جميع المسارات

حساسات الهواء والحرارة والرطوبة

الحساسات التي تراقب الهواء، تُقرأ من قِبل السلك على Uno: توقيت DS18B20 وDHT22، وSHT31 وAHT20 يدويًا، وضغط BME680 وغازاته، وSGP30، وقياس CO2 حقيقي باستخدام SCD41 والجسيمات باستخدام PMS5003، ثم جهاز مراقبة هواء مقصورة محطة فضائية.

Arduino Uno R3مجاني7 دروس7 h4 فصول2,399 XPهندسة الأنظمة المدمجة · متوسط+150 XP

أُنجز 0 من 7

ابدأ الدورة مجانًاDS18B20 مقابل المقاومة الحراريةخطة الدروس للمعلّمين
ماذا ستبني

3 مشاريع، تُبنى خطوة بخطوة

7 دروس في 4 فصول، نحو 7 ساعات على محاكاة لوحة Arduino Uno R3. مجانًا، في متصفحك، وكل خطوة يفحصها المحاكي.

مشروع الفصل 1

توقيت DHT22

Read a DHT22 with no library: the start pulse, the sensor’s answer, forty bits told apart by how long they stay high, the checksum and the sign bit, with every pulse width printed.

افتحها في المحاكي
مشروع الفصل الثاني

BME680 and SGP30: pressure and gas

Air pressure into altitude with a BME680, then the two metal-oxide gas sensors: the BME680’s hot plate against a clean-air baseline, and the SGP30’s TVOC and CO2eq, its warm-up and its humidity compensation.

افتحها في المحاكي
مشروع الفصل 3

Particles with a PMS5003

A laser particle counter read byte by byte: the 32-byte frame and its checksum, PM1.0, PM2.5 and PM10, a running average graded on the US AQI bands and the WHO guideline, and sleep on the SET pin.

افتحها في المحاكي
الخريطة

فصلًا فصلًا

يفتح كل درس عند انتهاء الذي قبله، وينتهي كل فصل بمشروع.

الفصل 1

سلك واحد، طرف واحد

Temperature and humidity on a single data pin, with the timing done by hand.

  1. فتح236 XP

    DS18B20 مقابل المقاومة الحرارية

    One room read two ways: two DS18B20 probes sharing one wire, each with its own 64-bit address, and a thermistor on an analog pin. ROM codes, CRCs, resolution against conversion time, and when each part is the right one.

    0 من 6 خطوات

  2. مشروعمقفل472 XP

    توقيت DHT22

    Read a DHT22 with no library: the start pulse, the sensor’s answer, forty bits told apart by how long they stay high, the checksum and the sign bit, with every pulse width printed.

    0 من 6 خطوات

4 أسئلة، تُصحَّح أثناء الإجابة.
الفصل 2

On the I2C bus

Humidity, pressure and gas sensors read from their datasheets with plain Wire calls.

  1. مقفل236 XP

    SHT31 and AHT20 on one bus

    Two modern humidity sensors side by side, read with plain Wire calls: the bus scan, the commands, the raw words, Sensirion’s CRC-8, the AHT20’s packed 20-bit numbers, and a dew point from the Magnus formula.

    0 من 6 خطوات

  2. مشروعمقفل498 XP

    BME680 and SGP30: pressure and gas

    Air pressure into altitude with a BME680, then the two metal-oxide gas sensors: the BME680’s hot plate against a clean-air baseline, and the SGP30’s TVOC and CO2eq, its warm-up and its humidity compensation.

    0 من 7 خطوات

5 أسئلة، تُصحَّح أثناء الإجابة.
الفصل 3

What you breathe

Real CO2 and fine particles, and the health numbers that grade them.

  1. مقفل218 XP

    Real CO2 with an SCD41

    A photoacoustic NDIR sensor that measures CO2 itself, every five seconds: the data-ready flag, the ventilation bands from fresh air to the workplace limit, a warning lamp, and why every CO2 sensor needs calibrating.

    0 من 6 خطوات

  2. مشروعمقفل472 XP

    Particles with a PMS5003

    A laser particle counter read byte by byte: the 32-byte frame and its checksum, PM1.0, PM2.5 and PM10, a running average graded on the US AQI bands and the WHO guideline, and sleep on the SET pin.

    0 من 6 خطوات

5 أسئلة، تُصحَّح أثناء الإجابة.
الفصل 4

التحدي: المقصورة

كل الحساسات على ناقل واحد، للحفاظ على هواء صالح للتنفس في وحدة محطة فضاء.

  1. مقفل267 XP

    Boss: a space station cabin air monitor

    Put it all together: CO2 from an SCD41, temperature and humidity from an SHT31 and particles from a PMS5003, each graded OK, WARN or ALARM, the worst on an LCD, a red lamp and a buzzer, for a module with no window to open.

    0 من 7 خطوات

3 أسئلة، تُصحَّح أثناء تقدّمك.
شهادة

شهادة عند إكمالك الدورة

أكمل كل الدروس واجتز اختبار كل فصل، وستمنحك Mokxi شهادة تحمل اسمك، موثّقة في صفحتها الخاصة.

رقم الشهادةMXC0-URSE-0001

شهادة إتمام

تشهد هذه الشهادة بأن

اسمك

أكمل بنجاح الدورة

حساسات الهواء والحرارة والرطوبة

Covering One wire, one pin, On the I2C bus, What you breathe and Boss: the cabin.

7 دروس · حوالي 7 ساعات من الدراسة

DaneDane، مؤسس Mokxiصدرت في 17 نوفمبر 2026
تحقّق من هذه الشهادةmokxi.com/cert/MXC0URSE0001
شهادة

احصل على شهادتك

  • اسمك ورقم فريدمطبوعان على شهادة أفقية تبقى لك.
  • موثّقة من Mokxiرمز QR وصفحة عامة يمكن لأي شخص التحقق منها.
  • أضفها إلى LinkedInنقرة واحدة تملأ نموذج الشهادات في LinkedIn.
  • نزّلها بصيغة PDFاطبعها أو أرفقها بسيرة ذاتية أو طلب تقديم.

أكمل الدورة واحصل على شهادة قابلة للتحقق تحمل اسمك ورمز QR ورابطًا لـ LinkedIn. الشهادات تأتي مع باقة Pro، والتجربة المجانية 7 أيام.

المنهج

كل درس في الدورة

كل الدروس السبعة، بالترتيب، مع ما يغطيه كل درس. أي منها يفتح في المحرر مباشرة.

الفصل 1

سلك واحد، طرف واحد

  1. DS18B20 مقابل المقاومة الحراريةOne room read two ways: two DS18B20 probes sharing one wire, each with its own 64-bit address, and a thermistor on an analog pin. ROM codes, CRCs, resolution against conversion time, and when each part is the right one.
  2. توقيت DHT22Read a DHT22 with no library: the start pulse, the sensor’s answer, forty bits told apart by how long they stay high, the checksum and the sign bit, with every pulse width printed.
الفصل 2

On the I2C bus

  1. SHT31 and AHT20 on one busTwo modern humidity sensors side by side, read with plain Wire calls: the bus scan, the commands, the raw words, Sensirion’s CRC-8, the AHT20’s packed 20-bit numbers, and a dew point from the Magnus formula.
  2. BME680 and SGP30: pressure and gasAir pressure into altitude with a BME680, then the two metal-oxide gas sensors: the BME680’s hot plate against a clean-air baseline, and the SGP30’s TVOC and CO2eq, its warm-up and its humidity compensation.
الفصل 3

What you breathe

  1. Real CO2 with an SCD41A photoacoustic NDIR sensor that measures CO2 itself, every five seconds: the data-ready flag, the ventilation bands from fresh air to the workplace limit, a warning lamp, and why every CO2 sensor needs calibrating.
  2. Particles with a PMS5003A laser particle counter read byte by byte: the 32-byte frame and its checksum, PM1.0, PM2.5 and PM10, a running average graded on the US AQI bands and the WHO guideline, and sleep on the SET pin.
الفصل 4

التحدي: المقصورة

  1. Boss: a space station cabin air monitorPut it all together: CO2 from an SCD41, temperature and humidity from an SHT31 and particles from a PMS5003, each graded OK, WARN or ALARM, the worst on an LCD, a red lamp and a buzzer, for a module with no window to open.
المجموعات

ابنِها على منضدتك أيضًا

كل درس يعمل في المحاكي دون شراء أي شيء. وإذا أردت التجربة الحقيقية، فهذه المجموعات تحتوي على القطع اللازمة.

لديك مجموعة بالفعل؟

اعثر على مجموعتك

اختر مجموعة البداية التي تملكها وشغّل كل درس في كتيّبها بنفس القطع وعلى نفس الأطراف.

شاهد كل مجموعة
الأسئلة

عن حساسات الهواء والحرارة والرطوبة

Is Air, heat and humidity sensors free?

نعم. كل الدروس السبعة في حساسات الهواء والحرارة والرطوبة مجانية وتعمل في متصفحك، بلا شيء لتثبّته وبلا قطع لتشتريها قبل أن تبدأ.

هل أحتاج إلى Arduino Uno R3 حقيقية؟

لا. كل درس يعمل على Arduino Uno R3 محاكاة مع قطعها على مساحة العمل، والمحاكي يتحقق من كل خطوة أثناء تقدّمك. وعندما تريد البناء الحقيقي، ستعمل التوصيلات والكود نفسها على لوحة حقيقية.

كم من الوقت تستغرق دورة حساسات الهواء والحرارة والرطوبة؟

حوالي 7 ساعات: 7 دروس في 4 فصول، كل درس بضع خطوات قصيرة. تُحفَظ نقاط تقدّمك، فيمكنك التوقف بعد أي درس والمتابعة من حيث توقفت.

ماذا سأبني؟

تنتهي كل فصل بمشروع يجمع كل ما فيه: توقيت DHT22، وBME680 وSGP30: الضغط والغاز، والجزيئات مع PMS5003.

من أين أبدأ؟

مع درس «DS18B20 مقابل المقاومة الحرارية»، وكل درس يبني على ما قبله. جديد على الدوائر؟ أساسيات الإلكترونيات هي الدورة التي تبدأ من الصفر.