522 reader (SS 10, RST 9) checks each card against the one it knows.

    Board
    Arduino Uno R3
    Parts
    MFRC522 RFID reader, 28BYJ-48 stepper and ULN2003, I2C LCD
    Level
    Advanced
    Open in the simulator
  • Satellite tracker, drawn in the Mokxi editor

    Satellite tracker

    A stepper and a servo point a small dish at a satellite on a demo pass, from a simplified circular-orbit model.

    Board
    Arduino Uno R3
    Parts
    28BYJ-48 stepper and ULN2003, servo motor, push button, resistor, LED, +2 more
    Level
    Advanced
    Open in the simulator
  • ASRS picker, drawn in the Mokxi editor

    ASRS picker

    A stepper carriage homes on a limit switch, then counts its steps to the shelf you type on a keypad.

    Board
    Arduino Uno R3
    Parts
    4x3 telephone keypad, servo motor, 28BYJ-48 stepper and ULN2003, limit switch, buzzer, +1 more
    Level
    Advanced
    Open in the simulator
  • Pick and place, drawn in the Mokxi editor

    Pick and place

    Two steppers home to their switches, then each START moves a part from the pick point to the place point: nozzle down, vacuum on, up, across, down.

    Board
    Arduino Uno R3
    Parts
    Relay module, DC motor, servo motor, 28BYJ-48 stepper and ULN2003, limit switch, +2 more
    Level
    Advanced
    Open in the simulator