مازج ألوان RGB على Arduino Uno
RGB LED على ثلاثة أطراف PWM، كل منها عبر مقاومته: يجعله analogWrite يتدرج عبر عشرة ألوان مسماة، بينها أبيض موازَن للون الأحمر الضعيف. المشروع كله، Arduino Uno و4 قطع أخرى، يعمل هنا في متصفحك على البرنامج الثابت أدناه؛ افتحه في المحرر لتغيير التوصيل أو الكود وتشغيله مرة أخرى.
تدرّس؟ كلّف صفك به بنقرة واحدة.
مبتدئ About 15 minutes to build and run. يعمل في متصفحك. مجاني ودون حاجة إلى حساب.
تُباع القطع بنحو $32. وفي Mokxi هي مجانية.
خطوة بخطوة، مع التوصيل والأخطاء الشائعة: RGB LED في Arduino: التوصيل وكود مزج الألوان
What you'll learn
- Mixing colors with PWM on three pins
- How an RGB LED works
- Fading smoothly between two values
- Structs for named colors
- Common cathode versus common anode
- Difficulty: مبتدئ
- Time: About 15 minutes
- Board: Arduino Uno R3
- Parts: 6
كيف يعمل
An RGB LED is three LEDs under one lens. Pins 9, 10 and 11 drive the red, green and blue legs through 220 Ω resistors, and the common leg goes to ground. Your eye mixes the three into one color.
analogWrite sets how bright each one is, from 0 to 255. The sketch fades from one named color to the next over one second, holds it for one second, and prints the color name and its three numbers.
There are two whites. With all three at 255 the light looks pinkish, because red gets more current than the others. The balanced white turns red down to 170.
قائمة القطع
6 قطع، إضافةً إلى أسلاك التوصيل. تُباع بنحو $32؛ وفي Mokxi هي مجانية.
- 1 × Arduino Uno R3In Starter Kit, Claw Machine Kit, Vending Machine Kit.
- 1 × لوحة تجارب كاملة الحجم
- 1 × RGB LEDIn Starter Projects Kit.
- 3 × مقاومة، 220 ΩIn Starter Kit, Claw Machine Kit, Halloween Prop Kit.
Kits that can build it
These 12 starter kits have every part in the circuit. Each kit's page lists what else it can build.
- ELEGOO UNO R3 Super Starter Kit
- ELEGOO UNO R3 Most Complete Starter Kit
- Arduino Starter Kit
- Freenove Ultimate Starter Kit
- ELEGOO UNO R3 Basic Starter Kit
- SunFounder Starter Kit for Arduino Uno R3
- SunFounder Inventor Lab Kit
- REXQualis UNO R3 Super Starter Kit
- LAFVIN Super Starter Kit
- keyestudio Super Starter Kit
- Vilros Arduino Uno 3 Ultimate Starter Kit
- Adafruit MetroX Classic Kit
Wiring table
Every connection, pin by pin, read from the circuit itself. Each row joins the pin on the left to the pin on the right, by a jumper wire or a breadboard strip.
| القطعة والطرف | Connects to |
|---|---|
| Resistor, 220 Ω (1) pin 1 | Arduino Uno R3 pin 11 |
| Resistor, 220 Ω (2) pin 1 | Arduino Uno R3 pin 10 |
| Resistor, 220 Ω (3) pin 1 | Arduino Uno R3 pin 9 |
| RGB LED pin C | Arduino Uno R3 pin GND |
| Resistor, 220 Ω (3) pin 2 | RGB LED pin R |
| Resistor, 220 Ω (2) pin 2 | RGB LED pin G |
| Resistor, 220 Ω (1) pin 2 | RGB LED pin B |
الكود
البرنامج الثابت تمامًا كما يفتحه المحرر. غيّر سطرًا هناك واضغط «تشغيل»: يُترجَم في المتصفح.
// RGB color mixer: one RGB LED, three PWM pins, every color in between.
//
// pin 9 the red leg, through 220 ohm
// pin 10 the green leg, through 220 ohm
// pin 11 the blue leg, through 220 ohm
// the long leg (the common cathode) to GND
//
// An RGB LED is three LEDs under one lens. analogWrite() sets how bright each
// one is, from 0 (off) to 255 (full), and your eye mixes the three into one
// color. Red and green make yellow, green and blue make cyan, all three make
// white.
//
// The sketch fades from one named color to the next over one second, holds it
// for a second, and prints its name and its three numbers when it gets there.
//
// # Why there are two whites
//
// The red die needs about 1.8 V and the green and blue ones about 3 V. On the
// same 220 ohm resistors from a 5 V pin, red gets about 15 mA and the other
// two about 10, so "all three at 255" comes out pinkish. The balanced white
// turns red down to two thirds to make up for it. On a real LED you can do
// the same in code, or give red a bigger resistor.
//
// # Common anode
//
// This is a common-cathode LED: HIGH lights a color. On a common-anode LED
// the long leg goes to 5 V and LOW lights a color, so every value is flipped:
// write 255 - value instead.
const int RED_PIN = 9;
const int GREEN_PIN = 10;
const int BLUE_PIN = 11;
struct Color {
const char *name;
uint8_t r, g, b;
};
const Color COLORS[] = {
{"red", 255, 0, 0},
{"orange", 255, 40, 0},
{"yellow", 255, 160, 0},
{"green", 0, 255, 0},
{"cyan", 0, 255, 255},
{"blue", 0, 0, 255},
{"purple", 120, 0, 255},
{"magenta", 255, 0, 255},
{"white (all 255)", 255, 255, 255},
{"balanced white", 170, 255, 255},
};
const int COUNT = sizeof(COLORS) / sizeof(COLORS[0]);
const int FADE_STEPS = 50;
const int STEP_MS = 20;
const int HOLD_MS = 1000;
int r = 0, g = 0, b = 0;
void show(int red, int green, int blue) {
analogWrite(RED_PIN, red);
analogWrite(GREEN_PIN, green);
analogWrite(BLUE_PIN, blue);
}
void fadeTo(const Color &c) {
for (int step = 1; step <= FADE_STEPS; step++) {
show(r + (c.r - r) * step / FADE_STEPS,
g + (c.g - g) * step / FADE_STEPS,
b + (c.b - b) * step / FADE_STEPS);
delay(STEP_MS);
}
r = c.r;
g = c.g;
b = c.b;
}
void setup() {
pinMode(RED_PIN, OUTPUT);
pinMode(GREEN_PIN, OUTPUT);
pinMode(BLUE_PIN, OUTPUT);
Serial.begin(115200);
Serial.println("Mokxi Uno: RGB color mixer");
}
void loop() {
for (int i = 0; i < COUNT; i++) {
fadeTo(COLORS[i]);
Serial.print(COLORS[i].name);
Serial.print(": ");
Serial.print(COLORS[i].r);
Serial.print(", ");
Serial.print(COLORS[i].g);
Serial.print(", ");
Serial.println(COLORS[i].b);
delay(HOLD_MS);
}
}
Code walkthrough
The key functions of the sketch, and what each one does.
show sketch.ino
Writes three brightness values to the red, green and blue pins with analogWrite. Everything else in the sketch goes through it.
void show(int red, int green, int blue) {
analogWrite(RED_PIN, red);
analogWrite(GREEN_PIN, green);
analogWrite(BLUE_PIN, blue);
}fadeTo sketch.ino
Moves from the current color to a new one in FADE_STEPS steps of STEP_MS each. At each step, it works out a point part of the way between the old and new value for each color. At the end it stores the new color in r, g and b.
void fadeTo(const Color &c) {
for (int step = 1; step <= FADE_STEPS; step++) {
show(r + (c.r - r) * step / FADE_STEPS,
g + (c.g - g) * step / FADE_STEPS,
b + (c.b - b) * step / FADE_STEPS);
delay(STEP_MS);
}
r = c.r;
g = c.g;
b = c.b;
}loop sketch.ino
Goes through the COLORS list. For each color it fades to it, prints the name and its three numbers, then holds for HOLD_MS.
void loop() {
for (int i = 0; i < COUNT; i++) {
fadeTo(COLORS[i]);
Serial.print(COLORS[i].name);
Serial.print(": ");
Serial.print(COLORS[i].r);
Serial.print(", ");
Serial.print(COLORS[i].g);
Serial.print(", ");
Serial.println(COLORS[i].b);
delay(HOLD_MS);
}
}Troubleshooting
The usual mistakes with this circuit, and the fix for each.
- The colors are wrong, such as red showing as blue This project
Red is on pin 9, green on 10 and blue on 11. Check each resistor goes to the matching LED leg. - Colors look inverted, or the LED is bright when it should be off This project
You may have a common anode LED. Connect its common leg to 5 V and write 255 minus each value. - The colors are wrong or one color never lights. RGB LED
Check whether your LED is common cathode (shared leg to ground) or common anode (shared leg to 5 V). Common anode works backwards: LOW turns a color on. - One color is much brighter than the others, or the LED runs too hot. RGB LED
Use one resistor per color leg, never one for the shared leg. Typical values are 220 ohm for red and 100 to 150 ohm for green and blue on 5 V. - The LED is dim, burns out, or the pin reads wrong because the resistor value is off. مقاومة
Read the color bands again. A 220 ohm to 330 ohm resistor suits a typical LED on 5 V. 10k is a common pull-up or pull-down value. Check with a multimeter if unsure. - A pull-up or pull-down resistor is missing, so the input floats and reads random values. مقاومة
Tie the input to 5 V or ground through about 10k. Or use INPUT_PULLUP and wire the switch to ground. - Upload fails or nothing runs after wiring pins 0 and 1 to a module. Arduino Uno R3
Pins 0 and 1 are the USB serial port. Move the module to other pins, or unplug it while uploading. Also check the right board is selected. - Pins misbehave or the board resets when you power motors or servos from it. Arduino Uno R3
Each I/O pin gives about 20 mA, 40 mA max. Power motors and servos from their own supply and join its ground to the Uno's GND.
غيّره واحتفظ به
افتحه في المحرر، وغيّر الدائرة أو الكود، واحتفظ بنسختك في حساب مجاني.