How to wire a 4x4 keypad to an Arduino Nano
To wire a 4x4 keypad to an Arduino Nano, connect R1, R2, R3, R4 to pin 9, pin 8, pin 7, pin 6; and C1, C2, C3, C4 to pin 5, pin 4, pin 3, pin 2. A membrane keypad is sixteen switches with no power pin, so nothing on it can exceed the Arduino Nano’s own 5 V levels and nothing needs shifting. The sketch below uses the Keypad (Keypad.h) library. It scans the rows and columns and prints each key you press.
- 5 V logic
- Library: Keypad.h
- 8 wires
4x4 keypad to Arduino Nano wiring table
Every wire in the circuit above, with the part’s pin names and the board’s own labels. The wire colors are the ones the circuit uses; on a real bench any colors work.
| 4x4 keypad pin | Arduino Nano pin | Wire color | Why |
|---|---|---|---|
| R1, R2, R3, R4 | pin 9, pin 8, pin 7, pin 6 | amber | The rows: the library drives one low at a time. |
| C1, C2, C3, C4 | pin 5, pin 4, pin 3, pin 2 | green | The columns: inputs with pull-ups, read for each row. |
Power and logic levels for 4x4 keypad and Arduino Nano
Logic level
The Arduino Nano’s pins are 5 V logic. A 5 V part can drive them directly; a part whose signal pins are limited to 3.3 V needs a level shifter.
This pair
A membrane keypad has no power pin: it is sixteen switches at the crossings of four row wires and four column wires. Eight pins of the Arduino Nano scan it, using the chip’s internal pull-ups, so no resistors are needed.
Pins to leave alone
A6 and A7 are analog only: pinMode(A6, OUTPUT) does nothing and digitalRead(A7) is not there to call. D0 and D1 are the USB serial port.
The working code for the Arduino Nano
Library: Keypad (Keypad.h). This is the sketch the circuit above runs.
#include <Keypad.h>
const byte ROWS = 4;
const byte COLS = 4;
char keys[ROWS][COLS] = {
{'1', '2', '3', 'A'},
{'4', '5', '6', 'B'},
{'7', '8', '9', 'C'},
{'*', '0', '#', 'D'},
};
byte rowPins[ROWS] = {9, 8, 7, 6}; // R1 to R4
byte colPins[COLS] = {5, 4, 3, 2}; // C1 to C4
Keypad keypad = Keypad(makeKeymap(keys), rowPins, colPins, ROWS, COLS);
void setup() {
Serial.begin(9600);
Serial.println("Press a key");
}
void loop() {
char key = keypad.getKey(); // 0 when nothing new was pressed
if (key) {
Serial.print("Key: ");
Serial.println(key);
}
}
What you should see
Open the serial monitor at 9600 baud. The sketch prints Press a key and then a Key line with the character of each key you press. The library debounces the keys itself.
If the wrong characters come out, the rows and columns are swapped: R1 to R4 must go to the row pins in the sketch, C1 to C4 to the column pins.
The serial monitor prints this, recorded from the circuit above with the 5 key pressed after 300 ms:
Press a key
Key: 5Common mistakes wiring a 4x4 keypad to an Arduino Nano
Rows and columns swapped
Swap the two arrays and every key prints its mirror across the diagonal, so 2 prints 4. If the wrong keys come out in a pattern, swap rowPins and colPins.
Pins listed in the wrong order
The connector order is R1 to R4 then C1 to C4 on most keypads, left to right with the keys facing you. List the pins in exactly that order or keys move around.
Running out of pins
A 4x4 keypad takes eight pins, which on the Arduino Nano leaves little room. An I2C port expander such as the PCF8574 scans it over two wires instead.
Build your own 4x4 keypad project
Open this circuit in the editor, change the wiring or the code, and keep your version in a free account.