All paths

Starter kit companion: the 33-lesson kit

Follows the lessons in the Elegoo Uno R3 Most Complete Starter Kit tutorial, in its order, each one running in your browser.

Arduino Uno R3Free33 lessons20 h6 chapters4,475 XPMaker · Beginner+100 XP

0 of 33 done

What you will build

6 projects, built step by step

33 lessons in 6 chapters, about 20 hours on a simulated Arduino Uno R3. Free, in your browser, every step checked by the simulator.

Chapter 1 project

Kit: a button that lights an LED

Read a pushbutton with the chip’s own pull-up resistor and light an LED only while it is held.

Open it in the simulator
Chapter 2 project

Kit: sweeping a servo

A servo turns to an angle and holds it. Send it to 0, 90 and 180 degrees, then sweep it back one degree at a time.

Open it in the simulator
Chapter 3 project

Kit: an 8x8 LED matrix on a MAX7219

Sixty-four LEDs on three wires. The MAX7219 scans the rows itself; the sketch only draws.

Open it in the simulator
Chapter 4 project

Kit: an RFID card reader

The RC522 reads a card’s ID over SPI. Check it against a list and open the door for the right ones.

Open it in the simulator
Chapter 5 project

Kit: four digits by multiplexing

Four digits share their segment pins and take turns, four milliseconds each, faster than your eye can follow.

Open it in the simulator
Chapter 6 project

Kit: a stepper on a rotary encoder

An encoder counts clicks in either direction. Steer the stepper click for click, with interrupts doing the counting.

Open it in the simulator
The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

First steps

Print, blink, light an LED, mix colors and read a button.

  1. Open160 XP

    Making the board talk

    Printing is how you find out what a board thinks. What Serial.begin does, what a baud rate really costs, and how to print a number without lying about it.

    0 of 6 steps

  2. Locked140 XP

    Make it blink with an Uno

    Two wires from an Arduino Uno to the LED you already know, then press Run and let a program do the switching. Four steps, no code to write.

    0 of 4 steps

  3. Locked165 XP

    Build your first circuit

    Start with the parts in place. Draw every wire yourself, close the loop, press Run and light the LED.

    0 of 5 steps

  4. Locked110 XP

    Kit: mixing colors with an RGB LED

    Three LEDs under one lens. Fade red, green and blue with analogWrite and watch the colors in between appear.

    0 of 4 steps

  5. ProjectLocked220 XP

    Kit: a button that lights an LED

    Read a pushbutton with the chip’s own pull-up resistor and light an LED only while it is held.

    0 of 4 steps

Chapter 2

Sound and motion

Two kinds of buzzer, a tilt switch and a servo.

  1. Locked110 XP

    Kit: an active buzzer

    A buzzer with its own oscillator: power it and it sounds. The sketch only decides when.

    0 of 4 steps

  2. Locked110 XP

    Kit: playing notes on a passive buzzer

    A passive buzzer makes no sound on its own. tone() switches the pin at a note’s frequency and plays a tune.

    0 of 4 steps

  3. Locked110 XP

    Kit: a ball tilt switch

    A little ball that closes a contact while it stands up. Read it, filter its bounce, and light an LED when it tips.

    0 of 4 steps

  4. ProjectLocked220 XP

    Kit: sweeping a servo

    A servo turns to an angle and holds it. Send it to 0, 90 and 180 degrees, then sweep it back one degree at a time.

    0 of 4 steps

Chapter 3

Sensors and modules

Distance, a keypad, temperature, a joystick, a remote and an LED matrix.

  1. Locked110 XP

    Kit: measuring distance with sound

    The HC-SR04 times an echo. Turn the time into centimeters, then beep faster as something comes closer.

    0 of 4 steps

  2. Locked110 XP

    Kit: a keypad lock

    Scan a 4x4 membrane keypad row by row, collect a code, and open a relay when it is right.

    0 of 4 steps

  3. Locked110 XP

    Kit: temperature and humidity with a DHT11

    A sensor with its own little chip, read over one wire. Print the temperature and the humidity every two seconds.

    0 of 4 steps

  4. Locked110 XP

    Kit: reading a thumb joystick

    A joystick is two knobs and a button. Read both axes with analogRead and draw the position on a bar of LEDs.

    0 of 4 steps

  5. Locked110 XP

    Kit: decoding an IR remote

    The receiver turns flashes of infrared into pulses, and the IRremote library turns the pulses into a button’s code.

    0 of 4 steps

  6. ProjectLocked220 XP

    Kit: an 8x8 LED matrix on a MAX7219

    Sixty-four LEDs on three wires. The MAX7219 scans the rows itself; the sketch only draws.

    0 of 4 steps

Chapter 4

More sensors

Tilt, motion, water, time, sound and RFID cards.

  1. Locked110 XP

    Kit: tilt with the GY-521 accelerometer

    The MPU6050 measures gravity on three axes. Turn that into an angle and light a lamp for each way it tips.

    0 of 4 steps

  2. Locked110 XP

    Kit: a PIR motion sensor

    The HC-SR501 sees warm things move and holds its output high. Copy it onto an LED.

    0 of 4 steps

  3. Locked110 XP

    Kit: a water level sensor

    Bare copper traces read deeper water as a higher voltage. Sort the reading into dry, low, half and full.

    0 of 4 steps

  4. Locked110 XP

    Kit: a real-time clock

    The DS1307 keeps the date and time on its own crystal. Read it over I2C once a second.

    0 of 4 steps

  5. Locked110 XP

    Kit: a clap switch with the sound sensor

    The sound sensor’s digital output fires on a loud noise. Toggle a lamp on each clap, and ignore the echoes.

    0 of 4 steps

  6. ProjectLocked220 XP

    Kit: an RFID card reader

    The RC522 reads a card’s ID over SPI. Check it against a list and open the door for the right ones.

    0 of 4 steps

Chapter 5

Displays

An LCD, a shift register, the serial monitor and seven-segment digits.

  1. Locked110 XP

    Kit: hello on a 16x2 LCD

    Wire the character display with six signal lines and the LiquidCrystal library, then count the seconds on it.

    0 of 4 steps

  2. Locked110 XP

    Kit: a thermistor thermometer

    A resistor that changes with temperature, a voltage divider, and the beta equation: degrees on the LCD.

    0 of 4 steps

  3. Locked110 XP

    Kit: eight LEDs from three pins

    The 74HC595 shift register takes a byte one bit at a time and shows all eight bits at once.

    0 of 4 steps

  4. Locked160 XP

    Taking commands

    The monitor is an input too. Read characters without blocking, act on them, and answer everything, including the things you do not understand.

    0 of 6 steps

  5. Locked110 XP

    Kit: a photocell light meter

    A resistor that changes with light, read on A0, shown as a bar of LEDs on the shift register.

    0 of 4 steps

  6. Locked110 XP

    Kit: a countdown on a seven-segment digit

    Drive a one-digit display from the 74HC595, one bit per segment, and count down from 9 to 0.

    0 of 4 steps

  7. ProjectLocked220 XP

    Kit: four digits by multiplexing

    Four digits share their segment pins and take turns, four milliseconds each, faster than your eye can follow.

    0 of 4 steps

Chapter 6

Motors

A DC motor, a relay and a stepper, on a remote and on a knob.

  1. Locked110 XP

    Kit: a DC motor both ways with the L293D

    An H-bridge chip turns a motor forward, backward and off, with the speed set by PWM.

    0 of 4 steps

  2. Locked110 XP

    Kit: switching a motor with a relay

    A transistor drives the relay coil, a diode protects it, and the relay’s contacts switch a separate circuit.

    0 of 4 steps

  3. Locked110 XP

    Kit: a stepper motor that follows a knob

    A stepper turns a precise number of steps. Drive the 28BYJ-48 from its ULN2003 board and point it with a knob.

    0 of 4 steps

  4. Locked110 XP

    Kit: a stepper on the IR remote

    Put two lessons together: VOL+ and VOL- on the remote turn the stepper a quarter turn each way.

    0 of 4 steps

  5. ProjectLocked220 XP

    Kit: a stepper on a rotary encoder

    An encoder counts clicks in either direction. Steer the stepper click for click, with interrupts doing the counting.

    0 of 4 steps

Syllabus

Every lesson in the course

All 33 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

First steps

  1. Making the board talkPrinting is how you find out what a board thinks. What Serial.begin does, what a baud rate really costs, and how to print a number without lying about it.
  2. Make it blink with an UnoTwo wires from an Arduino Uno to the LED you already know, then press Run and let a program do the switching. Four steps, no code to write.
  3. Build your first circuitStart with the parts in place. Draw every wire yourself, close the loop, press Run and light the LED.
  4. Kit: mixing colors with an RGB LEDThree LEDs under one lens. Fade red, green and blue with analogWrite and watch the colors in between appear.
  5. Kit: a button that lights an LEDRead a pushbutton with the chip’s own pull-up resistor and light an LED only while it is held.
Chapter 2

Sound and motion

  1. Kit: an active buzzerA buzzer with its own oscillator: power it and it sounds. The sketch only decides when.
  2. Kit: playing notes on a passive buzzerA passive buzzer makes no sound on its own. tone() switches the pin at a note’s frequency and plays a tune.
  3. Kit: a ball tilt switchA little ball that closes a contact while it stands up. Read it, filter its bounce, and light an LED when it tips.
  4. Kit: sweeping a servoA servo turns to an angle and holds it. Send it to 0, 90 and 180 degrees, then sweep it back one degree at a time.
Chapter 3

Sensors and modules

  1. Kit: measuring distance with soundThe HC-SR04 times an echo. Turn the time into centimeters, then beep faster as something comes closer.
  2. Kit: a keypad lockScan a 4x4 membrane keypad row by row, collect a code, and open a relay when it is right.
  3. Kit: temperature and humidity with a DHT11A sensor with its own little chip, read over one wire. Print the temperature and the humidity every two seconds.
  4. Kit: reading a thumb joystickA joystick is two knobs and a button. Read both axes with analogRead and draw the position on a bar of LEDs.
  5. Kit: decoding an IR remoteThe receiver turns flashes of infrared into pulses, and the IRremote library turns the pulses into a button’s code.
  6. Kit: an 8x8 LED matrix on a MAX7219Sixty-four LEDs on three wires. The MAX7219 scans the rows itself; the sketch only draws.
Chapter 4

More sensors

  1. Kit: tilt with the GY-521 accelerometerThe MPU6050 measures gravity on three axes. Turn that into an angle and light a lamp for each way it tips.
  2. Kit: a PIR motion sensorThe HC-SR501 sees warm things move and holds its output high. Copy it onto an LED.
  3. Kit: a water level sensorBare copper traces read deeper water as a higher voltage. Sort the reading into dry, low, half and full.
  4. Kit: a real-time clockThe DS1307 keeps the date and time on its own crystal. Read it over I2C once a second.
  5. Kit: a clap switch with the sound sensorThe sound sensor’s digital output fires on a loud noise. Toggle a lamp on each clap, and ignore the echoes.
  6. Kit: an RFID card readerThe RC522 reads a card’s ID over SPI. Check it against a list and open the door for the right ones.
Chapter 5

Displays

  1. Kit: hello on a 16x2 LCDWire the character display with six signal lines and the LiquidCrystal library, then count the seconds on it.
  2. Kit: a thermistor thermometerA resistor that changes with temperature, a voltage divider, and the beta equation: degrees on the LCD.
  3. Kit: eight LEDs from three pinsThe 74HC595 shift register takes a byte one bit at a time and shows all eight bits at once.
  4. Taking commandsThe monitor is an input too. Read characters without blocking, act on them, and answer everything, including the things you do not understand.
  5. Kit: a photocell light meterA resistor that changes with light, read on A0, shown as a bar of LEDs on the shift register.
  6. Kit: a countdown on a seven-segment digitDrive a one-digit display from the 74HC595, one bit per segment, and count down from 9 to 0.
  7. Kit: four digits by multiplexingFour digits share their segment pins and take turns, four milliseconds each, faster than your eye can follow.
Chapter 6

Motors

  1. Kit: a DC motor both ways with the L293DAn H-bridge chip turns a motor forward, backward and off, with the speed set by PWM.
  2. Kit: switching a motor with a relayA transistor drives the relay coil, a diode protects it, and the relay’s contacts switch a separate circuit.
  3. Kit: a stepper motor that follows a knobA stepper turns a precise number of steps. Drive the 28BYJ-48 from its ULN2003 board and point it with a knob.
  4. Kit: a stepper on the IR remotePut two lessons together: VOL+ and VOL- on the remote turn the stepper a quarter turn each way.
  5. Kit: a stepper on a rotary encoderAn encoder counts clicks in either direction. Steer the stepper click for click, with interrupts doing the counting.
Keep going

The next course on your track

Starter kit companion: the 33-lesson kit is part of the maker track, a ladder of courses from zero to expert.

Next course

Build a 4x4x4 LED cube

Sixty-four LEDs from twenty wires in three builds: a shift register, multiplexing slowed down, then a cube full of animations.

Open the next course
Track

Maker track

Follow the starter kit you already own, then build a claw machine, a balance bot, a handheld console or an LED cube, each a short course checked by the simulator.

See every course on the track
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

Starter kit

ELEGOO UNO R3 Most Complete Starter Kit

10 lessons of this kit's manual are in this course.

Every lesson of the kit
Starter kit

ELEGOO UNO R3 Super Starter Kit

6 lessons of this kit's manual are in this course.

Every lesson of the kit
Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About Starter kit companion: the 33-lesson kit

Is Starter kit companion: the 33-lesson kit free?

Yes. All 33 lessons of Starter kit companion: the 33-lesson kit are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real Arduino Uno R3?

No. Every lesson runs on a simulated Arduino Uno R3 with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Starter kit companion: the 33-lesson kit take?

About 20 hours: 33 lessons in 6 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: Kit: a button that lights an LED, Kit: sweeping a servo, Kit: an 8x8 LED matrix on a MAX7219, Kit: an RFID card reader, Kit: four digits by multiplexing and Kit: a stepper on a rotary encoder.

Where do I start?

With "Making the board talk", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.