Kit: a button that lights an LED
Read a pushbutton with the chip’s own pull-up resistor and light an LED only while it is held.
Open it in the simulatorFollows the lessons in the Elegoo Uno R3 Super Starter Kit tutorial, in its order, each one running in your browser.
0 of 24 done
24 lessons in 5 chapters, about 14 hours on a simulated Arduino Uno R3. Free, in your browser, every step checked by the simulator.
Read a pushbutton with the chip’s own pull-up resistor and light an LED only while it is held.
Open it in the simulatorA servo turns to an angle and holds it. Send it to 0, 90 and 180 degrees, then sweep it back one degree at a time.
Open it in the simulatorThe receiver turns flashes of infrared into pulses, and the IRremote library turns the pulses into a button’s code.
Open it in the simulatorFour digits share their segment pins and take turns, four milliseconds each, faster than your eye can follow.
Open it in the simulatorPut two lessons together: VOL+ and VOL- on the remote turn the stepper a quarter turn each way.
Open it in the simulatorEach lesson opens when the one before it is done, and each chapter ends in a project.
Print, blink, light an LED, mix colors and read a button.
Printing is how you find out what a board thinks. What Serial.begin does, what a baud rate really costs, and how to print a number without lying about it.
0 of 6 steps
Two wires from an Arduino Uno to the LED you already know, then press Run and let a program do the switching. Four steps, no code to write.
0 of 4 steps
Start with the parts in place. Draw every wire yourself, close the loop, press Run and light the LED.
0 of 5 steps
Three LEDs under one lens. Fade red, green and blue with analogWrite and watch the colors in between appear.
0 of 4 steps
Read a pushbutton with the chip’s own pull-up resistor and light an LED only while it is held.
0 of 4 steps
Two kinds of buzzer, a tilt switch and a servo.
A buzzer with its own oscillator: power it and it sounds. The sketch only decides when.
0 of 4 steps
A passive buzzer makes no sound on its own. tone() switches the pin at a note’s frequency and plays a tune.
0 of 4 steps
A little ball that closes a contact while it stands up. Read it, filter its bounce, and light an LED when it tips.
0 of 4 steps
A servo turns to an angle and holds it. Send it to 0, 90 and 180 degrees, then sweep it back one degree at a time.
0 of 4 steps
Distance, temperature, a joystick and a remote control.
The HC-SR04 times an echo. Turn the time into centimeters, then beep faster as something comes closer.
0 of 4 steps
A sensor with its own little chip, read over one wire. Print the temperature and the humidity every two seconds.
0 of 4 steps
A joystick is two knobs and a button. Read both axes with analogRead and draw the position on a bar of LEDs.
0 of 4 steps
The receiver turns flashes of infrared into pulses, and the IRremote library turns the pulses into a button’s code.
0 of 4 steps
An LCD, a shift register, the serial monitor and seven-segment digits.
Wire the character display with six signal lines and the LiquidCrystal library, then count the seconds on it.
0 of 4 steps
A resistor that changes with temperature, a voltage divider, and the beta equation: degrees on the LCD.
0 of 4 steps
The 74HC595 shift register takes a byte one bit at a time and shows all eight bits at once.
0 of 4 steps
The monitor is an input too. Read characters without blocking, act on them, and answer everything, including the things you do not understand.
0 of 6 steps
A resistor that changes with light, read on A0, shown as a bar of LEDs on the shift register.
0 of 4 steps
Drive a one-digit display from the 74HC595, one bit per segment, and count down from 9 to 0.
0 of 4 steps
Four digits share their segment pins and take turns, four milliseconds each, faster than your eye can follow.
0 of 4 steps
A DC motor both ways, a relay and a stepper, finished on the remote.
An H-bridge chip turns a motor forward, backward and off, with the speed set by PWM.
0 of 4 steps
A transistor drives the relay coil, a diode protects it, and the relay’s contacts switch a separate circuit.
0 of 4 steps
A stepper turns a precise number of steps. Drive the 28BYJ-48 from its ULN2003 board and point it with a knob.
0 of 4 steps
Put two lessons together: VOL+ and VOL- on the remote turn the stepper a quarter turn each way.
0 of 4 steps
All 24 lessons, in order, each with what it covers. Any of them opens in the editor right away.
Starter kit companion: the 24-lesson kit is part of the maker track, a ladder of courses from zero to expert.
Follows the lessons in the Elegoo Uno R3 Most Complete Starter Kit tutorial, in its order, each one running in your browser.
Open the next courseFollow the starter kit you already own, then build a claw machine, a balance bot, a handheld console or an LED cube, each a short course checked by the simulator.
See every course on the trackEvery lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.
6 lessons of this kit's manual are in this course.
Every lesson of the kit6 lessons of this kit's manual are in this course.
Every lesson of the kit5 lessons of this kit's manual are in this course.
Every lesson of the kitPick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kitYes. All 24 lessons of Starter kit companion: the 24-lesson kit are free and run in your browser, with nothing to install and no parts to buy before you start.
No. Every lesson runs on a simulated Arduino Uno R3 with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.
About 14 hours: 24 lessons in 5 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.
Each chapter ends in a project that puts it together: Kit: a button that lights an LED, Kit: sweeping a servo, Kit: decoding an IR remote, Kit: four digits by multiplexing and Kit: a stepper on the IR remote.
With "Making the board talk", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.