Wiring guide

How to wire a PIR motion sensor to a Raspberry Pi Pico

To wire a PIR motion sensor to a Raspberry Pi Pico, connect VCC to VBUS (5 V from USB), OUT to GP15 (physical pin 20) and GND to GND. The module needs 5 V for power but its output is 3.3 V, so OUT connects straight to the Raspberry Pi Pico with no divider. The sketch below uses no library beyond what the board includes. It prints Motion detected whenever the sensor’s output goes high.

  • 3.3 V logic
  • Library: none
  • 3 wires
Raspberry Pi Pico · PIR motion sensorlive0.000 s 0.00x
Click to open it in the editor
The circuit itself, running on the simulator with the sketch below. Press what can be pressed; click anything else to open it in the editor.
Pin to pin

PIR motion sensor to Raspberry Pi Pico wiring table

Every wire in the circuit above, with the part’s pin names and the board’s own labels. The wire colors are the ones the circuit uses; on a real bench any colors work.

PIR motion sensor pinRaspberry Pi Pico pinWire colorWhy
VCCVBUS (5 V from USB)redThe HC-SR501 takes 4.5 to 20 V and regulates it down to 3.3 V on board.
OUTGP15 (physical pin 20)amberA 3.3 V high while it sees motion, then low.
GNDGNDblueCommon ground.
Voltage

Power and logic levels for PIR motion sensor and Raspberry Pi Pico

Logic level

The Raspberry Pi Pico’s GPIO pins are 3.3 V logic and are not 5 V tolerant. Nothing wired to a pin may go above 3.3 V.

Supply

The PIR motion sensor takes 5 V from VBUS (5 V from USB). That is the Raspberry Pi Pico’s 5 V rail, so the part shares the current the board can supply.

This pair

The module needs VBUS (5 V from USB) for power, but its output is 3.3 V, so OUT connects straight to the Raspberry Pi Pico with no divider. That makes the PIR one of the few 5 V modules that is a perfect match for a 3.3 V board.

Pins to leave alone

The numbers in the code are GP numbers, not the physical pin numbers printed beside the header: GP15 is pin 20. GP23 to GP25 are used on the board itself, and GP25 is the LED.

The sketch

The working code for the Raspberry Pi Pico

Library: none, the sketch reads OUT with digitalRead(). This is the sketch the circuit above runs.

PIR sensor on Raspberry Pi Pico GP15 (physical pin 20)
const int PIR_PIN = 15;   // OUT, GP15 (physical pin 20)
int lastState = LOW;

void setup() {
  Serial.begin(115200);
  pinMode(PIR_PIN, INPUT);
  Serial.println("Watching for motion");
}

void loop() {
  int state = digitalRead(PIR_PIN);
  if (state != lastState) {
    lastState = state;
    Serial.println(state == HIGH ? "Motion detected" : "Motion ended");
  }
  delay(50);
}
Output

What you should see

Open the serial monitor at 115200 baud. The sketch prints Watching for motion once; each time the sensor sees movement, a Motion detected line follows, and Motion ended when it settles. In the editor, click the sensor to trigger it.

Real PIR modules need about a minute to settle after power-up and then hold their output high for a few seconds per trigger.

The serial monitor prints this, recorded from the circuit above with motion triggered after 300 ms:

Watching for motion
Motion detected
Pitfalls

Common mistakes wiring a PIR motion sensor to a Raspberry Pi Pico

Not waiting for it to settle

A real HC-SR501 needs up to a minute after power-up to learn the room, and gives false triggers until then. Ignore it for the first 30 to 60 seconds.

The hold time knob

The orange trimmer next to the sensitivity one sets how long OUT stays high, from about 3 seconds to several minutes. A sensor that seems stuck on is usually turned all the way up. The simulated part has a hold property for the same thing.

Powering it from 3V3

Its regulator wants 4.5 V or more; at 3.3 V it triggers at random or not at all. Power from VBUS (5 V from USB); the output is already 3.3 V.

Build your own PIR motion sensor project

Open this circuit in the editor, change the wiring or the code, and keep your version in a free account.