Wiring guide

How to wire a buzzer to an Arduino Uno R4

To wire a buzzer to an Arduino Uno R4, connect 1 to pin 9 and 2 to GND. A small passive piezo draws a few milliamps, so it runs straight from the pin with its other leg on ground. The sketch below uses no library beyond what the board includes. It plays a four-note phrase and repeats it, printing Playing once and Again after each phrase.

  • 5 V logic
  • Library: none
  • 2 wires
Arduino Uno R4 · buzzerlive0.000 s 0.00x
Click to open it in the editor
The circuit itself, running on the simulator with the sketch below. Press what can be pressed; click anything else to open it in the editor.
Pin to pin

Buzzer to Arduino Uno R4 wiring table

Every wire in the circuit above, with the part’s pin names and the board’s own labels. The wire colors are the ones the circuit uses; on a real bench any colors work.

Buzzer pinArduino Uno R4 pinWire colorWhy
Pin 1pin 9ambertone() puts a square wave at the note’s frequency on this pin.
Pin 2GNDblueGround. A passive piezo has no polarity.
Voltage

Power and logic levels for buzzer and Arduino Uno R4

Logic level

The Arduino Uno R4’s pins are 5 V logic. A 5 V part can drive them directly; a part whose signal pins are limited to 3.3 V needs a level shifter.

This pair

A small passive piezo runs straight from a 5 V pin. On the Uno R4, tone() plays on the PWM pins, and the RA4M1’s pins source less current than an Uno’s, which a piezo does not mind but a magnetic buzzer does: switch that one through a transistor.

Pins to leave alone

An Uno sketch’s source builds for the R4, but a compiled Uno program will not run on it: different chip. The R4’s pins source less current than an Uno’s, about 8 mA each, so do not drive a relay coil or a motor straight from one.

The sketch

The working code for the Arduino Uno R4

Library: none, the sketch makes the note with tone(). This is the sketch the circuit above runs.

Tones on Arduino Uno R4 pin 9
const int BUZZER_PIN = 9;   // pin 9

// C, E, G, C: an arpeggio, a quarter second a note.
const int NOTES[] = {523, 659, 784, 1047};

void setup() {
  Serial.begin(9600);
  Serial.println("Playing");
}

void loop() {
  for (int i = 0; i < 4; i++) {
    tone(BUZZER_PIN, NOTES[i], 200);   // returns at once; the note plays on
    delay(250);
  }
  noTone(BUZZER_PIN);
  Serial.println("Again");
  delay(500);
}
Output

What you should see

The buzzer plays a short four-note phrase and then plays it again. The serial monitor, at 9600 baud, prints Playing at the start and Again after each phrase.

A buzzer that clicks once but never sounds a note is an active buzzer: it ignores tone() and needs only a HIGH level.

The serial monitor prints this, recorded from the circuit above running for two seconds:

Playing
Again
Pitfalls

Common mistakes wiring a buzzer to an Arduino Uno R4

An active buzzer

An active buzzer has its own oscillator and beeps at one pitch whenever it has power, so tone() cannot change its note. For melodies you need a passive one; the two look the same, but the active kind usually has a sticker on top.

No delay between notes

tone() does not wait for the note to finish. Call it twice in a row and only the second note plays. Wait at least as long as the note, as the sketch does.

Expecting an Uno’s pin current

The R4’s pins are 5 V like an Uno’s, but each one sources only about 8 mA where an Uno’s gives 20. A signal line to the buzzer is fine; an LED or a coil hung straight off the pin is not.

Build your own buzzer project

Open this circuit in the editor, change the wiring or the code, and keep your version in a free account.