Wiring guide

How to wire an MPU6050 to a Raspberry Pi Pico

To wire an MPU6050 to a Raspberry Pi Pico, connect VCC to 3V3(OUT), GND to GND, SCL to GP5 (physical pin 7) and SDA to GP4 (physical pin 6). Power the GY-521 from 3.3 V so its pull-ups hold SDA and SCL at 3.3 V, the board’s own level. The sketch below uses no library beyond what the board includes. It wakes the sensor and prints the raw acceleration on three axes every half second.

  • 3.3 V logic
  • Library: Wire.h
  • 4 wires
Raspberry Pi Pico · MPU6050live0.000 s 0.00x
Click to open it in the editor
The circuit itself, running on the simulator with the sketch below. Press what can be pressed; click anything else to open it in the editor.
Pin to pin

MPU6050 to Raspberry Pi Pico wiring table

Every wire in the circuit above, with the part’s pin names and the board’s own labels. The wire colors are the ones the circuit uses; on a real bench any colors work.

MPU6050 pinRaspberry Pi Pico pinWire colorWhy
VCC3V3(OUT)redThe GY-521 board has a 3.3 V regulator, so it takes 3.3 or 5 V.
GNDGNDblueCommon ground.
SCLGP5 (physical pin 7)cyanI2C clock.
SDAGP4 (physical pin 6)violetI2C data.
AD0not connectedn/aLow (the board’s own pull-down): address 0x68. Tie it high for 0x69.
Voltage

Power and logic levels for MPU6050 and Raspberry Pi Pico

Logic level

The Raspberry Pi Pico’s GPIO pins are 3.3 V logic and are not 5 V tolerant. Nothing wired to a pin may go above 3.3 V.

Supply

The MPU6050 takes 3.3 V from 3V3(OUT). That pin is the Raspberry Pi Pico’s own regulated 3.3 V output.

This pair

On the Pico, Wire.begin() puts SDA on GP4 and SCL on GP5, physical pins 6 and 7. Powered from 3V3, the GY-521’s pull-ups hold SDA and SCL at 3.3 V, the Raspberry Pi Pico’s own level. Its regulator still works from 3.3 V, with a little less headroom.

Pins to leave alone

The numbers in the code are GP numbers, not the physical pin numbers printed beside the header: GP15 is pin 20. GP23 to GP25 are used on the board itself, and GP25 is the LED.

The sketch

The working code for the Raspberry Pi Pico

Library: none, only Wire.h: the sketch reads the registers itself. This is the sketch the circuit above runs.

MPU6050 on Raspberry Pi Pico I2C
#include <Wire.h>

const int MPU = 0x68;   // AD0 low

int16_t read16() {
  int16_t high = Wire.read();
  return (high << 8) | Wire.read();
}

void setup() {
  Serial.begin(115200);
  Wire.begin();                 // SDA GP4 (physical pin 6), SCL GP5 (physical pin 7)
  Wire.beginTransmission(MPU);
  Wire.write(0x6B);             // PWR_MGMT_1
  Wire.write(0);                // wake up: it starts asleep
  Wire.endTransmission();
  Serial.println("MPU6050 awake");
}

void loop() {
  Wire.beginTransmission(MPU);
  Wire.write(0x3B);             // ACCEL_XOUT_H, then Y, Z, temperature, gyro
  Wire.endTransmission(false);
  Wire.requestFrom(MPU, 6);
  int16_t ax = read16();
  int16_t ay = read16();
  int16_t az = read16();
  // At the default range, 16384 counts is 1 g.
  Serial.print("Accel x: ");
  Serial.print(ax);
  Serial.print("  y: ");
  Serial.print(ay);
  Serial.print("  z: ");
  Serial.println(az);
  delay(250);
}
Output

What you should see

Open the serial monitor at 115200 baud. The sketch prints MPU6050 awake and then the raw acceleration on x, y and z. Lying flat, x and y read near zero and z reads about 16384, which is 1 g at the default range.

Tilt the sensor in the editor and the numbers follow. The AD0 pin is left open, which puts the sensor at address 0x68.

The serial monitor prints this, recorded from the circuit above lying flat:

MPU6050 awake
Accel x: 0  y: 0  z: 16384
Pitfalls

Common mistakes wiring an MPU6050 to a Raspberry Pi Pico

Not waking it up

Out of reset the chip is asleep and returns zeros on every axis. Write 0 to register 0x6B first. It is the single most common MPU6050 fault.

Reading the axes in separate transactions

Read X, then start a new transaction for Y, and the chip may have taken a new sample in between, so the axes disagree. Read all six bytes from 0x3B in one requestFrom().

Expecting an angle from the gyro

The gyroscope measures how fast the board turns, in degrees per second, not which way it points. For tilt, use the arctangent of two acceleration axes; for a steady angle while moving, combine both with a complementary filter.

Build your own MPU6050 project

Open this circuit in the editor, change the wiring or the code, and keep your version in a free account.