Wiring guide

How to wire a relay module to an Arduino Uno R4

To wire a relay module to an Arduino Uno R4, connect VCC to 5V, GND to GND and IN to pin 2. The Arduino Uno R4 drives IN at 5 V and the module’s own transistor carries the coil current, so the pin only supplies a few milliamps. The sketch below uses no library beyond what the board includes. It switches the relay on for a second and off for a second, printing a line each time.

  • 5 V logic
  • Library: none
  • 3 wires
Arduino Uno R4 · relay modulelive0.000 s 0.00x
Click to open it in the editor
The circuit itself, running on the simulator with the sketch below. Press what can be pressed; click anything else to open it in the editor.
Pin to pin

Relay module to Arduino Uno R4 wiring table

Every wire in the circuit above, with the part’s pin names and the board’s own labels. The wire colors are the ones the circuit uses; on a real bench any colors work.

Relay module pinArduino Uno R4 pinWire colorWhy
VCC5VredThe coil is a 5 V coil; it takes about 70 mA, more than any pin can give.
GNDGNDblueCommon ground.
INpin 2amberA logic signal only: the module’s transistor switches the coil.
COM, NO, NCThe loadn/aThe switched side: COM is the arm, NO is open until the relay pulls in, NC is closed until then.
Voltage

Power and logic levels for relay module and Arduino Uno R4

Logic level

The Arduino Uno R4’s pins are 5 V logic. A 5 V part can drive them directly; a part whose signal pins are limited to 3.3 V needs a level shifter.

Supply

The relay module takes 5 V from 5V. That is the Arduino Uno R4’s 5 V rail, so the part shares the current the board can supply.

This pair

The Arduino Uno R4 drives IN at 5 V and the module’s own transistor carries the coil current, so the pin only supplies a few milliamps. The simulated relay triggers on HIGH; many blue modules trigger on LOW, set by the part’s trigger property.

Pins to leave alone

An Uno sketch’s source builds for the R4, but a compiled Uno program will not run on it: different chip. The R4’s pins source less current than an Uno’s, about 8 mA each, so do not drive a relay coil or a motor straight from one.

The sketch

The working code for the Arduino Uno R4

Library: none, the sketch drives IN with digitalWrite(). This is the sketch the circuit above runs.

Relay on Arduino Uno R4 pin 2
const int RELAY_PIN = 2;   // IN, pin 2

void setup() {
  Serial.begin(9600);
  pinMode(RELAY_PIN, OUTPUT);
  digitalWrite(RELAY_PIN, LOW);      // released at start
}

void loop() {
  digitalWrite(RELAY_PIN, HIGH);     // pull in: COM to NO
  Serial.println("Relay on");
  delay(1000);
  digitalWrite(RELAY_PIN, LOW);      // release: COM back to NC
  Serial.println("Relay off");
  delay(1000);
}
Output

What you should see

The relay clicks closed and open. The serial monitor, at 9600 baud, prints Relay on when the coil is energized and Relay off when it is released.

The switched side, COM, NO and NC, is isolated from the board: wire the load there, never to the board’s pins.

The serial monitor prints this, recorded from the circuit above running for two and a half seconds:

Relay on
Relay off
Relay on
Pitfalls

Common mistakes wiring a relay module to an Arduino Uno R4

Active low modules

Many cheap relay boards switch when IN goes LOW, so the sketch seems inverted and the relay is on at boot. Check the board, and in the editor set the relay’s trigger property to low to match.

Driving a coil straight from a pin

A bare relay coil wants 70 mA or more and kicks back a voltage spike when it releases. On a module the transistor and the flyback diode are already there; a bare relay needs both, and never a direct pin.

Expecting an Uno’s pin current

The R4’s pins are 5 V like an Uno’s, but each one sources only about 8 mA where an Uno’s gives 20. A signal line to the relay’s IN pin is fine; an LED or a coil hung straight off the pin is not.

Build your own relay module project

Open this circuit in the editor, change the wiring or the code, and keep your version in a free account.