Projects with a robot car chassis
14 Mokxi projects use a 2WD robot car chassis (1 beginner, 9 intermediate and 4 advanced). They run on Arduino Uno boards. Here are all of them, from “Light-seeking robot” to “Hand gesture controlled car”. Each card says what the project does, the board and parts it needs and its level, and Open in the simulator runs it in your browser in one click, with no account.
How to pick your first one
- Start with “Light-seeking robot”, a beginner project that needs an L298N motor driver, a robot car chassis and a light sensor module.
- All of them run on an Arduino Uno, so that is the one board you need.
- The parts used most here are the L298N motor driver (7 projects), the DRV8833 motor driver (4) and the HC-SR04 ultrasonic sensor (3). With those on hand, most of this list is open to you.
- Before you build one on a real bench, open the 2WD robot car chassis part page for its pins and what each one does.
14 projects ready to run

Light-seeking robot
A two-wheel robot with a photoresistor module on each front corner.
- Board
- Arduino Uno R3
- Parts
- L298N motor driver, 2WD robot car chassis, photoresistor module
- Level
- Beginner

Joystick robot car with an L298N
A thumb stick on A1 and A2 drives a 2WD car on an L298N like a tank: throttle plus steer on one wheel, minus on the other, and a press for slow mode.
- Board
- Arduino Uno R3
- Parts
- L298N motor driver, 2WD robot car chassis, joystick
- Level
- Intermediate

Obstacle-avoiding car
A 2WD robot car on an L298N with an HC-SR04 on the front. It drives ahead, and when something comes within 25 cm it backs up, turns and carries on.
- Board
- Arduino Uno R3
- Parts
- L298N motor driver, 2WD robot car chassis, HC-SR04 ultrasonic sensor
- Level
- Intermediate

Bumper car
A 2WD robot car on a DRV8833 with two lever microswitches for bumpers. It drives until a bumper is hit, then backs off and turns away from that side.
- Board
- Arduino Uno R3
- Parts
- DRV8833 motor driver, 2WD robot car chassis, limit switch
- Level
- Intermediate

Maze-solving robot
A two-wheel robot with three Sharp infrared distance sensors.
- Board
- Arduino Uno R3
- Parts
- DRV8833 motor driver, 2WD robot car chassis, IR distance sensor
- Level
- Intermediate

Bluetooth RC car with an HC-05
An HC-05 and a 2WD car on an L298N: type F, B, L, R or S in the module’s box, as a phone app sends them, and the car drives; 0 to 9 set the speed.
- Board
- Arduino Uno R3
- Parts
- L298N motor driver, 2WD robot car chassis, HC-05 Bluetooth module, resistor
- Level
- Intermediate

Infrared remote rover
A two-wheel robot driven from a 21-button infrared remote.
- Board
- Arduino Uno R3
- Parts
- MX1508 dual motor driver, 2WD robot car chassis, IR receiver and remote, IR remote
- Level
- Intermediate

Scanning obstacle rover
A robot with an ultrasonic sensor on a servo neck. Blocked, it stops, looks right, ahead and left, picks the clearest way and turns that way.
- Board
- Arduino Uno R3
- Parts
- TB6612FNG motor driver, 2WD robot car chassis, servo motor, HC-SR04 ultrasonic sensor
- Level
- Intermediate

Robot vacuum behaviors
A cleaning robot with two bumpers and a cliff sensor.
- Board
- Arduino Uno R3
- Parts
- DRV8833 motor driver, 2WD robot car chassis, limit switch, TCRT5000 line sensor
- Level
- Intermediate

Sumo robot
A mini-sumo robot with an ultrasonic eye and two edge sensors.
- Board
- Arduino Uno R3
- Parts
- DRV8833 motor driver, 2WD robot car chassis, HC-SR04 ultrasonic sensor, TCRT5000 line sensor
- Level
- Intermediate

Wheel-encoder square driver
A two-wheel robot that counts pulses from a slot sensor on each wheel.
- Board
- Arduino Uno R3
- Parts
- L9110S motor driver, 2WD robot car chassis
- Level
- Advanced

Mars rover
A rover that drives three waypoints by dead reckoning, steers around hazards it sees with a sonar mast, samples soil and light.
- Board
- Arduino Uno R3
- Parts
- L298N motor driver, 2WD robot car chassis, push button, SSD1306 OLED display, VL53L0X time-of-flight sensor, +3 more
- Level
- Advanced

Fire fighting robot
Three flame sensors steer a 2WD car on an L298N to the fire, then a relay runs a water pump while a servo sweeps the nozzle until the flame is out.
- Board
- Arduino Uno R3
- Parts
- L298N motor driver, 2WD robot car chassis, flame sensor, servo motor, relay module, +1 more
- Level
- Advanced

Hand gesture controlled car
Tilt an MPU6050 on your hand and a 2WD car follows over nRF24L01 radios: forward, reverse, left, right, and it stops when the signal is lost.
- Board
- Arduino Uno R3
- Parts
- NRF24L01+ 2.4 GHz radio, MPU6050 accelerometer and gyro, L298N motor driver, 2WD robot car chassis
- Level
- Advanced