Wiring guide

How to wire an RC522 RFID reader to a Raspberry Pi Pico

To wire an RC522 RFID reader to a Raspberry Pi Pico, connect 3.3V to 3V3(OUT), GND to GND, SDA to GP17 (physical pin 22), SCK to GP18 (physical pin 24), MOSI to GP19 (physical pin 25), MISO to GP16 (physical pin 21) and RST to GP20 (physical pin 26). The Raspberry Pi Pico and the MFRC522 are both 3.3 V, so the SPI lines connect directly. The sketch below uses the MFRC522 (MFRC522.h) library. It reads the card that is held to the reader and prints its UID.

  • 3.3 V logic
  • Library: MFRC522.h
  • 7 wires
Raspberry Pi Pico · RC522 RFID readerlive0.000 s 0.00x
Click to open it in the editor
The circuit itself, running on the simulator with the sketch below. Press what can be pressed; click anything else to open it in the editor.
Pin to pin

RC522 RFID reader to Raspberry Pi Pico wiring table

Every wire in the circuit above, with the part’s pin names and the board’s own labels. The wire colors are the ones the circuit uses; on a real bench any colors work.

RC522 RFID reader pinRaspberry Pi Pico pinWire colorWhy
3.3V3V3(OUT)redThe MFRC522 is a 3.3 V chip. Never 5 V on this pin.
GNDGNDblueCommon ground.
SDA (SS)GP17 (physical pin 22)amberChip select. Labeled SDA on the module, but this is SPI, not I2C.
SCKGP18 (physical pin 24)cyanRaspberry Pi Pico’s SPI clock.
MOSIGP19 (physical pin 25)violetData from the board to the reader.
MISOGP16 (physical pin 21)greenData from the reader to the board.
RSTGP20 (physical pin 26)grayReset, held high while the reader runs.
IRQnot connectedn/aThe library polls instead.
Voltage

Power and logic levels for RC522 RFID reader and Raspberry Pi Pico

Logic level

The Raspberry Pi Pico’s GPIO pins are 3.3 V logic and are not 5 V tolerant. Nothing wired to a pin may go above 3.3 V.

Supply

The RC522 RFID reader takes 3.3 V from 3V3(OUT). That pin is the Raspberry Pi Pico’s own regulated 3.3 V output.

This pair

The Raspberry Pi Pico and the MFRC522 are both 3.3 V, so the SPI lines connect directly: the cleanest RC522 wiring there is.

Pins to leave alone

The numbers in the code are GP numbers, not the physical pin numbers printed beside the header: GP15 is pin 20. GP23 to GP25 are used on the board itself, and GP25 is the LED.

The sketch

The working code for the Raspberry Pi Pico

Library: MFRC522 (MFRC522.h). This is the sketch the circuit above runs.

RC522 RFID on Raspberry Pi Pico
#include <SPI.h>
#include <MFRC522.h>

const int SS_PIN = 17;    // SDA on the module, GP17 (physical pin 22)
const int RST_PIN = 20;   // GP20 (physical pin 26)

MFRC522 rfid(SS_PIN, RST_PIN);

void setup() {
  Serial.begin(115200);
  SPI.begin();          // SCK 18, MISO 16, MOSI 19
  rfid.PCD_Init();
  Serial.println("Hold a card to the reader");
}

void loop() {
  if (!rfid.PICC_IsNewCardPresent() || !rfid.PICC_ReadCardSerial()) {
    delay(50);
    return;
  }
  Serial.print("Card UID:");
  for (byte i = 0; i < rfid.uid.size; i++) {
    Serial.print(rfid.uid.uidByte[i] < 0x10 ? " 0" : " ");
    Serial.print(rfid.uid.uidByte[i], HEX);
  }
  Serial.println();
  rfid.PICC_HaltA();    // done with this card until it is lifted
}
Output

What you should see

Open the serial monitor at 115200 baud. The sketch prints Hold a card to the reader and, when you present the card in the circuit, a Card UID line with its four bytes in hexadecimal.

The pin labeled SDA on the module is the SPI chip select, not an I2C line. IRQ is left unconnected because the library polls.

The serial monitor prints this, recorded from the circuit above with a card presented after 400 ms:

Hold a card to the reader
Card UID: C3 5A 1E 94
Pitfalls

Common mistakes wiring an RC522 RFID reader to a Raspberry Pi Pico

Powering it from 5V

The 3.3V pin means it: 5 V there damages the MFRC522. If the module gets warm or reports a version of 0x00 or 0xFF, check this first.

Mixing up SPI0 and SPI1

SPI.begin() uses SPI0 on GP16 to GP19. Pico tutorials sometimes put the reader on SPI1 (GP10 to GP13), which needs SPI1.begin() and a different object.

Expecting to read bank cards

The RC522 reads 13.56 MHz MIFARE tags and cards. Contactless bank cards answer, but only with a random ID each time, and 125 kHz key fobs not at all.

Build your own RC522 RFID reader project

Open this circuit in the editor, change the wiring or the code, and keep your version in a free account.