All paths

Starter kit companion: the project book

Follows the fifteen projects in the official Arduino Starter Kit book, in its order, each one running in your browser.

Arduino Uno R3Free15 lessons10 h4 chapters2,145 XPMaker · Beginner+100 XP

0 of 15 done

Start the course freeBuild your first circuitBuild it as a kitRetails for about $48, free on Mokxi.Lesson plan for teachers
What you will build

4 projects, built step by step

15 lessons in 4 chapters, about 10 hours on a simulated Arduino Uno R3. Free, in your browser, every step checked by the simulator.

Chapter 1 project

Kit: a color-mixing lamp

Three light sensors behind colored gels set the red, green and blue of one LED.

Open it in the simulator
Chapter 2 project

Kit: a tilt hourglass

Six LEDs light on a millis() timer while the sketch keeps watching a tilt switch to start again.

Open it in the simulator
Chapter 3 project

Kit: a spinning zoetrope

The L293D H-bridge runs the motor either way, a button starts and stops it, and a knob sets the speed.

Open it in the simulator
Chapter 4 project

Kit: pressing a button with an optocoupler

An LED and a light sensor in one chip let the board press another gadget’s button without sharing a wire.

Open it in the simulator
The map

Chapter by chapter

Each lesson opens when the one before it is done, and each chapter ends in a project.

Chapter 1

First lights

Wire a loop, read a button and a sensor, and mix colors.

  1. Open165 XP

    Build your first circuit

    Start with the parts in place. Draw every wire yourself, close the loop, press Run and light the LED.

    0 of 5 steps

  2. Locked110 XP

    Kit: a starship control panel

    A green lamp waits, and two red lamps flash while you hold the button. Your first if and else, and a pull-down resistor.

    0 of 4 steps

  3. Locked110 XP

    Kit: a warm-hands meter

    A TMP36 temperature sensor, three LEDs and some floating-point math: squeeze the sensor and watch the lights climb.

    0 of 4 steps

  4. ProjectLocked220 XP

    Kit: a color-mixing lamp

    Three light sensors behind colored gels set the red, green and blue of one LED.

    0 of 4 steps

Chapter 2

Motion and sound

Point a servo, play light as a note, and build a keyboard on one pin.

  1. Locked110 XP

    Kit: a mood dial

    Turn a potentiometer and a servo points to match. map() turns one range of numbers into another.

    0 of 4 steps

  2. Locked110 XP

    Kit: a light theremin

    Light on a phototransistor becomes a pitch on a piezo. Wave your hand over it to play.

    0 of 4 steps

  3. Locked110 XP

    Kit: a four-key keyboard

    Four buttons share one analog pin through a ladder of resistors, and a piezo plays a note for each.

    0 of 4 steps

  4. ProjectLocked220 XP

    Kit: a tilt hourglass

    Six LEDs light on a millis() timer while the sketch keeps watching a tilt switch to start again.

    0 of 4 steps

Chapter 3

Motors

Switch a motor with a MOSFET, then run one both ways with an H-bridge.

  1. Locked110 XP

    Kit: a motor pinwheel

    A MOSFET lets a pin switch a motor on a 9 V battery, and a diode catches the motor’s kick.

    0 of 4 steps

  2. ProjectLocked220 XP

    Kit: a spinning zoetrope

    The L293D H-bridge runs the motor either way, a button starts and stops it, and a knob sets the speed.

    0 of 4 steps

Chapter 4

Bigger builds

An answer ball, a knock lock, a touch lamp, and talking to other things.

  1. Locked110 XP

    Kit: an answer ball

    Ask a question, tip the tilt switch, and the LCD shows an answer picked with random().

    0 of 4 steps

  2. Locked110 XP

    Kit: a secret knock lock

    Listen for a rhythm of knocks and slide a servo bolt open only for the right one.

    0 of 4 steps

  3. Locked110 XP

    Kit: a touch lamp

    A piece of foil and a 1 megohm resistor make a touch sensor, read with the CapacitiveSensor library.

    0 of 4 steps

  4. Locked110 XP

    Kit: sending a knob to your computer

    Read a potentiometer and send the number over serial, the board’s half of talking to a program on your computer.

    0 of 4 steps

  5. ProjectLocked220 XP

    Kit: pressing a button with an optocoupler

    An LED and a light sensor in one chip let the board press another gadget’s button without sharing a wire.

    0 of 4 steps

Syllabus

Every lesson in the course

All 15 lessons, in order, each with what it covers. Any of them opens in the editor right away.

Chapter 1

First lights

  1. Build your first circuitStart with the parts in place. Draw every wire yourself, close the loop, press Run and light the LED.
  2. Kit: a starship control panelA green lamp waits, and two red lamps flash while you hold the button. Your first if and else, and a pull-down resistor.
  3. Kit: a warm-hands meterA TMP36 temperature sensor, three LEDs and some floating-point math: squeeze the sensor and watch the lights climb.
  4. Kit: a color-mixing lampThree light sensors behind colored gels set the red, green and blue of one LED.
Chapter 2

Motion and sound

  1. Kit: a mood dialTurn a potentiometer and a servo points to match. map() turns one range of numbers into another.
  2. Kit: a light thereminLight on a phototransistor becomes a pitch on a piezo. Wave your hand over it to play.
  3. Kit: a four-key keyboardFour buttons share one analog pin through a ladder of resistors, and a piezo plays a note for each.
  4. Kit: a tilt hourglassSix LEDs light on a millis() timer while the sketch keeps watching a tilt switch to start again.
Chapter 3

Motors

  1. Kit: a motor pinwheelA MOSFET lets a pin switch a motor on a 9 V battery, and a diode catches the motor’s kick.
  2. Kit: a spinning zoetropeThe L293D H-bridge runs the motor either way, a button starts and stops it, and a knob sets the speed.
Chapter 4

Bigger builds

  1. Kit: an answer ballAsk a question, tip the tilt switch, and the LCD shows an answer picked with random().
  2. Kit: a secret knock lockListen for a rhythm of knocks and slide a servo bolt open only for the right one.
  3. Kit: a touch lampA piece of foil and a 1 megohm resistor make a touch sensor, read with the CapacitiveSensor library.
  4. Kit: sending a knob to your computerRead a potentiometer and send the number over serial, the board’s half of talking to a program on your computer.
  5. Kit: pressing a button with an optocouplerAn LED and a light sensor in one chip let the board press another gadget’s button without sharing a wire.
Keep going

The next course on your track

Starter kit companion: the project book is part of the maker track, a ladder of courses from zero to expert.

Next course

Starter kit companion: the 24-lesson kit

Follows the lessons in the Elegoo Uno R3 Super Starter Kit tutorial, in its order, each one running in your browser.

Open the next course
Track

Maker track

Follow the starter kit you already own, then build a claw machine, a balance bot, a handheld console or an LED cube, each a short course checked by the simulator.

See every course on the track
Kits

Build it on your bench too

Every lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.

The kit for this course

Starter Projects Kit

The starter kit book, part one: an Uno, LEDs, light and heat sensors, a servo, a piezo and four keys.

Open the kit
Have a kit already?

Find your kit

Pick the starter kit you own and run every lesson in its manual with the same parts on the same pins.

See every kit
Questions

About Starter kit companion: the project book

Is Starter kit companion: the project book free?

Yes. All 15 lessons of Starter kit companion: the project book are free and run in your browser, with nothing to install and no parts to buy before you start.

Do I need a real Arduino Uno R3?

No. Every lesson runs on a simulated Arduino Uno R3 with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.

How long does Starter kit companion: the project book take?

About 10 hours: 15 lessons in 4 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.

What will I build?

Each chapter ends in a project that puts it together: Kit: a color-mixing lamp, Kit: a tilt hourglass, Kit: a spinning zoetrope and Kit: pressing a button with an optocoupler.

Where do I start?

With "Build your first circuit", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.