How to wire an RC522 RFID reader to an ESP32-C3
To wire an RC522 RFID reader to an ESP32-C3, connect 3.3V to 3V3, GND to GND, SDA to GPIO 7, SCK to GPIO 4, MOSI to GPIO 6, MISO to GPIO 5 and RST to GPIO 10. The ESP32-C3 and the MFRC522 are both 3.3 V, so the SPI lines connect directly. The sketch below uses the MFRC522 (MFRC522.h) library. It reads the card that is held to the reader and prints its UID.
- 3.3 V logic
- Library: MFRC522.h
- 7 wires
RC522 RFID reader to ESP32-C3 wiring table
Every wire in the circuit above, with the part’s pin names and the board’s own labels. The wire colors are the ones the circuit uses; on a real bench any colors work.
| RC522 RFID reader pin | ESP32-C3 pin | Wire color | Why |
|---|---|---|---|
| 3.3V | 3V3 | red | The MFRC522 is a 3.3 V chip. Never 5 V on this pin. |
| GND | GND | blue | Common ground. |
| SDA (SS) | GPIO 7 | amber | Chip select. Labeled SDA on the module, but this is SPI, not I2C. |
| SCK | GPIO 4 | cyan | ESP32-C3’s SPI clock. |
| MOSI | GPIO 6 | violet | Data from the board to the reader. |
| MISO | GPIO 5 | green | Data from the reader to the board. |
| RST | GPIO 10 | gray | Reset, held high while the reader runs. |
| IRQ | not connected | n/a | The library polls instead. |
Power and logic levels for RC522 RFID reader and ESP32-C3
Logic level
The ESP32-C3’s GPIO pins are 3.3 V logic and are not 5 V tolerant. Nothing wired to a pin may go above 3.3 V.
Supply
The RC522 RFID reader takes 3.3 V from 3V3. That pin is the ESP32-C3’s own regulated 3.3 V output.
This pair
The ESP32-C3 and the MFRC522 are both 3.3 V, so the SPI lines connect directly: the cleanest RC522 wiring there is.
Pins to leave alone
GPIO 8 carries the onboard LED and GPIO 9 is the BOOT button, and both are also the default I2C pins. GPIO 2, 8 and 9 are strapping pins, and only GPIO 0 to 4 can read an analog voltage.
The working code for the ESP32-C3
Library: MFRC522 (MFRC522.h). This is the sketch the circuit above runs.
#include <SPI.h>
#include <MFRC522.h>
const int SS_PIN = 7; // SDA on the module, GPIO 7
const int RST_PIN = 10; // GPIO 10
MFRC522 rfid(SS_PIN, RST_PIN);
void setup() {
Serial.begin(115200);
SPI.begin(); // SCK 4, MISO 5, MOSI 6
rfid.PCD_Init();
Serial.println("Hold a card to the reader");
}
void loop() {
if (!rfid.PICC_IsNewCardPresent() || !rfid.PICC_ReadCardSerial()) {
delay(50);
return;
}
Serial.print("Card UID:");
for (byte i = 0; i < rfid.uid.size; i++) {
Serial.print(rfid.uid.uidByte[i] < 0x10 ? " 0" : " ");
Serial.print(rfid.uid.uidByte[i], HEX);
}
Serial.println();
rfid.PICC_HaltA(); // done with this card until it is lifted
}
What you should see
Open the serial monitor at 115200 baud. The sketch prints Hold a card to the reader and, when you present the card in the circuit, a Card UID line with its four bytes in hexadecimal.
The pin labeled SDA on the module is the SPI chip select, not an I2C line. IRQ is left unconnected because the library polls.
The serial monitor prints this, recorded from the circuit above with a card presented after 400 ms:
Hold a card to the reader
Card UID: C3 5A 1E 94Common mistakes wiring an RC522 RFID reader to an ESP32-C3
Powering it from 5V
The 3.3V pin means it: 5 V there damages the MFRC522. If the module gets warm or reports a version of 0x00 or 0xFF, check this first.
Treating SDA as I2C
The pin marked SDA is the SPI chip select. Wired to the ESP32-C3’s I2C data pin, the reader is never selected. It goes to SS_PIN, GPIO 7 here.
Expecting to read bank cards
The RC522 reads 13.56 MHz MIFARE tags and cards. Contactless bank cards answer, but only with a random ID each time, and 125 kHz key fobs not at all.
Build your own RC522 RFID reader project
Open this circuit in the editor, change the wiring or the code, and keep your version in a free account.