Wiring guide

How to wire an SSD1306 OLED to an ESP32

To wire an SSD1306 OLED to an ESP32, connect VCC to 3V3, GND to GND, SDA to GPIO 21 (D21) and SCL to GPIO 22 (D22). The ESP32 is a 3.3 V board, so power the module from 3.3 V and its I2C pull-ups pull SDA and SCL to 3.3 V too. The sketch below uses the Adafruit SSD1306 and Adafruit GFX (Adafruit_SSD1306.h) library. It draws the board name, a box and a counter of the seconds since power-up.

  • 3.3 V logic
  • Library: Adafruit_SSD1306.h
  • 4 wires
ESP32 · SSD1306 OLEDlive0.000 s 0.00x
Click to open it in the editor
The circuit itself, running on the simulator with the sketch below. Press what can be pressed; click anything else to open it in the editor.
Pin to pin

SSD1306 OLED to ESP32 wiring table

Every wire in the circuit above, with the part’s pin names and the board’s own labels. The wire colors are the ones the circuit uses; on a real bench any colors work.

SSD1306 OLED pinESP32 pinWire colorWhy
VCC3V3redThe usual blue module runs from 3.3 V, and its I2C pull-ups then pull to 3.3 V too.
GNDGNDblueCommon ground.
SDAGPIO 21 (D21)violetESP32’s I2C data line, where Wire.begin() puts it.
SCLGPIO 22 (D22)cyanESP32’s I2C clock line.
Voltage

Power and logic levels for SSD1306 OLED and ESP32

Logic level

The ESP32’s GPIO pins are 3.3 V logic and are not 5 V tolerant. Nothing wired to a pin may go above 3.3 V.

Supply

The SSD1306 OLED takes 3.3 V from 3V3. That pin is the ESP32’s own regulated 3.3 V output.

This pair

On an ESP32 DevKit, Wire.begin() with no arguments puts SDA on GPIO 21 and SCL on GPIO 22, labeled D21 and D22. The display answers at address 0x3C, the address almost every 0.96 inch module ships with.

Pins to leave alone

GPIO 34, 35, 36 (VP) and 39 (VN) are input only: they cannot drive a pin or take an internal pull-up. GPIO 0, 2, 5, 12 and 15 are strapping pins, read at power-on, and GPIO 6 to 11 are the flash chip.

The sketch

The working code for the ESP32

Library: Adafruit SSD1306 and Adafruit GFX (Adafruit_SSD1306.h). This is the sketch the circuit above runs.

SSD1306 on ESP32 I2C
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>

// 128 x 64 pixels, on the I2C bus: SDA GPIO 21 (D21), SCL GPIO 22 (D22)
Adafruit_SSD1306 display(128, 64, &Wire, -1);

void setup() {
  Serial.begin(115200);
  if (!display.begin(SSD1306_SWITCHCAPVCC, 0x3C)) {
    Serial.println("No SSD1306 at 0x3C");
    for (;;) {}
  }
  display.clearDisplay();
  display.setTextColor(SSD1306_WHITE);
  display.setTextSize(2);
  display.setCursor(0, 0);
  display.println("ESP32");
  display.setTextSize(1);
  display.println("SSD1306 OLED");
  display.drawRect(0, 40, 128, 24, SSD1306_WHITE);
  display.display();
  Serial.println("OLED ready");
}

void loop() {
  // A counter in the box, redrawn twice a second.
  display.fillRect(2, 42, 124, 20, SSD1306_BLACK);
  display.setCursor(8, 48);
  display.print("Up for ");
  display.print(millis() / 1000);
  display.print(" s");
  display.display();
  delay(500);
}
Output

What you should see

The panel shows ESP32 in large letters, SSD1306 OLED below it, and a box with Up for followed by a number of seconds that counts up. The serial monitor, at 115200 baud, prints OLED ready once.

If the monitor prints No SSD1306 at 0x3C instead, nothing answered on the bus: check SDA and SCL first. The font in the simulator has capitals only, so lower case prints as capitals.

The serial monitor prints this, recorded from the circuit above running:

OLED ready
Pitfalls

Common mistakes wiring an SSD1306 OLED to an ESP32

Forgetting display()

Every call before display() only changes the copy in RAM. A sketch that draws and never calls display() leaves the screen black, and that is the most common "my OLED does not work" there is.

Expecting the bus on the old ESP8266 pins

Tutorials written for the ESP8266 put I2C on GPIO 4 and 5. On an ESP32 DevKit Wire.begin() uses GPIO 21 (D21) and GPIO 22 (D22). Either wire it there or call Wire.begin(sda, scl) before display.begin() with the pins you used.

Mixing up the 128x32 module

The 128 by 32 OLED uses the same chip and the same address, but the constructor needs 128, 32. Built for 64 rows, everything is drawn half off the panel.

Build your own SSD1306 OLED project

Open this circuit in the editor, change the wiring or the code, and keep your version in a free account.