Lesson plan

Build a high-altitude balloon tracker lesson plan

Build the payload that rides a balloon to 30 km: GPS in flight mode, pressure and cold, LoRa tracking, a flight log, a cutdown and a whole simulated flight.

3 chapters, 6 lessons, about 6 hours, on the Arduino Uno R3. Every lesson runs in the browser, with nothing to install.

The unit

Objectives and materials

By the end, students can

  • GPS altitude in flight mode, and the standard atmosphere.
  • Sentences a stranger can check, and a log that misses nothing.
  • A cutdown that never fires on the ground, then launch to landing.

Materials for the whole unit

  • Arduino Uno R3
  • Battery: AA, coin cell, LiPo
  • Filament lamp
  • Full-size breadboard
  • GPS module, NEO-6M
  • LoRa module, SX1278 (Ra-02)
  • microSD card module
  • MOSFET
  • Pressure and temperature, BMP280
  • Resistor

Every part is already on the simulator’s bench, so there is nothing to buy or hand out. The counts are the most any one lesson uses, if you build it on real breadboards too.

Chapter 1. About 1 h 50 min

How high, how cold

GPS altitude in flight mode, and the standard atmosphere.

LessonTimeWhat students do
GPS altitudeRead altitude from a NEO-6M, and send the one UBX command every balloon needs: airborne mode, or the fix disappears at 12 km.55 min
  1. Meet the tracker
  2. A binary command
  3. A fix on the ground
  4. Climb past 12 km
  5. Lose the sky
Pressure and coldTurn pressure into altitude with the three layers of the standard atmosphere, then find where the BMP280 runs out of range and why batteries hate the tropopause.55 min
  1. Find the barometer
  2. The standard atmosphere
  3. Climb to 700 hPa
  4. The end of the scale
  5. Cold

Materials

  • Arduino Uno R3
  • Battery: AA, coin cell, LiPo
  • Filament lamp
  • Full-size breadboard
  • GPS module, NEO-6M
  • LoRa module, SX1278 (Ra-02)
  • microSD card module
  • MOSFET
  • Pressure and temperature, BMP280
  • Resistor

Check for understanding

Each student finishes "Pressure and cold" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Cold".

Chapter 2. About 1 h 50 min

Track it, keep it

Sentences a stranger can check, and a log that misses nothing.

LessonTimeWhat students do
LoRa trackingSend a UKHAS position sentence with a CRC16 every five seconds, so any receiver on the ground can check it and put the balloon on a map.55 min
  1. Check the checker
  2. The radio
  3. A sentence
  4. On the air
  5. Higher
LoggingWrite GPS, pressure and temperature to a CSV file on microSD every two seconds, flush it so a dead battery loses nothing, and keep flying without a card.55 min
  1. Open the log
  2. One line every two seconds
  3. Flush
  4. Pressure in the log
  5. No card

Materials

  • Arduino Uno R3
  • Battery: AA, coin cell, LiPo
  • Filament lamp
  • Full-size breadboard
  • GPS module, NEO-6M
  • LoRa module, SX1278 (Ra-02)
  • microSD card module
  • MOSFET
  • Pressure and temperature, BMP280
  • Resistor

Check for understanding

Each student finishes "Logging" on their own, without opening the hints. The simulator checks 5 of its 5 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "No card".

Chapter 3. About 2 h 30 min

Fly it

A cutdown that never fires on the ground, then launch to landing.

LessonTimeWhat students do
A cutdownCut the balloon away on purpose with a MOSFET and a nichrome stand-in: on a ceiling, a geofence or a command, and never on the ground.75 min
  1. Safe on the ground
  2. Not on the ground
  3. Armed in flight
  4. The ceiling
  5. The nichrome glows
  6. By command
  7. The geofence
Project: a simulated flightFly a whole balloon flight, 300 times faster than life: launch, the tropopause, burst at 30 km, the parachute, landing, with telemetry, a log and a cutdown.75 min
  1. Launch
  2. The tropopause
  3. Burst
  4. Landing
  5. Cut it short
  6. Save the flight
  7. Before a real flight

Materials

  • Arduino Uno R3
  • Battery: AA, coin cell, LiPo
  • Filament lamp
  • Full-size breadboard
  • GPS module, NEO-6M
  • LoRa module, SX1278 (Ra-02)
  • microSD card module
  • MOSFET
  • Pressure and temperature, BMP280
  • Resistor

Check for understanding

Each student finishes "Project: a simulated flight" on their own, without opening the hints. The simulator checks 7 of its 7 steps as they go.

Then ask each one to explain, in a sentence or two, the last thing it asked of them: "Before a real flight".

Your class

Teach this unit as a class

Start a class from this course and its 6 lessons are assigned in one go, in order. Students join with a six-character code or printed login cards, and each one’s work comes back to you.

The class tools are free for 30 days for one class of up to 20 students, with no card. The lessons themselves are free either way.