Todas las rutas

Sensores de aire, calor y humedad

Los sensores que vigilan el aire, leídos a bajo nivel en el Uno: temporización del DS18B20 y el DHT22, SHT31 y AHT20 a mano, presión y gas con el BME680, SGP30, CO2 real con un SCD41 y partículas con un PMS5003, luego un monitor de aire de cabina de estación espacial.

Arduino Uno R3Gratis7 lecciones7 h4 capítulos2,399 XPIngeniería de embebidos · Intermedio+150 XP

0 de 7 completadas

Lo que vas a construir

3 proyectos, construidos paso a paso

7 lecciones en 4 capítulos, unas 7 horas en un Arduino Uno R3 simulado. Gratis, en tu navegador, cada paso verificado por el simulador.

Proyecto del capítulo 1

Temporización del DHT22

Read a DHT22 with no library: the start pulse, the sensor’s answer, forty bits told apart by how long they stay high, the checksum and the sign bit, with every pulse width printed.

Ábrelo en el simulador
Proyecto del capítulo 2

BME680 and SGP30: pressure and gas

Air pressure into altitude with a BME680, then the two metal-oxide gas sensors: the BME680’s hot plate against a clean-air baseline, and the SGP30’s TVOC and CO2eq, its warm-up and its humidity compensation.

Ábrelo en el simulador
Proyecto del capítulo 3

Particles with a PMS5003

A laser particle counter read byte by byte: the 32-byte frame and its checksum, PM1.0, PM2.5 and PM10, a running average graded on the US AQI bands and the WHO guideline, and sleep on the SET pin.

Ábrelo en el simulador
El mapa

Capítulo por capítulo

Cada lección se abre cuando termina la anterior, y cada capítulo termina en un proyecto.

Capítulo 1

Un cable, un pin

Temperature and humidity on a single data pin, with the timing done by hand.

  1. Abrir236 XP

    DS18B20 contra la termistor

    One room read two ways: two DS18B20 probes sharing one wire, each with its own 64-bit address, and a thermistor on an analog pin. ROM codes, CRCs, resolution against conversion time, and when each part is the right one.

    0 de 6 pasos

  2. ProyectoBloqueado472 XP

    Temporización del DHT22

    Read a DHT22 with no library: the start pulse, the sensor’s answer, forty bits told apart by how long they stay high, the checksum and the sign bit, with every pulse width printed.

    0 de 6 pasos

4 preguntas, calificadas conforme avanzas.
Capítulo 2

On the I2C bus

Humidity, pressure and gas sensors read from their datasheets with plain Wire calls.

  1. Bloqueado236 XP

    SHT31 and AHT20 on one bus

    Two modern humidity sensors side by side, read with plain Wire calls: the bus scan, the commands, the raw words, Sensirion’s CRC-8, the AHT20’s packed 20-bit numbers, and a dew point from the Magnus formula.

    0 de 6 pasos

  2. ProyectoBloqueado498 XP

    BME680 and SGP30: pressure and gas

    Air pressure into altitude with a BME680, then the two metal-oxide gas sensors: the BME680’s hot plate against a clean-air baseline, and the SGP30’s TVOC and CO2eq, its warm-up and its humidity compensation.

    0 de 7 pasos

5 preguntas, calificadas conforme avanzas.
Capítulo 3

What you breathe

Real CO2 and fine particles, and the health numbers that grade them.

  1. Bloqueado218 XP

    Real CO2 with an SCD41

    A photoacoustic NDIR sensor that measures CO2 itself, every five seconds: the data-ready flag, the ventilation bands from fresh air to the workplace limit, a warning lamp, and why every CO2 sensor needs calibrating.

    0 de 6 pasos

  2. ProyectoBloqueado472 XP

    Particles with a PMS5003

    A laser particle counter read byte by byte: the 32-byte frame and its checksum, PM1.0, PM2.5 and PM10, a running average graded on the US AQI bands and the WHO guideline, and sleep on the SET pin.

    0 de 6 pasos

5 preguntas, calificadas conforme avanzas.
Capítulo 4

Jefe: la cabina

Todos los sensores en un solo bus, manteniendo respirable el módulo de una estación espacial.

  1. Bloqueado267 XP

    Boss: a space station cabin air monitor

    Put it all together: CO2 from an SCD41, temperature and humidity from an SHT31 and particles from a PMS5003, each graded OK, WARN or ALARM, the worst on an LCD, a red lamp and a buzzer, for a module with no window to open.

    0 de 7 pasos

3 preguntas, calificadas al momento.
Certificado

Un certificado al terminar

Termina todas las lecciones y aprueba todos los cuestionarios de capítulo, y Mokxi te emite un certificado con tu nombre, verificado en su propia página.

Certificado n.ºMXC0-URSE-0001

Certificado de Finalización

Se certifica que

Tu Nombre

ha completado con éxito el curso

Sensores de aire, calor y humedad

Covering One wire, one pin, On the I2C bus, What you breathe and Boss: the cabin.

7 lecciones · alrededor de 7 horas de estudio

DaneDane, Fundador, MokxiEmitido el 17 de noviembre de 2026
Verificar este certificadomokxi.com/cert/MXC0URSE0001
Certificado

Gana tu certificado

  • Tu nombre y un ID únicoImpreso en un certificado horizontal que es tuyo para siempre.
  • Verificado por MokxiUn código QR y una página pública con la que cualquiera puede comprobarlo.
  • Agregar a LinkedInUn clic llena el formulario de certificaciones de LinkedIn.
  • Descargar como PDFImprímelo o adjúntalo a un currículum o a una solicitud.

Termina el curso y gana un certificado verificable con tu nombre, un código QR y un enlace para LinkedIn. Los certificados vienen con Pro, y la prueba gratis de 7 días no te cuesta nada.

Temario

Todas las lecciones del curso

Las 7 lecciones, en orden, cada una con lo que abarca. Cualquiera se abre en el editor de inmediato.

Capítulo 1

Un cable, un pin

  1. DS18B20 contra la termistorOne room read two ways: two DS18B20 probes sharing one wire, each with its own 64-bit address, and a thermistor on an analog pin. ROM codes, CRCs, resolution against conversion time, and when each part is the right one.
  2. Temporización del DHT22Read a DHT22 with no library: the start pulse, the sensor’s answer, forty bits told apart by how long they stay high, the checksum and the sign bit, with every pulse width printed.
Capítulo 2

On the I2C bus

  1. SHT31 and AHT20 on one busTwo modern humidity sensors side by side, read with plain Wire calls: the bus scan, the commands, the raw words, Sensirion’s CRC-8, the AHT20’s packed 20-bit numbers, and a dew point from the Magnus formula.
  2. BME680 and SGP30: pressure and gasAir pressure into altitude with a BME680, then the two metal-oxide gas sensors: the BME680’s hot plate against a clean-air baseline, and the SGP30’s TVOC and CO2eq, its warm-up and its humidity compensation.
Capítulo 3

What you breathe

  1. Real CO2 with an SCD41A photoacoustic NDIR sensor that measures CO2 itself, every five seconds: the data-ready flag, the ventilation bands from fresh air to the workplace limit, a warning lamp, and why every CO2 sensor needs calibrating.
  2. Particles with a PMS5003A laser particle counter read byte by byte: the 32-byte frame and its checksum, PM1.0, PM2.5 and PM10, a running average graded on the US AQI bands and the WHO guideline, and sleep on the SET pin.
Capítulo 4

Jefe: la cabina

  1. Boss: a space station cabin air monitorPut it all together: CO2 from an SCD41, temperature and humidity from an SHT31 and particles from a PMS5003, each graded OK, WARN or ALARM, the worst on an LCD, a red lamp and a buzzer, for a module with no window to open.
Kits

Armélo también en tu banco de trabajo

Cada lección funciona en el simulador sin comprar nada. Cuando quieras lo real, estos kits tienen los componentes.

¿Ya tienes un kit?

Encuentra tu kit

Elige el kit inicial que tienes y ejecuta cada lección de su instructivo con los mismos componentes en los mismos pines.

Ver todos los kits
Preguntas

Acerca de Sensores de aire, calor y humedad

Is Air, heat and humidity sensors free?

Sí. Las 7 lecciones de Sensores de aire, calor y humedad son gratis y corren en tu navegador, sin nada que instalar y sin componentes que comprar antes de empezar.

¿Necesito un Arduino Uno R3 de verdad?

No. Cada lección corre en un Arduino Uno R3 simulado con sus componentes en el lienzo, y el simulador comprueba cada paso sobre la marcha. Cuando quieras construirlo de verdad, el mismo cableado y código funcionan en una placa real.

¿Cuánto dura Sensores de aire, calor y humedad?

Unas 7 horas: 7 lecciones en 4 capítulos, cada uno con unos cuantos pasos cortos. Tu progreso se guarda, así que puedes parar después de cualquier lección y retomar donde lo dejaste.

¿Qué voy a armar?

Cada capítulo termina con un proyecto que une todo: temporización del DHT22, BME680 y SGP30: presión y gases, y partículas con un PMS5003.

¿Por dónde empiezo?

Con "DS18B20 contra la termistencia", y cada lección se construye sobre la anterior. ¿Nuevo en los circuitos? Electrónica básica es el curso que empieza desde cero.