How to wire a BMP280 to an Arduino Nano
To wire a BMP280 to an Arduino Nano, connect VIN to 3.3V, GND to GND, SCL to pin A5 and SDA to pin A4. The common breakout has no regulator, so power it from 3.3 V, not 5 V; its pull-ups then go to 3.3 V, which the board reads as high. The sketch below uses the Adafruit BMP280 (Adafruit_BMP280.h) library. It prints the temperature, the pressure and an altitude estimate.
- 5 V logic
- Library: Adafruit_BMP280.h
- 4 wires
BMP280 to Arduino Nano wiring table
Every wire in the circuit above, with the part’s pin names and the board’s own labels. The wire colors are the ones the circuit uses; on a real bench any colors work.
| BMP280 pin | Arduino Nano pin | Wire color | Why |
|---|---|---|---|
| VIN | 3.3V | red | The BMP280 chip is a 3.3 V part; many breakouts have no regulator. |
| GND | GND | blue | Common ground. |
| SCL | pin A5 | cyan | I2C clock. |
| SDA | pin A4 | violet | I2C data. |
Power and logic levels for BMP280 and Arduino Nano
Logic level
The Arduino Nano’s pins are 5 V logic. A 5 V part can drive them directly; a part whose signal pins are limited to 3.3 V needs a level shifter.
This pair
The Nano has the Uno’s chip, so I2C is A4 (SDA) and A5 (SCL), on the analog side of the board next to A6 and A7. The common purple BMP280 breakout has no regulator, so it runs from the Arduino Nano’s 3.3V pin, not 5V. Its I2C pull-ups then go to 3.3 V, which the ATmega328P reads as high.
Pins to leave alone
A6 and A7 are analog only: pinMode(A6, OUTPUT) does nothing and digitalRead(A7) is not there to call. D0 and D1 are the USB serial port.
The working code for the Arduino Nano
Library: Adafruit BMP280 (Adafruit_BMP280.h). This is the sketch the circuit above runs.
#include <Wire.h>
#include <Adafruit_BMP280.h>
Adafruit_BMP280 bmp; // on I2C: SDA pin A4, SCL pin A5
void setup() {
Serial.begin(9600);
if (!bmp.begin(0x76)) {
Serial.println("No BMP280 at 0x76");
for (;;) {}
}
Serial.println("BMP280 found");
}
void loop() {
Serial.print("Temperature: ");
Serial.print(bmp.readTemperature(), 1);
Serial.print(" C Pressure: ");
Serial.print(bmp.readPressure() / 100.0F, 1);
Serial.print(" hPa Altitude: ");
Serial.print(bmp.readAltitude(1013.25), 0);
Serial.println(" m");
delay(1000);
}
What you should see
Open the serial monitor at 9600 baud. The sketch prints BMP280 found and then a line with the temperature in degrees C, the pressure in hectopascals and the altitude. The sensor starts at 22 degrees C and about 1013 hPa.
If it prints that no sensor was found, the address is the first thing to check: this circuit answers at 0x76, and some breakouts use 0x77.
The serial monitor prints this, recorded from the circuit above left at its defaults:
BMP280 found
Temperature: 22.0 C Pressure: 1013.3 hPa Altitude: -0 mCommon mistakes wiring a BMP280 to an Arduino Nano
The wrong address
Adafruit’s own board answers at 0x77, the cheap purple ones at 0x76, and bmp.begin() with no argument tries 0x77. If it fails, try the other address before suspecting the wiring.
Powering a bare breakout from 5V
The six-pin purple board has no regulator, so 5V goes straight to a chip rated for 3.6 V. Use the Arduino Nano’s 3.3V pin, as in the circuit above.
Confusing it with a BME280
The BME280 looks the same and adds humidity. A BMP280 reports a chip ID of 0x58, a BME280 0x60, and each library refuses the other. If begin() fails at both addresses, check which chip you have.
Build your own BMP280 project
Open this circuit in the editor, change the wiring or the code, and keep your version in a free account.