A pressure sensor simulator: read a BMP388 barometer on an Arduino Uno
Mokxi is a free online pressure sensor simulator that runs in your browser, with nothing to install and no account needed. A BMP388 barometric pressure sensor wired to an Arduino Uno: VIN to 5V, GND to GND, SDA to A4 and SCL to A5. The sketch reads it with Adafruit_BMP3XX.h and the serial monitor prints the pressure.
- 526parts on the bench
- 46boards running now
- 1.00xreal time, on every board
What you can do here
In the circuit above, or in the editor it opens.
- Watch the serial monitor print the pressure every second
- Drag the pressure slider and see the altitude change
- Set the temperature, which starts at 22
- Read the wiring: VIN to 5V, GND to GND, SDA to A4, SCL to A5
- Set SEA_LEVEL_HPA to today's sea-level pressure for a true altitude
- Open the sketch and follow the things to try in the comments
What the running circuit shows
Pressure, temperature and altitude, printed once a second.
At the default settings the sketch finds the chip and prints each second: “BMP388 found at 0x77” then “pressure 1013.25 hPa, temperature 22.00 C, altitude -0.0 m”. The pressure slider starts at 1013.25 and the temperature starts at 22.
Drag the pressure slider down to 950 and the next measurement changes: “pressure 950.00 hPa, temperature 22.00 C, altitude 540.4 m”. Less pressure reads as more altitude, which is exactly how a barometer works as an altimeter.
The sketch comments explain the rule of thumb: about 12 Pa, or 0.12 hPa, less is a meter higher. You can watch that play out on the sliders.
How the barometric pressure sensor is modeled
Two sliders stand in for the weather.
The Bosch BMP388 reads air pressure and temperature over I2C at address 0x77 or 0x76. Its readings are raw 24-bit counts, and the library turns them into pascals and degrees using 21 trimming bytes Bosch writes into every chip at the factory.
The simulator models two properties: pressure in hPa, from 300 to 1250, and temperature in degrees C, from -40 to 85, the datasheet's operating range. The two sliders change them while the circuit runs, and the next measurement reports them.
Three steps from a blank tab to a running circuit.
Open the editor
It runs in your browser tab. Nothing to install, and you need no account to start.
Your first projectWire it and write the code
Drag parts onto a breadboard, run each wire from pin to pin, and write the sketch beside it.
WiringPress Run
Your sketch compiles in the tab and runs on a model of the chip, with the Serial Monitor beside it.
Run and serial
Open a project and press Run.
Every one runs in the editor exactly as it is drawn, ready to change.
What makers say about Mokxi.
“The AI checker helps check and correct my circuits, and it has way more components than Tinkercad. As a student I really appreciate the tool.”
“I’d been looking for a real online electronic simulator that was intuitive and complete when I found Mokxi. I was able to quickly import a Fritzing file and my Arduino sketch and start testing. Mokxi has all of the makings for the best online Arduino simulator I have been able to find!”
“I’m using Mokxi to develop and simulate an STM32-based four-wheel-drive robot car before building the actual hardware. It allows me to experiment with DC motor control, PWM, RPM measurement using photointerrupters, and different acceleration, braking, and reversing strategies, helping me understand and refine the system before implementing it in real life.”
Questions, answered.
Is it free?
Yes. The circuit on this page, every part in it and the editor it opens in are on the free plan, with no card.
Do I need an account?
No. The circuit runs the moment the page does, and the editor opens without one. A free account is only for saving a project to the cloud and sharing it by link.
Can two BMP388 sensors share one I2C bus?
Yes. SDO is the address bit. Left alone the board pulls it up and the address is 0x77; to GND it is 0x76. The sketch would then call begin_I2C(0x76).
How do I get a true altitude instead of height above sea level?
Set SEA_LEVEL_HPA to today's sea-level pressure from a weather report. Or read the pressure once in setup() and use that, and the sketch shows height above the desk.
Is 5 V on VIN safe for this board?
Yes. The board has its own regulator and level shifters, so 5 V on VIN is fine even though the chip itself runs from 1.65 to 3.6 V.
Do I need an account at all?
No. The editor, the templates, the gallery, the compiler and Run all work without signing in. Your browser keeps your work as you go. An account saves your projects online, so they follow you to any computer. It also gives you a link to share.
Which boards are supported?
Forty-five, all on the free plan. Arduino: the Uno R3, Uno R4 Minima and Uno R4 WiFi, Nano, Nano ESP32, Nano RP2040 Connect, Mega 2560, Leonardo, Micro, the Pro Mini in its 5 V and 3.3 V builds, and the SparkFun Pro Micro. ESP32: the classic DevKit V1, the ESP32-S3, the ESP32-C3 and C6 DevKits, the Espressif DevKitC V4, the Freenove ESP32-WROVER, the Wemos LOLIN32 Lite, the Wemos D1 R32, the Cheap Yellow Display, the TTGO T-Display, the ESP32-C3 SuperMini and the Seeed XIAO ESP32-C3, C6 and S3. ESP8266: the NodeMCU, the Wemos D1 mini and the ESP-01S. Also the Raspberry Pi Pico and Pico W, the Seeed XIAO RP2040, the Waveshare RP2040-Zero, the Seeed XIAO SAMD21, the WCH CH32V003, the STM32F411 Black Pill, the STM32 Nucleo-F411RE and the STM32F103 Blue Pill, the BBC micro:bit V2, and the ATtiny85 and the ATmega328P in its 16 MHz and 8 MHz builds, which plug straight into the breadboard as bare chips. Your own code compiles in the browser for all of them. Then the Raspberry Pi 4, Pi 5 and Zero 2 W computers, which run your Python with gpiozero and RPi.GPIO, with nothing to compile. Each board page lists what it can and can’t do. For example, the WiFi boards have pretend WiFi, not a real radio, and the page says so.
Is my sketch really compiled in the browser?
Yes. A real compiler (clang, built for the web) runs in your browser. It downloads once, and your browser keeps a copy. After that, every build happens on your own computer. There is no build server and no waiting in line, so there are no build minutes to run out of.
Which browsers work?
Any up-to-date Chrome, Edge, Firefox or Safari, on a computer, a phone or a tablet. They all support WebAssembly, which Mokxi needs, and they have for years.
Does it work on a phone?
Yes. The editor works with touch, the buttons are big enough to tap, and the layout fits a small screen. The simulation runs on the phone itself.
Can I try Pro before I pay?
Yes. Every account can try Pro free for 7 days, once. It takes a card, nothing is charged for those days, and if you cancel before they end you pay nothing. It starts when you choose it.
Can I cancel anytime?
Yes, in one press from your account page. Your plan runs to the end of what you paid for.
Do you offer refunds?
Yes, once per account. Write to us within 14 days of a payment and we refund all of it. Lifetime Pro is refunded in full within 14 days of buying it.
Is there a student discount?
Yes. Students get Pro at half price with a school email.
Do students need accounts?
No. The simulator works signed out, so your class starts from one link with nothing to sign up for. An account only adds cloud saving and sharing, and a student can make one later, or never.
Does it work on a Chromebook?
Yes. Everything runs on the machine in front of the student, so a Chromebook works as well as a lab PC.
What does it cost for a class?
Nothing, if your students only need to open and run circuits: the whole simulator is on the free plan. The class tools (a roster, starter projects, auto-graded checks, the gradebook) come with Pro and Classroom. Classroom is $9.99 a student a year, from 5 students, so at least $49.95 for the year. Your own seat is free, and from 50 students each one costs less. Your students get Pro’s room while they are in your classes. Pay by card, invoice or purchase order. Pro on its own runs classes for up to 10 students in all. To try the class tools with real students first, start the free 30-day trial from your class page: one class of up to 20 students, no card.
Is student work private?
Yes. A student’s projects in a class are always private: they cannot be opened by link or put in the gallery. One exception, and only for reading: a teacher may open, and never write, a project owned by somebody in a class they teach, which is what a card on the class wall does. What we store about a student, who processes it, how a school has it deleted, and how we handle COPPA consent for students under 13 and FERPA as a school official are all on the student data privacy page at /privacy/students.
Is Mokxi AI free?
Every signed-in account gets questions: 5 a day on a free account, 700 for the 7 days on the Pro trial, 3,000 every month on Pro and the other paid plans, and 25 a day on Lifetime Pro.
Does Mokxi AI work with ESP32 and Raspberry Pi Pico sketches?
Yes. It knows which board the project is on and answers for that board, from an Uno to an ESP32, an ESP8266, a Pico or an STM32.
Can Mokxi AI change my code without asking?
No. It proposes a change as a card. Accept is yours, and only appears once the changed code compiles; Ctrl+Z undoes it.
What does Mokxi AI send with a question?
Your project text, the matching help articles and the last six messages of the chat, never your name or account. "What is sent" shows exactly what went.
Latest arrivals in Mokxi.
More simulators
Each one opens on a circuit that is already running.
Measure the air
Open the circuit, drag the pressure slider and watch the altitude climb. Nothing to install, and no account needed.





