Project ideas by part

Projects with a DS18B20 sensor

7 Mokxi projects use a DS18B20 sensor (1 beginner, 2 intermediate and 4 advanced). They run on Arduino Uno boards. Here are all of them, from “DS18B20 temperature sensor on pin 2” to “HVAC thermostat”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.

First project

How to pick your first one

  • Start with “DS18B20 temperature sensor on pin 2”, a beginner project that needs a DS18B20 sensor.
  • All of them run on an Arduino Uno, so that is the one board you need.
  • The parts used most here are the LED (3 projects), the slide switch (2) and the DS3231 real-time clock (1). With those on hand, most of this list is open to you.
  • Before you build one on a real bench, read the DS18B20 temperature sensor wiring guide for your board below. It gives every pin and the voltage notes.
Projects

7 projects ready to run

  • DS18B20 temperature sensor on pin 2, drawn in the Mokxi editor

    DS18B20 temperature sensor on pin 2

    A DS18B20 on pin 2, with a 4.7k pull-up on its data line, measures the temperature over one wire; the Dallas library reads it once a second.

    Board
    Arduino Uno R3
    Parts
    DS18B20 temperature sensor
    Level
    Beginner
    Open in the simulator
  • Thermometers on one wire, drawn in the Mokxi editor

    Thermometers on one wire

    Two DS18B20s on pin 2 and one 4k7 pull-up. The 1-Wire search finds both by their serial numbers, and each is then read by name.

    Board
    Arduino Uno R3
    Parts
    DS18B20 temperature sensor, resistor
    Level
    Intermediate
    Open in the simulator
  • Temperature data logger with an SD card, drawn in the Mokxi editor

    Temperature data logger with an SD card

    A DS18B20, a DS3231 clock and a microSD card: every 5 seconds a dated temperature line goes into TEMPLOG.CSV, ready to open in a spreadsheet.

    Board
    Arduino Uno R3
    Parts
    MicroSD card module, resistor, LED, DS18B20 temperature sensor, DS3231 real-time clock
    Level
    Intermediate
    Open in the simulator
  • nRF24L01 sensor network with RF24Network, drawn in the Mokxi editor

    nRF24L01 sensor network with RF24Network

    Two nRF24L01 sensor nodes send DS18B20 temperatures to a base node every 2 seconds, and the base shows each one on an LCD.

    Board
    Arduino Uno R3
    Parts
    NRF24L01+ 2.4 GHz radio, I2C LCD, DS18B20 temperature sensor
    Level
    Advanced
    Open in the simulator
  • Deep-sea dive computer, drawn in the Mokxi editor

    Deep-sea dive computer

    A pressure transducer turned into depth (about 1 atm per 10 m of sea water), a DS18B20 water probe.

    Board
    Arduino Uno R3
    Parts
    0.5 to 4.5 V pressure sender, DS18B20 temperature sensor, resistor, SSD1306 OLED display, piezo speaker
    Level
    Advanced
    Open in the simulator
  • Delta-T monitor, drawn in the Mokxi editor

    Delta-T monitor

    Two DS18B20s on one wire read supply and return air: the drop across the coil is judged only while the cooling call runs and has settled.

    Board
    Arduino Uno R3
    Parts
    DS18B20 temperature sensor, float switch, relay module, slide switch, resistor, +1 more
    Level
    Advanced
    Open in the simulator
  • HVAC thermostat, drawn in the Mokxi editor

    HVAC thermostat

    A two-stage heat and cool thermostat on an Uno: W1, W2, Y1, Y2 and G on LEDs, compressor minimum on and off times.

    Board
    Arduino Uno R3
    Parts
    DS18B20 temperature sensor, slide switch, potentiometer, resistor, LED
    Level
    Advanced
    Open in the simulator