How to wire a DHT22 to an ESP32-C3
To wire a DHT22 to an ESP32-C3, connect VCC to 3V3, DATA to GPIO 4 and GND to GND. The ESP32-C3 is a 3.3 V board, so power the sensor from 3.3 V: the module’s built-in pull-up then keeps DATA at 3.3 V, which the pin can take. The sketch below uses the Adafruit DHT sensor library (DHT.h) library. It prints the temperature and the humidity on the serial monitor every two seconds.
- 3.3 V logic
- Library: DHT.h
- 3 wires
DHT22 to ESP32-C3 wiring table
Every wire in the circuit above, with the part’s pin names and the board’s own labels. The wire colors are the ones the circuit uses; on a real bench any colors work.
| DHT22 pin | ESP32-C3 pin | Wire color | Why |
|---|---|---|---|
| VCC (+) | 3V3 | red | The sensor runs from 3.3 V, and so does its pull-up, so DATA never rises above what the pin can take. |
| DATA (out) | GPIO 4 | amber | One wire, both directions: the board pulls it low to ask, the sensor answers with 40 bits. |
| GND (-) | GND | blue | A shared ground, or the board cannot read the sensor’s levels. |
Power and logic levels for DHT22 and ESP32-C3
Logic level
The ESP32-C3’s GPIO pins are 3.3 V logic and are not 5 V tolerant. Nothing wired to a pin may go above 3.3 V.
Supply
The DHT22 takes 3.3 V from 3V3. That pin is the ESP32-C3’s own regulated 3.3 V output.
This pair
The three-pin module carries a pull-up resistor from DATA to VCC. Powered from 5V, that resistor would hold a ESP32-C3 pin at 5 V, which the ESP32-C3 (RISC-V) is not rated for. From 3V3 the whole line stays at 3.3 V and the sensor still reads normally.
Pins to leave alone
GPIO 8 carries the onboard LED and GPIO 9 is the BOOT button, and both are also the default I2C pins. GPIO 2, 8 and 9 are strapping pins, and only GPIO 0 to 4 can read an analog voltage.
The working code for the ESP32-C3
Library: Adafruit DHT sensor library (DHT.h). This is the sketch the circuit above runs.
#include "DHT.h"
#define DHT_PIN 4 // DATA, GPIO 4
#define DHT_TYPE DHT22
DHT dht(DHT_PIN, DHT_TYPE);
void setup() {
Serial.begin(115200);
dht.begin();
Serial.println("DHT22 on the ESP32-C3");
}
void loop() {
delay(2000); // the DHT22 measures every 2 s
float celsius = dht.readTemperature();
float humidity = dht.readHumidity();
if (isnan(celsius) || isnan(humidity)) { // a failed read is NAN
Serial.println("No reading from the DHT22");
return;
}
Serial.print("Temperature: ");
Serial.print(celsius, 1);
Serial.print(" C Humidity: ");
Serial.print(humidity, 1);
Serial.println(" %");
}
What you should see
Open the serial monitor at 115200 baud. The sketch waits two seconds, which is how often a DHT22 can measure, and then prints one line per reading. The sensor starts at 22 degrees C and 50 percent humidity, and the line follows its two sliders when you drag them.
If a read fails the sketch prints No reading from the DHT22 instead of a number. That is what a wrong DATA pin or a missing pull-up looks like.
The serial monitor prints this, recorded from the circuit above left at its defaults:
DHT22 on the ESP32-C3
Temperature: 22.0 C Humidity: 50.0 %Common mistakes wiring a DHT22 to an ESP32-C3
Reading faster than every two seconds
A DHT22 needs two seconds between measurements. Ask sooner and it returns the previous reading, or nothing at all, so a fast loop looks like a stuck sensor. Keep the delay(2000), or time the reads with millis().
Powering the module from 5V
It works for a while, which is the trap. The module’s pull-up then holds DATA at 5 V, above the ESP32-C3 (RISC-V)’s absolute maximum, and the pin can be damaged slowly. Use 3V3, as in the circuit above.
Using GPIO 8 or 9
GPIO 8 drives the onboard LED and GPIO 9 is the BOOT button, and both are strapping pins read at power-on. Wired to the DHT22’s DATA line, either can stop a real board from booting. GPIO 4 and GPIO 5 are free of both.
Build your own DHT22 project
Open this circuit in the editor, change the wiring or the code, and keep your version in a free account.