Project ideas by part

Projects with a diode

17 Mokxi projects use a diode (2 beginner, 13 intermediate and 2 advanced). They run on Arduino Uno, Raspberry Pi Pico and Arduino Mega boards. Here are all of them, from “Touchless soap dispenser” to “Key matrix numpad”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

How to pick your first one

  • Start with “Touchless soap dispenser”, a beginner project that needs a touchless soap dispenser, a transistor, a resistor and 1 more part.
  • Arduino Uno runs 11 of them, Raspberry Pi Pico 2 and Arduino Mega 1. Start on the board you have, or on an Arduino Uno if you are buying one.
  • The parts used most here are the transistor (10 projects), the DC motor (7) and the LED (6). With those on hand, most of this list is open to you.
  • Before you build one on a real bench, open the diode part page for its pins and what each one does.
Projects

17 projects ready to run

  • Touchless soap dispenser, drawn in the Mokxi editor

    Touchless soap dispenser

    An FC-51 infrared obstacle sensor and a pump on a transistor: hold a hand under the spout and it pumps one dose, then waits for the hand to go away.

    Board
    Arduino Uno R3
    Parts
    Touchless soap dispenser, transistor, resistor, diode
    Level
    Beginner
    Open in the simulator
  • Motor pinwheel, drawn in the Mokxi editor

    Motor pinwheel

    Hold the button and an IRF520 MOSFET on pin 9 runs a DC motor from a 9 V battery, with a 1N4007 across the motor to catch its kick.

    Board
    Arduino Uno R3
    Parts
    Push button, resistor, MOSFET, diode, DC motor, +1 more
    Level
    Beginner
    Open in the simulator
  • Relay switches a motor, drawn in the Mokxi editor

    Relay switches a motor

    Pin 7 drives a transistor that pulls in a 5 V relay, with a diode across its coil, and the relay’s contacts run a DC motor.

    Board
    Arduino Uno R3
    Parts
    Resistor, transistor, diode, DPDT relay, DC motor, +1 more
    Level
    Intermediate
    Open in the simulator
  • MicroPython relay switches a motor: button on 15, drawn in the Mokxi editor

    MicroPython relay switches a motor: button on 15

    MicroPython on an ESP32: each press of the button on GPIO 15 flips a relay driven through an S8050 from GPIO 13, and the relay runs a DC motor.

    Board
    ESP32-DevKitC V4
    Parts
    Resistor, push button, transistor, DPDT relay, diode, +2 more
    Level
    Intermediate
    Open in the simulator
  • Pico W relay through an S8050 switches an LED, drawn in the Mokxi editor

    Pico W relay through an S8050 switches an LED

    MicroPython on a Pico W: GP15 drives an S8050 that pulls in a 5 V relay with a flyback diode, and the relay contact lights an LED, two seconds on.

    Board
    Raspberry Pi Pico W
    Parts
    DPDT relay, diode, transistor, resistor, LED
    Level
    Intermediate
    Open in the simulator
  • Electromagnet hold and drop, drawn in the Mokxi editor

    Electromagnet hold and drop

    An Uno holds a steel plate with a 12 V P20/15 electromagnet through a MOSFET on pin 9, three seconds on and two off, with a diode across the coil.

    Board
    Arduino Uno R3
    Parts
    MOSFET, diode, holding electromagnet, bench power supply
    Level
    Intermediate
    Open in the simulator
  • Music box, drawn in the Mokxi editor

    Music box

    A tune on an 8 ohm speaker through 100 ohms, a continuous-rotation servo turning the drum.

    Board
    Arduino Uno R3
    Parts
    Transistor, resistor, diode, vibration motor, 8 ohm speaker, +1 more
    Level
    Intermediate
    Open in the simulator
  • Mains to 17 V DC, drawn in the Mokxi editor

    Mains to 17 V DC

    A 230 V to 12-0-12 V mains transformer, two 1N4007s as a full-wave rectifier and 1000 uF of smoothing.

    Board
    No board
    Parts
    Signal generator, mains transformer, diode, capacitor, resistor, +2 more
    Level
    Intermediate
    Open in the simulator
  • Smart blind stick, drawn in the Mokxi editor

    Smart blind stick

    An HC-SR04 sets a buzzer and a vibration motor pulsing faster as an obstacle gets closer, and a water sensor at the tip chirps for a puddle.

    Board
    Arduino Uno R3
    Parts
    Transistor, resistor, diode, vibration motor, buzzer, +2 more
    Level
    Intermediate
    Open in the simulator
  • Solenoid tap, drawn in the Mokxi editor

    Solenoid tap

    An Uno taps a 12 V solenoid once a second through a MOSFET, with a diode across the coil to catch the kick when it lets go.

    Board
    Arduino Uno R3
    Parts
    MOSFET, diode, solenoid, bench power supply
    Level
    Intermediate
    Open in the simulator
  • MicroPython relay and motor on a Pico: a button toggles it, drawn in the Mokxi editor

    MicroPython relay and motor on a Pico: a button toggles it

    MicroPython on a Raspberry Pi Pico: each press of the button on GP15 flips a relay through a transistor on GP14, and the relay runs a DC motor.

    Board
    Raspberry Pi Pico
    Parts
    Resistor, transistor, push button, battery: AA, DPDT relay, +3 more
    Level
    Intermediate
    Open in the simulator
  • Relays reverse a motor, drawn in the Mokxi editor

    Relays reverse a motor

    Two motors turned both ways by relays: one on a two-channel board wired as an H bridge, one on a bare DPDT relay switched by a transistor.

    Board
    Arduino Uno R3
    Parts
    Resistor, transistor, diode, DPDT relay, DC motor, +1 more
    Level
    Intermediate
    Open in the simulator
  • Leak detector with shutoff valve, drawn in the Mokxi editor

    Leak detector with shutoff valve

    A teaching model: a YF-S201 flow sensor and an EEPROM totalizer watch for water that never stops or a trickle nobody is using.

    Board
    Arduino Uno R3
    Parts
    Water flow sensor, solenoid, bench power supply, MOSFET, diode, +5 more
    Level
    Intermediate
    Open in the simulator
  • Relay switches a motor: button on 12, relay on 9, drawn in the Mokxi editor

    Relay switches a motor: button on 12, relay on 9

    Each press of the button on pin 12 flips a relay, driven from pin 9 through an NPN transistor with a diode across its coil.

    Board
    Arduino Uno R3
    Parts
    Push button, resistor, transistor, DPDT relay, diode, +3 more
    Level
    Intermediate
    Open in the simulator
  • Motor on a transistor, drawn in the Mokxi editor

    Motor on a transistor

    A DC motor driven from pin 9 through a 2N2222, with a flyback diode across it. The PWM ramps up and down and the shaft follows.

    Board
    Arduino Uno R3
    Parts
    Transistor, resistor, diode, DC motor
    Level
    Intermediate
    Open in the simulator
  • Pinball table, drawn in the Mokxi editor

    Pinball table

    A table you can play on a Mega: flippers, pop bumpers on a kicker solenoid, targets, a drain beam and a plunger, with a four-digit score.

    Board
    Arduino Mega 2560 R3
    Parts
    TM1637 four-digit display, WS2812 NeoPixel LEDs, pinball table, MOSFET, diode, +3 more
    Level
    Advanced
    Open in the simulator
  • Key matrix numpad, drawn in the Mokxi editor

    Key matrix numpad

    Twelve switches in a 4 x 3 matrix with a diode on every key, three layers, an encoder and per-key RGB on a Pro Micro, typed as a USB keyboard.

    Board
    SparkFun Pro Micro
    Parts
    Push button, diode, KY-040 rotary encoder, WS2812 NeoPixel LEDs
    Level
    Advanced
    Open in the simulator