Arduino library · Sensors

arduino-sht: an example that runs

Yes. You can use the arduino-sht library online in Mokxi with nothing to install, and the sketch runs in your browser against the simulated part (Temperature and humidity, SHT31). The example below, "Autodetect a Sensirion SHT and read it", runs on the Arduino Uno R3.

Built in on Mokxi: #include <SHTSensor.h> and it builds, with nothing to install. Free, and no account needed.

What arduino-sht does

SHTSensor: init() that autodetects the SHT4x, SHT3x, SHT85, SHT2x and SHTC1/SHTC3, readSample(), getTemperature(), getHumidity() and setAccuracy(). That is what arduino-sht, by Sensirion, covers. The sketch below uses it on the Arduino Uno: “Autodetect a Sensirion SHT and read it”.

Sensirion's arduino-sht library, one class for the SHT2x, SHT3x, SHT85, SHTC1, SHTC3, SHTW1/2 and SHT4x humidity sensors, with autodetection.

init() with AUTO_DETECT tries, in upstream's order, an SHT4x at 0x44, an SHT2x at 0x40, an SHT3x at 0x44 and 0x45 and an SHTC1/SHTC3 at 0x70, and keeps the first that hands back a measurement with good CRCs. Each sensor is a single-shot command, the datasheet's wait and six bytes (the SHT2x is two commands of three).

The calls follow release 2.0.0 of the library, so a sketch written here builds on a real board too. The example is the one Mokxi's own tests build and run, so what is printed here is what runs.

Library Manager namearduino-sht
AuthorSensirion
Include#include <SHTSensor.h>
Boardsevery board Mokxi compiles for but ATtiny85
In the simulatorSimulated: it runs against the part the way it does on the bench.
Parts it drivesTemperature and humidity, SHT31, Temperature and humidity, SHT40

Install it

It builds on every board Mokxi compiles for but ATtiny85.

In Mokxi it is built in: #include <SHTSensor.h> and the sketch compiles, with no download, no zip and no Library Manager.

On a real board, install "arduino-sht" by Sensirion from the Arduino IDE’s Library Manager (Sketch, Include Library, Manage Libraries), or add arduino-sht to lib_deps in PlatformIO. Mokxi follows the calls of release 2.0.0, so a sketch written here builds there too.

What to know in the simulator: Mokxi has the SHT31 and SHT4x parts; an SHT2x or SHTC3 finds nothing on the bus. SHT3xAnalogSensor builds, but there is no analog SHT3x part.

The calls you will use

In the order a sketch meets them.

SHTSensor sht

Makes sht, the SHTSensor object the calls below are made on.

sht.init()

Starts it up and returns true if it started, false if it did not. Call it once in setup().

sht.getSensorType()

Returns the sensor type as a SHTSensorType.

sht.setAccuracy(SHTSensor::SHT_ACCURACY_MEDIUM)

Sets the accuracy to the value you pass in. Arguments: new accuracy.

sht.readSample()

Returns the sample as true or false.

sht.getHumidity()

Returns the humidity as a decimal number.

sht.getTemperature()

Returns the temperature as a decimal number.

Example: Autodetect a Sensirion SHT and read it

On the Arduino Uno R3. It runs in the browser exactly as printed.

sketch.ino · Arduino Uno R3
#include <Arduino.h>
#include <Wire.h>
#include "SHTSensor.h"

SHTSensor sht;
// To use a specific sensor instead of probing the bus:
// SHTSensor sht(SHTSensor::SHT3X);

void setup() {
  Wire.begin();
  Serial.begin(9600);
  delay(100);

  if (sht.init()) {
    Serial.print("init(): success\n");
    switch (sht.getSensorType()) {
      case SHTSensor::SHT3X: Serial.println("Sensor detected: SHT3x/SHT85 (I2C address 0x44)"); break;
      case SHTSensor::SHT4X: Serial.println("Sensor detected: SHT4x"); break;
      default: Serial.println("Sensor detected: other"); break;
    }
  } else {
    Serial.print("init(): failed\n");
  }
  sht.setAccuracy(SHTSensor::SHT_ACCURACY_MEDIUM); // only supported by SHT3x
}

void loop() {
  if (sht.readSample()) {
    Serial.print("SHT:\n");
    Serial.print("  RH: ");
    Serial.print(sht.getHumidity(), 2);
    Serial.print("\n");
    Serial.print("  T:  ");
    Serial.print(sht.getTemperature(), 2);
    Serial.print("\n");
  } else {
    Serial.print("Error in readSample()\n");
  }
  delay(1000);
}

Wiring

  • Arduino Uno R3 A4 to Temperature and humidity, SHT31 SDA
  • Arduino Uno R3 A5 to Temperature and humidity, SHT31 SCL
  • Arduino Uno R3 5V to Temperature and humidity, SHT31 VIN
  • Arduino Uno R3 GND to Temperature and humidity, SHT31 GND

Open it in the editor, wired and ready to run

Try arduino-sht without installing anything

Open the example, change the sketch, and keep your version in a free account.