Wiring guide

How to wire an IR receiver to a Raspberry Pi Pico

To wire an IR receiver to a Raspberry Pi Pico, connect VCC to 3V3(OUT), GND to GND and OUT to GP15 (physical pin 20). Power the receiver from 3.3 V so its output swings to 3.3 V, the board’s own level; from 5 V its output would idle at 5 V on a 3.3 V pin. The sketch below uses the IRremote (IRremote.hpp) library. It decodes the buttons of an NEC remote and prints each command code.

  • 3.3 V logic
  • Library: IRremote.hpp
  • 3 wires, 1 helper parts
Raspberry Pi Pico · IR receiverlive0.000 s 0.00x
Click to open it in the editor
The circuit itself, running on the simulator with the sketch below. Press what can be pressed; click anything else to open it in the editor.
Pin to pin

IR receiver to Raspberry Pi Pico wiring table

Every wire in the circuit above, with the part’s pin names and the board’s own labels. The wire colors are the ones the circuit uses; on a real bench any colors work.

IR receiver pinRaspberry Pi Pico pinWire colorWhy
VCC3V3(OUT)redThe VS1838B-style receiver runs from 2.7 to 5.5 V.
GNDGNDblueGround.
OUTGP15 (physical pin 20)amberLow while a 38 kHz burst arrives, high otherwise: the demodulated code.
IR (light)The remoten/aIn the editor the infrared light path is drawn as a gray wire from the remote.

Helper parts

The extra parts in the circuit above, and where their wires go:

FromToWire color
RM1 pin IRIRgray
Voltage

Power and logic levels for IR receiver and Raspberry Pi Pico

Logic level

The Raspberry Pi Pico’s GPIO pins are 3.3 V logic and are not 5 V tolerant. Nothing wired to a pin may go above 3.3 V.

Supply

The IR receiver takes 3.3 V from 3V3(OUT). That pin is the Raspberry Pi Pico’s own regulated 3.3 V output.

This pair

Power the receiver from 3V3 on the Raspberry Pi Pico: its output then swings to 3.3 V, the board’s own level. Fed from 5 V, its output would idle at 5 V on a 3.3 V pin.

Pins to leave alone

The numbers in the code are GP numbers, not the physical pin numbers printed beside the header: GP15 is pin 20. GP23 to GP25 are used on the board itself, and GP25 is the LED.

The sketch

The working code for the Raspberry Pi Pico

Library: IRremote (IRremote.hpp). This is the sketch the circuit above runs.

IR receiver on Raspberry Pi Pico GP15 (physical pin 20)
#include <IRremote.hpp>

const int IR_PIN = 15;   // OUT, GP15 (physical pin 20)

void setup() {
  Serial.begin(115200);
  IrReceiver.begin(IR_PIN);
  Serial.println("Point the remote and press a button");
}

void loop() {
  if (IrReceiver.decode()) {
    if (!(IrReceiver.decodedIRData.flags & IRDATA_FLAGS_IS_REPEAT)) {
      Serial.print("Command: 0x");
      Serial.println(IrReceiver.decodedIRData.command, HEX);
    }
    IrReceiver.resume();   // ready for the next one
  }
}
Output

What you should see

Open the serial monitor at 115200 baud. The sketch prints Point the remote and press a button, and then a Command line in hexadecimal for each button press on the remote in the circuit.

A receiver that never prints anything is usually on the wrong pin, or the remote uses a protocol other than NEC.

The serial monitor prints this, recorded from the circuit above with one remote button pressed after 300 ms:

Point the remote and press a button
Command: 0x47
Pitfalls

Common mistakes wiring an IR receiver to a Raspberry Pi Pico

Old IRremote code

Sketches written for IRremote 2.x use IRrecv irrecv(pin), irrecv.enableIRIn() and results.value. Version 3 and later use IrReceiver and decodedIRData, as here. Mixing the two is the most common reason an IR sketch will not compile.

Forgetting resume()

After decode() returns true, the library holds the code until resume() is called. Leave it out and the first button press is the only one you ever see.

Counting physical pins instead of GP numbers

The sketch says 15, which means GP15, and that is physical pin 20 on the header. Counting 15 pins down the side lands on a different GPIO, and the part never answers.

Build your own IR receiver project

Open this circuit in the editor, change the wiring or the code, and keep your version in a free account.