Semua jalur

Sensor udara, panas dan kelembapan

Sensor-sensor yang mengawasi udara, dibaca dekat dengan kabel di Uno: timing DS18B20 dan DHT22, SHT31 dan AHT20 dengan tangan, tekanan dan gas BME680, SGP30, CO2 sungguhan dengan SCD41 dan partikel dengan PMS5003, lalu monitor udara kabin stasiun luar angkasa.

Arduino Uno R3Gratis7 pelajaran7 h4 bab2.399 XPRekayasa embedded · Menengah+150 XP

0 dari 7 selesai

Apa yang akan kamu rakit

3 proyek, dibangun langkah demi langkah

7 pelajaran dalam 4 bab, sekitar 7 jam di Arduino Uno R3 simulasi. Gratis, di browser kamu, setiap langkah diperiksa oleh simulator.

Proyek bab 1

Pewaktuan DHT22

Read a DHT22 with no library: the start pulse, the sensor’s answer, forty bits told apart by how long they stay high, the checksum and the sign bit, with every pulse width printed.

Buka di simulator
Proyek Bab 2

BME680 and SGP30: pressure and gas

Air pressure into altitude with a BME680, then the two metal-oxide gas sensors: the BME680’s hot plate against a clean-air baseline, and the SGP30’s TVOC and CO2eq, its warm-up and its humidity compensation.

Buka di simulator
Proyek bab 3

Particles with a PMS5003

A laser particle counter read byte by byte: the 32-byte frame and its checksum, PM1.0, PM2.5 and PM10, a running average graded on the US AQI bands and the WHO guideline, and sleep on the SET pin.

Buka di simulator
Peta

Bab demi bab

Setiap pelajaran terbuka setelah pelajaran sebelumnya selesai, dan setiap bab ditutup dengan sebuah proyek.

Bab 1

Satu kabel, satu pin

Temperature and humidity on a single data pin, with the timing done by hand.

  1. Buka236 XP

    DS18B20 vs termistor

    One room read two ways: two DS18B20 probes sharing one wire, each with its own 64-bit address, and a thermistor on an analog pin. ROM codes, CRCs, resolution against conversion time, and when each part is the right one.

    0 dari 6 langkah

  2. ProyekTerkunci472 XP

    Pewaktuan DHT22

    Read a DHT22 with no library: the start pulse, the sensor’s answer, forty bits told apart by how long they stay high, the checksum and the sign bit, with every pulse width printed.

    0 dari 6 langkah

4 pertanyaan, dinilai sambil mengerjakan.
Bab 2

On the I2C bus

Humidity, pressure and gas sensors read from their datasheets with plain Wire calls.

  1. Terkunci236 XP

    SHT31 and AHT20 on one bus

    Two modern humidity sensors side by side, read with plain Wire calls: the bus scan, the commands, the raw words, Sensirion’s CRC-8, the AHT20’s packed 20-bit numbers, and a dew point from the Magnus formula.

    0 dari 6 langkah

  2. ProyekTerkunci498 XP

    BME680 and SGP30: pressure and gas

    Air pressure into altitude with a BME680, then the two metal-oxide gas sensors: the BME680’s hot plate against a clean-air baseline, and the SGP30’s TVOC and CO2eq, its warm-up and its humidity compensation.

    0 dari 7 langkah

5 pertanyaan, dinilai sambil mengerjakan.
Bab 3

What you breathe

Real CO2 and fine particles, and the health numbers that grade them.

  1. Terkunci218 XP

    Real CO2 with an SCD41

    A photoacoustic NDIR sensor that measures CO2 itself, every five seconds: the data-ready flag, the ventilation bands from fresh air to the workplace limit, a warning lamp, and why every CO2 sensor needs calibrating.

    0 dari 6 langkah

  2. ProyekTerkunci472 XP

    Particles with a PMS5003

    A laser particle counter read byte by byte: the 32-byte frame and its checksum, PM1.0, PM2.5 and PM10, a running average graded on the US AQI bands and the WHO guideline, and sleep on the SET pin.

    0 dari 6 langkah

5 pertanyaan, dinilai sambil mengerjakan.
Bab 4

Boss: kabin

Semua sensor di satu bus, menjaga modul stasiun luar angkasa tetap layak dihuni.

  1. Terkunci267 XP

    Boss: a space station cabin air monitor

    Put it all together: CO2 from an SCD41, temperature and humidity from an SHT31 and particles from a PMS5003, each graded OK, WARN or ALARM, the worst on an LCD, a red lamp and a buzzer, for a module with no window to open.

    0 dari 7 langkah

3 pertanyaan, dinilai selagi mengerjakan.
Sertifikat

Sertifikat saat kamu menyelesaikan

Selesaikan semua pelajaran dan lulus semua kuis bab, lalu Mokxi menerbitkan sertifikat dengan namamu, terverifikasi di halamannya sendiri.

No. SertifikatMXC0-URSE-0001

Sertifikat Penyelesaian

Ini untuk menyatakan bahwa

Nama Kamu

telah berhasil menyelesaikan kursus

Sensor udara, panas dan kelembapan

Covering One wire, one pin, On the I2C bus, What you breathe and Boss: the cabin.

7 pelajaran · sekitar 7 jam belajar

DaneDane, Pendiri, MokxiDiterbitkan 17 November 2026
Verifikasi sertifikat inimokxi.com/cert/MXC0URSE0001
Sertifikat

Raih sertifikatmu

  • Namamu dan ID unikDicetak pada sertifikat mode lanskap yang jadi milikmu.
  • Diverifikasi oleh MokxiKode QR dan halaman publik yang bisa dicek siapa pun.
  • Tambahkan ke LinkedInSatu klik mengisi formulir sertifikasi LinkedIn.
  • Unduh sebagai PDFCetak atau lampirkan ke CV atau lamaranmu.

Selesaikan kursusnya dan raih sertifikat terverifikasi atas namamu, lengkap dengan kode QR dan link untuk LinkedIn. Sertifikat tersedia di paket Pro, dan uji coba 7 hari gratis.

Silabus

Semua pelajaran dalam kursus

Semua 7 pelajaran, berurutan, masing-masing dengan cakupannya. Semuanya langsung terbuka di editor.

Bab 1

Satu kabel, satu pin

  1. DS18B20 vs termistorOne room read two ways: two DS18B20 probes sharing one wire, each with its own 64-bit address, and a thermistor on an analog pin. ROM codes, CRCs, resolution against conversion time, and when each part is the right one.
  2. Pewaktuan DHT22Read a DHT22 with no library: the start pulse, the sensor’s answer, forty bits told apart by how long they stay high, the checksum and the sign bit, with every pulse width printed.
Bab 2

On the I2C bus

  1. SHT31 and AHT20 on one busTwo modern humidity sensors side by side, read with plain Wire calls: the bus scan, the commands, the raw words, Sensirion’s CRC-8, the AHT20’s packed 20-bit numbers, and a dew point from the Magnus formula.
  2. BME680 and SGP30: pressure and gasAir pressure into altitude with a BME680, then the two metal-oxide gas sensors: the BME680’s hot plate against a clean-air baseline, and the SGP30’s TVOC and CO2eq, its warm-up and its humidity compensation.
Bab 3

What you breathe

  1. Real CO2 with an SCD41A photoacoustic NDIR sensor that measures CO2 itself, every five seconds: the data-ready flag, the ventilation bands from fresh air to the workplace limit, a warning lamp, and why every CO2 sensor needs calibrating.
  2. Particles with a PMS5003A laser particle counter read byte by byte: the 32-byte frame and its checksum, PM1.0, PM2.5 and PM10, a running average graded on the US AQI bands and the WHO guideline, and sleep on the SET pin.
Bab 4

Boss: kabin

  1. Boss: a space station cabin air monitorPut it all together: CO2 from an SCD41, temperature and humidity from an SHT31 and particles from a PMS5003, each graded OK, WARN or ALARM, the worst on an LCD, a red lamp and a buzzer, for a module with no window to open.
Kit

Rangkai juga di meja kerja kamu

Setiap pelajaran jalan di simulator tanpa perlu membeli apa pun. Kalau kamu mau yang asli, kit berikut punya komponennya.

Sudah punya kit?

Cari kit kamu

Pilih starter kit yang kamu punya dan jalankan setiap pelajaran di manualnya dengan komponen yang sama di pin yang sama.

Lihat semua kit
Pertanyaan

Tentang Sensor udara, panas dan kelembapan

Is Air, heat and humidity sensors free?

Ya. Semua 7 pelajaran Sensor udara, panas dan kelembapan gratis dan berjalan di browser-mu, tanpa perlu memasang apa pun dan tanpa perlu membeli komponen sebelum memulai.

Apakah aku butuh Arduino Uno R3 sungguhan?

Tidak. Setiap pelajaran berjalan di Arduino Uno R3 simulasi dengan komponennya di kanvas, dan simulator memeriksa tiap langkah saat kamu melakukannya. Saat kamu ingin merakitnya sungguhan, kabel dan kode yang sama bekerja di board asli.

Berapa lama waktu yang dibutuhkan untuk Sensor udara, panas dan kelembapan?

Sekitar 7 jam: 7 pelajaran dalam 4 bab, tiap bab terdiri dari beberapa langkah pendek. Progres-mu tersimpan, jadi kamu bisa berhenti setelah pelajaran mana pun dan lanjut dari tempat kamu tinggalkan.

Apa yang akan aku buat?

Setiap bab diakhiri dengan proyek yang merangkai semuanya: timing DHT22, BME680 dan SGP30: tekanan dan gas, serta Partikel dengan PMS5003.

Di mana aku mulai?

Dengan "DS18B20 vs termistor", dan setiap pelajaran dibangun di atas pelajaran sebelumnya. Baru mengenal rangkaian? Dasar-dasar elektronika adalah kursus yang dimulai dari nol.