How to wire an RC522 RFID reader to an Arduino Uno
To wire an RC522 RFID reader to an Arduino Uno, connect 3.3V to 3.3V, GND to GND, SDA to pin 10, SCK to pin 13, MOSI to pin 11, MISO to pin 12 and RST to pin 9. The module is powered from 3.3 V but the SPI lines come from 5 V pins; many modules survive that, but the chip is rated for 3.3 V logic, so use a level shifter on SCK, MOSI, SS and RST on real hardware. The sketch below uses the MFRC522 (MFRC522.h) library. It reads the card that is held to the reader and prints its UID.
- 5 V logic
- Library: MFRC522.h
- 7 wires
RC522 RFID reader to Arduino Uno wiring table
Every wire in the circuit above, with the part’s pin names and the board’s own labels. The wire colors are the ones the circuit uses; on a real bench any colors work.
| RC522 RFID reader pin | Arduino Uno pin | Wire color | Why |
|---|---|---|---|
| 3.3V | 3.3V | red | The MFRC522 is a 3.3 V chip. Never 5 V on this pin. |
| GND | GND | blue | Common ground. |
| SDA (SS) | pin 10 | amber | Chip select. Labeled SDA on the module, but this is SPI, not I2C. |
| SCK | pin 13 | cyan | Arduino Uno’s SPI clock. |
| MOSI | pin 11 | violet | Data from the board to the reader. |
| MISO | pin 12 | green | Data from the reader to the board. |
| RST | pin 9 | gray | Reset, held high while the reader runs. |
| IRQ | not connected | n/a | The library polls instead. |
Power and logic levels for RC522 RFID reader and Arduino Uno
Logic level
The Arduino Uno’s pins are 5 V logic. A 5 V part can drive them directly; a part whose signal pins are limited to 3.3 V needs a level shifter.
This pair
The module is powered from the Arduino Uno’s 3.3V pin, but the SPI lines come from 5 V pins. Many RC522 modules survive that, and countless Uno tutorials wire it so, but the chip is rated for 3.3 V logic; a level shifter on SCK, MOSI, SS and RST is the safe way on real hardware.
Pins to leave alone
Pins 0 and 1 are the USB serial port on a real Uno, so anything wired there fights the upload and the serial monitor. Pin 13 carries the onboard LED.
The working code for the Arduino Uno
Library: MFRC522 (MFRC522.h). This is the sketch the circuit above runs.
#include <SPI.h>
#include <MFRC522.h>
const int SS_PIN = 10; // SDA on the module, pin 10
const int RST_PIN = 9; // pin 9
MFRC522 rfid(SS_PIN, RST_PIN);
void setup() {
Serial.begin(9600);
SPI.begin(); // SCK 13, MISO 12, MOSI 11
rfid.PCD_Init();
Serial.println("Hold a card to the reader");
}
void loop() {
if (!rfid.PICC_IsNewCardPresent() || !rfid.PICC_ReadCardSerial()) {
delay(50);
return;
}
Serial.print("Card UID:");
for (byte i = 0; i < rfid.uid.size; i++) {
Serial.print(rfid.uid.uidByte[i] < 0x10 ? " 0" : " ");
Serial.print(rfid.uid.uidByte[i], HEX);
}
Serial.println();
rfid.PICC_HaltA(); // done with this card until it is lifted
}
What you should see
Open the serial monitor at 9600 baud. The sketch prints Hold a card to the reader and, when you present the card in the circuit, a Card UID line with its four bytes in hexadecimal.
The pin labeled SDA on the module is the SPI chip select, not an I2C line. IRQ is left unconnected because the library polls.
The serial monitor prints this, recorded from the circuit above with a card presented after 400 ms:
Hold a card to the reader
Card UID: C3 5A 1E 94Common mistakes wiring an RC522 RFID reader to an Arduino Uno
Powering it from 5V
The 3.3V pin means it: 5 V there damages the MFRC522. If the module gets warm or reports a version of 0x00 or 0xFF, check this first.
Treating SDA as I2C
The pin marked SDA is the SPI chip select. Wired to the Arduino Uno’s I2C data pin, the reader is never selected. It goes to SS_PIN, pin 10 here.
Expecting to read bank cards
The RC522 reads 13.56 MHz MIFARE tags and cards. Contactless bank cards answer, but only with a random ID each time, and 125 kHz key fobs not at all.
Build your own RC522 RFID reader project
Open this circuit in the editor, change the wiring or the code, and keep your version in a free account.