How to wire a servo to an Arduino Nano
To wire a servo to an Arduino Nano, connect GND to GND, VCC to 5V and PWM to pin 9. The Arduino Nano is a 5 V board, so the servo’s power and signal are both 5 V and nothing needs shifting. The sketch below uses the Servo (Servo.h) library. It sweeps the horn from 0 to 180 degrees and back, printing a line at each end.
- 5 V logic
- Library: Servo.h
- 3 wires
Servo to Arduino Nano wiring table
Every wire in the circuit above, with the part’s pin names and the board’s own labels. The wire colors are the ones the circuit uses; on a real bench any colors work.
| Servo pin | Arduino Nano pin | Wire color | Why |
|---|---|---|---|
| Brown (GND) | GND | blue | The signal is measured against this, so it must be shared with the board. |
| Red (V+) | 5V | red | An SG90 runs from 4.8 to 6 V. |
| Orange (signal) | pin 9 | amber | Any digital pin works with the Servo library. |
Power and logic levels for servo and Arduino Nano
Logic level
The Arduino Nano’s pins are 5 V logic. A 5 V part can drive them directly; a part whose signal pins are limited to 3.3 V needs a level shifter.
Supply
The servo takes 5 V from 5V. That is the Arduino Nano’s 5 V rail, so the part shares the current the board can supply.
This pair
The Arduino Nano’s 5V pin can run one unloaded SG90. Under load a servo draws spikes of several hundred milliamps that reset the board, so a real project gives it its own 5 V supply with the grounds joined.
Pins to leave alone
A6 and A7 are analog only: pinMode(A6, OUTPUT) does nothing and digitalRead(A7) is not there to call. D0 and D1 are the USB serial port.
The working code for the Arduino Nano
Library: Servo (Servo.h). This is the sketch the circuit above runs.
#include <Servo.h>
const int SERVO_PIN = 9; // signal, pin 9
Servo servo;
void setup() {
Serial.begin(9600);
servo.attach(SERVO_PIN); // 544 to 2400 us, 50 times a second
Serial.println("Sweeping");
}
void loop() {
for (int angle = 0; angle <= 180; angle += 2) {
servo.write(angle);
delay(15);
}
Serial.println("at 180");
for (int angle = 180; angle >= 0; angle -= 2) {
servo.write(angle);
delay(15);
}
Serial.println("back at 0");
}
What you should see
The servo horn turns from 0 to 180 degrees in about 1.4 seconds and then back. The serial monitor, at 9600 baud, prints Sweeping once, then at 180 at the top of each sweep and back at 0 at the bottom.
A servo that buzzes or does not move is almost always a missing common ground or a supply that sags under load.
The serial monitor prints this, recorded from the circuit above running for two and a half seconds:
Sweeping
at 180Common mistakes wiring a servo to an Arduino Nano
Running a loaded servo from the 5V pin
One servo moving a light arm is fine. Two, or one lifting something, pull the 5 V rail down far enough to reset the board, which looks like a sketch that restarts at random. Give servos their own supply and join the grounds.
Forgetting the common ground
With the servo on a separate supply and only the signal wire to the board, the servo has nothing to measure the pulse against and twitches at random. Connect the supply’s ground to the board’s GND.
Losing PWM on pins 9 and 10
On the ATmega328P the Servo library takes Timer1, so analogWrite() on pins 9 and 10 stops working once a servo is attached. Move the LED you were dimming to another PWM pin.
Build your own servo project
Open this circuit in the editor, change the wiring or the code, and keep your version in a free account.