Wiring guide

How to wire a BME280 to an Arduino Nano

To wire a BME280 to an Arduino Nano, connect VIN to 3.3V, GND to GND, SCL to pin A5 and SDA to pin A4. The common breakout has no regulator, so power it from 3.3 V, not 5 V; its pull-ups then go to 3.3 V, which the board reads as high. The sketch below uses the Adafruit BME280 (Adafruit_BME280.h) library. It prints the temperature, the humidity and the pressure.

  • 5 V logic
  • Library: Adafruit_BME280.h
  • 4 wires
Arduino Nano · BME280live0.000 s 0.00x
Click to open it in the editor
The circuit itself, running on the simulator with the sketch below. Press what can be pressed; click anything else to open it in the editor.
Pin to pin

BME280 to Arduino Nano wiring table

Every wire in the circuit above, with the part’s pin names and the board’s own labels. The wire colors are the ones the circuit uses; on a real bench any colors work.

BME280 pinArduino Nano pinWire colorWhy
VIN3.3VredThe BME280 chip is a 3.3 V part; many breakouts have no regulator.
GNDGNDblueCommon ground.
SCLpin A5cyanI2C clock.
SDApin A4violetI2C data.
Voltage

Power and logic levels for BME280 and Arduino Nano

Logic level

The Arduino Nano’s pins are 5 V logic. A 5 V part can drive them directly; a part whose signal pins are limited to 3.3 V needs a level shifter.

This pair

The Nano has the Uno’s chip, so I2C is A4 (SDA) and A5 (SCL), on the analog side of the board next to A6 and A7. The common purple BME280 breakout has no regulator, so it runs from the Arduino Nano’s 3.3V pin, not 5V.

Pins to leave alone

A6 and A7 are analog only: pinMode(A6, OUTPUT) does nothing and digitalRead(A7) is not there to call. D0 and D1 are the USB serial port.

The sketch

The working code for the Arduino Nano

Library: Adafruit BME280 (Adafruit_BME280.h). This is the sketch the circuit above runs.

BME280 on Arduino Nano I2C
#include <Wire.h>
#include <Adafruit_Sensor.h>
#include <Adafruit_BME280.h>

Adafruit_BME280 bme;   // on I2C: SDA pin A4, SCL pin A5

void setup() {
  Serial.begin(9600);
  if (!bme.begin(0x76)) {
    Serial.println("No BME280 at 0x76");
    for (;;) {}
  }
  Serial.println("BME280 found");
}

void loop() {
  Serial.print("Temperature: ");
  Serial.print(bme.readTemperature(), 1);
  Serial.print(" C  Humidity: ");
  Serial.print(bme.readHumidity(), 1);
  Serial.print(" %  Pressure: ");
  Serial.print(bme.readPressure() / 100.0F, 1);
  Serial.println(" hPa");
  delay(1000);
}
Output

What you should see

Open the serial monitor at 9600 baud. The sketch prints BME280 found and then a line with the temperature in degrees C, the humidity in percent and the pressure in hectopascals.

The BME280 is the BMP280 plus a humidity sensor; the two look alike, and a BMP280 sold as a BME280 reads no humidity.

The serial monitor prints this, recorded from the circuit above left at its defaults:

BME280 found
Temperature: 22.0 C  Humidity: 50.0 %  Pressure: 1013.3 hPa
Pitfalls

Common mistakes wiring a BME280 to an Arduino Nano

The wrong address

Adafruit’s board answers at 0x77, the cheap purple ones at 0x76, and bme.begin() with no argument tries 0x77. If it fails, try the other address before suspecting the wiring.

Using a BMP280 library

A BMP280 has no humidity and a different chip ID (0x58 against 0x60). Adafruit_BMP280 refuses a BME280 and the reverse, so match the library to the chip printed on the module.

Powering a bare breakout from 5V

A module with no regulator sends 5V straight to a chip rated for 3.6 V. Use the Arduino Nano’s 3.3V pin, as in the circuit above.

Build your own BME280 project

Open this circuit in the editor, change the wiring or the code, and keep your version in a free account.