Wiring guide

How to wire a DS18B20 to an Arduino Nano

To wire a DS18B20 to an Arduino Nano, connect VDD to 5V, DQ to pin 2 and GND to GND. The sensor and its 4.7 kilohm pull-up both go to 5 V, so the one data line idles at the board’s own level. The sketch below uses the DallasTemperature (DallasTemperature.h) library. It counts the sensors on the one-wire bus and prints the temperature.

  • 5 V logic
  • Library: DallasTemperature.h
  • 3 wires, 1 helper parts
Arduino Nano · DS18B20live0.000 s 0.00x
Click to open it in the editor
The circuit itself, running on the simulator with the sketch below. Press what can be pressed; click anything else to open it in the editor.
Pin to pin

DS18B20 to Arduino Nano wiring table

Every wire in the circuit above, with the part’s pin names and the board’s own labels. The wire colors are the ones the circuit uses; on a real bench any colors work.

DS18B20 pinArduino Nano pinWire colorWhy
VDD (right leg)5VredThe DS18B20 runs from 3.0 to 5.5 V.
DQ (middle leg)pin 2amberThe one data wire, shared by every sensor on the bus.
GND (left leg)GNDblueGround, with the flat face toward you.
4.7 k resistorDQ to 5Vn/aThe pull-up the bus needs: the sensor only ever pulls the line low.

Helper parts

The extra parts in the circuit above, and where their wires go:

FromToWire color
R1 (4.7 kΩ) pin 1DQamber
R1 (4.7 kΩ) pin 2VDDred
Voltage

Power and logic levels for DS18B20 and Arduino Nano

Logic level

The Arduino Nano’s pins are 5 V logic. A 5 V part can drive them directly; a part whose signal pins are limited to 3.3 V needs a level shifter.

Supply

The DS18B20 takes 5 V from 5V. That is the Arduino Nano’s 5 V rail, so the part shares the current the board can supply.

This pair

On the Arduino Nano the sensor and its pull-up go to 5V. A long cable may need a stronger pull-up, 2.2 k, to keep the edges sharp.

Pins to leave alone

A6 and A7 are analog only: pinMode(A6, OUTPUT) does nothing and digitalRead(A7) is not there to call. D0 and D1 are the USB serial port.

The sketch

The working code for the Arduino Nano

Library: DallasTemperature (DallasTemperature.h). This is the sketch the circuit above runs.

DS18B20 on Arduino Nano pin 2
#include <OneWire.h>
#include <DallasTemperature.h>

const int ONE_WIRE_PIN = 2;   // DQ, pin 2, with 4.7 k to 5V

OneWire oneWire(ONE_WIRE_PIN);
DallasTemperature sensors(&oneWire);

void setup() {
  Serial.begin(9600);
  sensors.begin();
  Serial.print("Sensors found: ");
  Serial.println(sensors.getDeviceCount());
}

void loop() {
  sensors.requestTemperatures();          // start a conversion on every sensor
  float celsius = sensors.getTempCByIndex(0);
  if (celsius == DEVICE_DISCONNECTED_C) {
    Serial.println("Sensor not found");
  } else {
    Serial.print("Temperature: ");
    Serial.print(celsius, 2);
    Serial.println(" C");
  }
  delay(1000);
}
Output

What you should see

Open the serial monitor at 9600 baud. The sketch prints how many sensors it found and then the temperature in degrees C once a reading is ready; the sensor starts at 22 degrees.

A reading of -127 C, or no sensor found, means the data line has no pull-up or is on the wrong pin.

The serial monitor prints this, recorded from the circuit above left at its defaults:

Sensors found: 1
Temperature: 22.00 C
Pitfalls

Common mistakes wiring a DS18B20 to an Arduino Nano

No pull-up resistor

Without the 4.7 k from DQ to the supply, the line never goes high, sensors.begin() finds nothing and every reading is -127. In the simulator, delete the resistor and you get exactly that.

The sensor in backwards

With the flat side facing you, the legs are GND, DQ, VDD from left to right. Reversed, a real DS18B20 gets hot fast. Waterproof probes use red for VDD, black for GND and yellow or white for DQ.

Picking A6 or A7

A6 and A7 look like the other analog pins but are inputs to the ADC and nothing else. the 1-Wire bus on either of them never sees a digital level. Any of D2 to D13 or A0 to A5 works.

Build your own DS18B20 project

Open this circuit in the editor, change the wiring or the code, and keep your version in a free account.