Pressure and cold
Turn pressure into altitude with the three layers of the standard atmosphere, then find where the BMP280 runs out of range and why batteries hate the tropopause.
Open it in the simulatorBuild the payload that rides a balloon to 30 km: GPS in flight mode, pressure and cold, LoRa tracking, a flight log, a cutdown and a whole simulated flight.
0 of 6 done
6 lessons in 3 chapters, about 6 hours on a simulated Arduino Uno R3. Free, in your browser, every step checked by the simulator.
Turn pressure into altitude with the three layers of the standard atmosphere, then find where the BMP280 runs out of range and why batteries hate the tropopause.
Open it in the simulatorWrite GPS, pressure and temperature to a CSV file on microSD every two seconds, flush it so a dead battery loses nothing, and keep flying without a card.
Open it in the simulatorFly a whole balloon flight, 300 times faster than life: launch, the tropopause, burst at 30 km, the parachute, landing, with telemetry, a log and a cutdown.
Open it in the simulatorEach lesson opens when the one before it is done, and each chapter ends in a project.
GPS altitude in flight mode, and the standard atmosphere.
Read altitude from a NEO-6M, and send the one UBX command every balloon needs: airborne mode, or the fix disappears at 12 km.
0 of 5 steps
Turn pressure into altitude with the three layers of the standard atmosphere, then find where the BMP280 runs out of range and why batteries hate the tropopause.
0 of 5 steps
Sentences a stranger can check, and a log that misses nothing.
Send a UKHAS position sentence with a CRC16 every five seconds, so any receiver on the ground can check it and put the balloon on a map.
0 of 5 steps
Write GPS, pressure and temperature to a CSV file on microSD every two seconds, flush it so a dead battery loses nothing, and keep flying without a card.
0 of 5 steps
A cutdown that never fires on the ground, then launch to landing.
Cut the balloon away on purpose with a MOSFET and a nichrome stand-in: on a ceiling, a geofence or a command, and never on the ground.
0 of 7 steps
Fly a whole balloon flight, 300 times faster than life: launch, the tropopause, burst at 30 km, the parachute, landing, with telemetry, a log and a cutdown.
0 of 7 steps
All 6 lessons, in order, each with what it covers. Any of them opens in the editor right away.
Build a high-altitude balloon tracker is part of the maker track, a ladder of courses from zero to expert.
From a CPU of NAND gates to a machine with a keyboard, a screen, a hex monitor and a BASIC that saves your programs.
Open the next courseFollow the starter kit you already own, then build a claw machine, a balance bot, a handheld console or an LED cube, each a short course checked by the simulator.
See every course on the trackEvery lesson runs in the simulator with nothing to buy. When you want the real thing, these kits have the parts.
An Uno, a LoRa module (SX1278, Ra-02) and a GPS module (NEO-6M): a tracker that logs a balloon flight and cuts it down on command.
Open the kitPick the starter kit you own and run every lesson in its manual with the same parts on the same pins.
See every kitYes. All 6 lessons of Build a high-altitude balloon tracker are free and run in your browser, with nothing to install and no parts to buy before you start.
No. Every lesson runs on a simulated Arduino Uno R3 with its parts on the canvas, and the simulator checks each step as you go. When you want to build it for real, the same wiring and code work on a real board.
About 6 hours: 6 lessons in 3 chapters, each one a few short steps. Your progress is kept, so you can stop after any lesson and pick up where you left off.
Each chapter ends in a project that puts it together: Pressure and cold, Logging and Project: a simulated flight.
With "GPS altitude", and each lesson builds on the one before it. New to circuits? Electronics basics is the course that starts from zero.