DHT22 zamanlaması
Read a DHT22 with no library: the start pulse, the sensor’s answer, forty bits told apart by how long they stay high, the checksum and the sign bit, with every pulse width printed.
Simülatörde açHavayı izleyen sensörler, Uno üzerinde kabloya yakın okumayla: DS18B20 ve DHT22 zamanlaması, elle SHT31 ve AHT20, BME680 basınç ve gaz, SGP30, SCD41 ile gerçek CO2 ve PMS5003 ile partiküller, sonra bir uzay istasyonu kabin hava monitörü.
7 dersin 0'ı tamamlandı
4 bölümde 7 ders, simüle edilmiş bir Arduino Uno R3 üzerinde yaklaşık 7 saat. Ücretsiz, tarayıcında, her adım simülatör tarafından denetlenir.
Read a DHT22 with no library: the start pulse, the sensor’s answer, forty bits told apart by how long they stay high, the checksum and the sign bit, with every pulse width printed.
Simülatörde açAir pressure into altitude with a BME680, then the two metal-oxide gas sensors: the BME680’s hot plate against a clean-air baseline, and the SGP30’s TVOC and CO2eq, its warm-up and its humidity compensation.
Simülatörde açA laser particle counter read byte by byte: the 32-byte frame and its checksum, PM1.0, PM2.5 and PM10, a running average graded on the US AQI bands and the WHO guideline, and sleep on the SET pin.
Simülatörde açHer ders, bir önceki bitince açılır ve her bölüm bir projeyle biter.
Temperature and humidity on a single data pin, with the timing done by hand.
One room read two ways: two DS18B20 probes sharing one wire, each with its own 64-bit address, and a thermistor on an analog pin. ROM codes, CRCs, resolution against conversion time, and when each part is the right one.
0 / 6 adım
Read a DHT22 with no library: the start pulse, the sensor’s answer, forty bits told apart by how long they stay high, the checksum and the sign bit, with every pulse width printed.
0 / 6 adım
Humidity, pressure and gas sensors read from their datasheets with plain Wire calls.
Two modern humidity sensors side by side, read with plain Wire calls: the bus scan, the commands, the raw words, Sensirion’s CRC-8, the AHT20’s packed 20-bit numbers, and a dew point from the Magnus formula.
0 / 6 adım
Air pressure into altitude with a BME680, then the two metal-oxide gas sensors: the BME680’s hot plate against a clean-air baseline, and the SGP30’s TVOC and CO2eq, its warm-up and its humidity compensation.
0 / 7 adım
Real CO2 and fine particles, and the health numbers that grade them.
A photoacoustic NDIR sensor that measures CO2 itself, every five seconds: the data-ready flag, the ventilation bands from fresh air to the workplace limit, a warning lamp, and why every CO2 sensor needs calibrating.
0 / 6 adım
A laser particle counter read byte by byte: the 32-byte frame and its checksum, PM1.0, PM2.5 and PM10, a running average graded on the US AQI bands and the WHO guideline, and sleep on the SET pin.
0 / 6 adım
Tüm sensörler tek veriyolunda, bir uzay istasyonu modülünü nefes alabilir tutuyor.
Put it all together: CO2 from an SCD41, temperature and humidity from an SHT31 and particles from a PMS5003, each graded OK, WARN or ALARM, the worst on an LCD, a red lamp and a buzzer, for a module with no window to open.
0 / 7 adım
Tüm dersleri bitirip tüm bölüm sınavlarını geçtiğinde Mokxi, kendi sayfasında doğrulanan, adının yazdığı bir sertifika düzenler.
Tamamlama Sertifikası
Bu belge şu kişiyi sertifikalandırır:
Adın
kursu başarıyla tamamlamıştır
Hava, ısı ve nem sensörleri
Covering One wire, one pin, On the I2C bus, What you breathe and Boss: the cabin.
7 ders · yaklaşık 7 saat çalışma
Kursu bitir ve adının yazdığı, QR kodlu ve LinkedIn için bağlantılı, doğrulanabilir bir sertifika kazan. Sertifikalar Pro ile gelir ve 7 günlük deneme ücretsizdir.
Tüm 7 ders, sırayla, her biri kapsadığı konularla. Herhangi biri düzenleyicide hemen açılır.
Her ders, hiçbir şey satın almadan simülatörde çalışır. Gerçeğini istediğinde, bu kitlerde gerekli parçalar var.
Sahip olduğun başlangıç kitini seç ve kılavuzundaki tüm dersleri aynı parçalarla, aynı pinlerde çalıştır.
Tüm kitleri görEvet. Hava, ısı ve nem sensörleri derslerinin tamamı ücretsizdir ve tarayıcında çalışır; başlamadan önce kurman ya da alman gereken bir şey yoktur.
Hayır. Her ders, parçaları tuval üzerinde olan simüle edilmiş bir Arduino Uno R3'te çalışır ve simülatör her adımı ilerledikçe kontrol eder. Gerçekten kurmak istediğinde, aynı kablolama ve kod gerçek bir kartta çalışır.
Yaklaşık 7 saat: 4 bölümde 7 ders, her biri birkaç kısa adımdan oluşur. İlerlemen kaydedilir, yani herhangi bir dersten sonra durup kaldığın yerden devam edebilirsin.
Her bölüm bunları bir araya getiren bir projeyle bitiyor: DHT22 zamanlaması, BME680 ve SGP30: basınç ve gaz ve PMS5003 ile Parçacıklar.
"DS18B20 vs the thermistor" ile başlar ve her ders bir öncekinin üzerine inşa edilir. Devrelere yeni misin? Sıfırdan başlayan kurs Elektronik temelleri.