Wiring guide

How to wire a BMP280 to an ESP32

To wire a BMP280 to an ESP32, connect VIN to 3V3, GND to GND, SCL to GPIO 22 (D22) and SDA to GPIO 21 (D21). The ESP32 and the BMP280 are both 3.3 V parts, so this is the simplest wiring there is: no regulator and no level shifter. The sketch below uses the Adafruit BMP280 (Adafruit_BMP280.h) library. It prints the temperature, the pressure and an altitude estimate.

  • 3.3 V logic
  • Library: Adafruit_BMP280.h
  • 4 wires
ESP32 · BMP280live0.000 s 0.00x
Click to open it in the editor
The circuit itself, running on the simulator with the sketch below. Press what can be pressed; click anything else to open it in the editor.
Pin to pin

BMP280 to ESP32 wiring table

Every wire in the circuit above, with the part’s pin names and the board’s own labels. The wire colors are the ones the circuit uses; on a real bench any colors work.

BMP280 pinESP32 pinWire colorWhy
VIN3V3redThe BMP280 chip is a 3.3 V part; many breakouts have no regulator.
GNDGNDblueCommon ground.
SCLGPIO 22 (D22)cyanI2C clock.
SDAGPIO 21 (D21)violetI2C data.
Voltage

Power and logic levels for BMP280 and ESP32

Logic level

The ESP32’s GPIO pins are 3.3 V logic and are not 5 V tolerant. Nothing wired to a pin may go above 3.3 V.

Supply

The BMP280 takes 3.3 V from 3V3. That pin is the ESP32’s own regulated 3.3 V output.

This pair

On an ESP32 DevKit, Wire.begin() with no arguments puts SDA on GPIO 21 and SCL on GPIO 22, labeled D21 and D22. The ESP32 and the BMP280 are both 3.3 V parts, so this is the simplest wiring there is: no regulator and no level shifter.

Pins to leave alone

GPIO 34, 35, 36 (VP) and 39 (VN) are input only: they cannot drive a pin or take an internal pull-up. GPIO 0, 2, 5, 12 and 15 are strapping pins, read at power-on, and GPIO 6 to 11 are the flash chip.

The sketch

The working code for the ESP32

Library: Adafruit BMP280 (Adafruit_BMP280.h). This is the sketch the circuit above runs.

BMP280 on ESP32 I2C
#include <Wire.h>
#include <Adafruit_BMP280.h>

Adafruit_BMP280 bmp;   // on I2C: SDA GPIO 21 (D21), SCL GPIO 22 (D22)

void setup() {
  Serial.begin(115200);
  if (!bmp.begin(0x76)) {
    Serial.println("No BMP280 at 0x76");
    for (;;) {}
  }
  Serial.println("BMP280 found");
}

void loop() {
  Serial.print("Temperature: ");
  Serial.print(bmp.readTemperature(), 1);
  Serial.print(" C  Pressure: ");
  Serial.print(bmp.readPressure() / 100.0F, 1);
  Serial.print(" hPa  Altitude: ");
  Serial.print(bmp.readAltitude(1013.25), 0);
  Serial.println(" m");
  delay(1000);
}
Output

What you should see

Open the serial monitor at 115200 baud. The sketch prints BMP280 found and then a line with the temperature in degrees C, the pressure in hectopascals and the altitude. The sensor starts at 22 degrees C and about 1013 hPa.

If it prints that no sensor was found, the address is the first thing to check: this circuit answers at 0x76, and some breakouts use 0x77.

The serial monitor prints this, recorded from the circuit above left at its defaults:

BMP280 found
Temperature: 22.0 C  Pressure: 1013.3 hPa  Altitude: 0 m
Pitfalls

Common mistakes wiring a BMP280 to an ESP32

The wrong address

Adafruit’s own board answers at 0x77, the cheap purple ones at 0x76, and bmp.begin() with no argument tries 0x77. If it fails, try the other address before suspecting the wiring.

Powering it from VIN (5 V from USB)

A breakout without a regulator is a bare 3.3 V chip: 5 V on VIN can kill it. Use 3V3, which on this board is also the right level for I2C.

Confusing it with a BME280

The BME280 looks the same and adds humidity. A BMP280 reports a chip ID of 0x58, a BME280 0x60, and each library refuses the other. If begin() fails at both addresses, check which chip you have.

Build your own BMP280 project

Open this circuit in the editor, change the wiring or the code, and keep your version in a free account.