Project ideas by part

Projects with a lamp

25 Mokxi projects use a filament lamp (8 beginner, 12 intermediate and 5 advanced). They run on Arduino Uno and ESP32 boards, and 4 need no board at all. Here are 24, from “ULN2803A switching four 12 V lamps” to “Pressure tank monitor”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

How to pick your first one

  • Start with “One cell to 12 V”, a beginner project that needs a battery: AA, an MT3608 boost converter module and a lamp.
  • Arduino Uno runs 19 of them, ESP32 2 and 4 need no board at all. Start on the board you have, or on an Arduino Uno if you are buying one.
  • The parts used most here are the LED (7 projects), the push button (6) and the slide switch (6). With those on hand, most of this list is open to you.
  • Before you build one on a real bench, open the filament lamp part page for its pins and what each one does.
Projects

24 projects of 25

  • ULN2803A switching four 12 V lamps, drawn in the Mokxi editor

    ULN2803A switching four 12 V lamps

    Four slide switches on a ULN2803A's inputs, four 12 V lamps on its outputs: each channel sinks its lamp to about 0.87 V.

    Board
    No board
    Parts
    ULN2803A Darlington array, slide switch, filament lamp
    Level
    Beginner
    Open in the simulator
  • One cell to 12 V, drawn in the Mokxi editor

    One cell to 12 V

    An 18650 cell into an MT3608 boost module set to 12 V lights a 12 V lamp, and keeps it lit at 12 V as the cell runs down.

    Board
    No board
    Parts
    Battery: AA, MT3608 boost converter module, filament lamp
    Level
    Beginner
    Open in the simulator
  • A 3S LiPo to 5 V with an MP1584, drawn in the Mokxi editor

    A 3S LiPo to 5 V with an MP1584

    A three-cell LiPo into an MP1584 buck module set to 5 V lights a 6 V lamp, and the output holds 5 V as the pack runs down.

    Board
    No board
    Parts
    Battery: AA, MP1584 mini buck converter, filament lamp
    Level
    Beginner
    Open in the simulator
  • IR remote control relay module, drawn in the Mokxi editor

    IR remote control relay module

    IRremote and a 21-key handset: keys 1 to 4 toggle the four channels of a relay board, each switching a 12 V lamp, and 0 turns them all off.

    Board
    Arduino Uno R3
    Parts
    IR remote, IR receiver and remote, four-channel relay board, DC jack and adapter, filament lamp
    Level
    Beginner
    Open in the simulator
  • Bluetooth home automation with relays, drawn in the Mokxi editor

    Bluetooth home automation with relays

    An HC-05 and a four-relay board: send 1 to 4 from the module’s box, as a phone app does, and that lamp toggles; A and a switch them all, ?

    Board
    Arduino Uno R3
    Parts
    HC-05 Bluetooth module, resistor, four-channel relay board, DC jack and adapter, filament lamp
    Level
    Beginner
    Open in the simulator
  • PIR motion light with a relay, drawn in the Mokxi editor

    PIR motion light with a relay

    After dark, an HC-SR501 PIR switches a 12 V lamp on through a relay, and it goes off 20 s after the last movement; a light sensor keeps it off by day.

    Board
    Arduino Uno R3
    Parts
    PIR motion sensor, photoresistor module, relay module, DC jack and adapter, filament lamp
    Level
    Beginner
    Open in the simulator
  • 12 V lamp dimmer with a MOSFET module, drawn in the Mokxi editor

    12 V lamp dimmer with a MOSFET module

    A knob on A0 sets the PWM on pin 9, and a D4184 MOSFET module dims a 12 V lamp on a wall adapter with it: the pin switches the gates, not the lamp.

    Board
    Arduino Uno R3
    Parts
    Potentiometer, D4184 MOSFET module, DC jack and adapter, filament lamp
    Level
    Beginner
    Open in the simulator
  • Lamp power meter, drawn in the Mokxi editor

    Lamp power meter

    A MAX471 board in a 6 V lamp’s supply lead: the volts, milliamps and milliwatts on a 16x2 I2C LCD, and the surge a cold filament draws.

    Board
    Arduino Uno R3
    Parts
    Current and voltage sensor, push button, filament lamp, bench power supply, I2C LCD
    Level
    Beginner
    Open in the simulator
  • Two AC lamps on an SSR board, drawn in the Mokxi editor

    Two AC lamps on an SSR board

    A two-channel G3MB-202P solid-state relay board switches two 12 V AC lamps from an Uno: each channel is on while its pin is LOW.

    Board
    Arduino Uno R3
    Parts
    SSR board, signal generator, filament lamp
    Level
    Intermediate
    Open in the simulator
  • Energy meter, drawn in the Mokxi editor

    Energy meter

    An INA228 on a 12 V load adds up the joules and coulombs through its shunt, and an OPT3001 reads the light falling on the panel that would charge it.

    Board
    Arduino Uno R3
    Parts
    Power and energy monitor, filament lamp, ambient light
    Level
    Intermediate
    Open in the simulator
  • Solid-state relay on 24 V AC, drawn in the Mokxi editor

    Solid-state relay on 24 V AC

    An SSR-25DA on pin 7 switches two 12 V lamps on 24 V AC, on two seconds and off two: it turns on at a zero of the AC and off at the next current zero.

    Board
    Arduino Uno R3
    Parts
    Solid-state relay, signal generator, filament lamp
    Level
    Intermediate
    Open in the simulator
  • ESP32 async web server: BME280, slider and relay, drawn in the Mokxi editor

    ESP32 async web server: BME280, slider and relay

    ESPAsyncWebServer serves a page with BME280 temperature, humidity and pressure, a slider that dims an LED and a button that switches a relay.

    Board
    ESP32 DevKit V1
    Parts
    BME280 weather sensor, resistor, LED, relay module, DC jack and adapter, +1 more
    Level
    Intermediate
    Open in the simulator
  • Two rails, drawn in the Mokxi editor

    Two rails

    An INA226 on a 12 V load and an INA3221 on a 5 V one: each rail’s voltage and current, and the power, on one I2C bus.

    Board
    Arduino Uno R3
    Parts
    Power monitor, filament lamp, three-channel current monitor
    Level
    Intermediate
    Open in the simulator
  • Solar battery monitor with an INA3221, drawn in the Mokxi editor

    Solar battery monitor with an INA3221

    One INA3221 reads a solar panel, an 18650 and its load on three channels, and a 20x4 LCD shows volts, currents and whether the cell is charging.

    Board
    Arduino Uno R3
    Parts
    Three-channel current monitor, solar panel, li-ion charger, battery: AA, filament lamp, +1 more
    Level
    Intermediate
    Open in the simulator
  • LM393 night light with a ULN2003A, drawn in the Mokxi editor

    LM393 night light with a ULN2003A

    An LM393 compares an LDR with a knob, its open-collector output pulled up by 10 k.

    Board
    No board
    Parts
    Photoresistor, resistor, potentiometer, LM393 dual comparator, ULN2003A Darlington array, +1 more
    Level
    Intermediate
    Open in the simulator
  • Lamp inrush, drawn in the Mokxi editor

    Lamp inrush

    An Uno switches a 6 V filament lamp with a MOSFET and samples its current every millisecond: the surge of a cold filament.

    Board
    Arduino Uno R3
    Parts
    MOSFET, resistor, filament lamp, battery: AA
    Level
    Intermediate
    Open in the simulator
  • Bidirectional visitor counter, drawn in the Mokxi editor

    Bidirectional visitor counter

    Two IR sensors at a doorway tell people coming in from going out, an I2C LCD shows IN, OUT and inside, and a relay lights the room while anyone is in.

    Board
    Arduino Uno R3
    Parts
    FC-51 IR obstacle sensor, relay module, DC jack and adapter, filament lamp, I2C LCD
    Level
    Intermediate
    Open in the simulator
  • Four AC lamps on an IR remote SSR board, drawn in the Mokxi editor

    Four AC lamps on an IR remote SSR board

    Keys 1 to 4 on an IR handset toggle the four channels of a G3MB-202P solid-state relay board, each switching a 12 V AC lamp; 0 turns them all off.

    Board
    Arduino Uno R3
    Parts
    IR remote, IR receiver and remote, SSR board, signal generator, filament lamp
    Level
    Intermediate
    Open in the simulator
  • Turn signals and hazard flasher, drawn in the Mokxi editor

    Turn signals and hazard flasher

    Left, right and hazard buttons flash two 12 V bulbs a side through a relay board at 90 a minute.

    Board
    Arduino Uno R3
    Parts
    Push button, resistor, LED, two-channel relay board, INA219 current monitor, +3 more
    Level
    Intermediate
    Open in the simulator
  • Smart home hub, drawn in the Mokxi editor

    Smart home hub

    An ESP32-C3 web dashboard that switches a lamp and a fan through relays, dims a porch light, reads temperature, humidity and motion.

    Board
    ESP32-C3-DevKitM-1
    Parts
    Two-channel relay board, filament lamp, DC motor, LED, resistor, +4 more
    Level
    Advanced
    Open in the simulator
  • Heated bed PID, drawn in the Mokxi editor

    Heated bed PID

    A 100k thermistor, a MOSFET heater and a PID loop holding a modeled bed at its target.

    Board
    Arduino Uno R3
    Parts
    Resistor, 10k NTC thermistor, MOSFET, filament lamp, slide switch, +1 more
    Level
    Advanced
    Open in the simulator
  • Water heater thermostat, drawn in the Mokxi editor

    Water heater thermostat

    A thermistor, a setpoint knob and an SSR-switched lamp for the element: an 8 F hysteresis band plus a latched high-limit cutout.

    Board
    Arduino Uno R3
    Parts
    10k NTC thermistor, resistor, potentiometer, push button, LED, +3 more
    Level
    Advanced
    Open in the simulator
  • Generator transfer switch, drawn in the Mokxi editor

    Generator transfer switch

    The control logic of an automatic transfer switch with low-voltage stand-ins: two interlocked contactors that never both close.

    Board
    Arduino Uno R3
    Parts
    Push button, resistor, LED, transistor, slide switch, +2 more
    Level
    Advanced
    Open in the simulator
  • Pressure tank monitor, drawn in the Mokxi editor

    Pressure tank monitor

    A pressure transducer and a pump relay run a 40/60 or 30/50 psi cut-in and cut-out, count pump cycles and run time, and flag short cycling.

    Board
    Arduino Uno R3
    Parts
    0.5 to 4.5 V pressure sender, relay module, filament lamp, slide switch, push button, +2 more
    Level
    Advanced
    Open in the simulator