Todos os caminhos

Sensores de ar, calor e umidade

Os sensores que vigiam o ar, lidos perto do fio no Uno: temporização do DS18B20 e do DHT22, SHT31 e AHT20 à mão, pressão e gás no BME680, SGP30, CO2 de verdade com um SCD41 e partículas com um PMS5003, e depois um monitor de ar de cabine de estação espacial.

Arduino Uno R3Grátis7 aulas7 h4 capítulos2.399 XPEngenharia embarcada · Intermediário+150 XP

0 de 7 concluídas

O que você vai montar

3 projetos, construídos passo a passo

7 aulas em 4 capítulos, cerca de 7 horas em um Arduino Uno R3 simulado. Grátis, no seu navegador, cada passo verificado pelo simulador.

Projeto do capítulo 1

Tempo do DHT22

Read a DHT22 with no library: the start pulse, the sensor’s answer, forty bits told apart by how long they stay high, the checksum and the sign bit, with every pulse width printed.

Abrir no simulador
Projeto do capítulo 2

BME680 and SGP30: pressure and gas

Air pressure into altitude with a BME680, then the two metal-oxide gas sensors: the BME680’s hot plate against a clean-air baseline, and the SGP30’s TVOC and CO2eq, its warm-up and its humidity compensation.

Abrir no simulador
Projeto do capítulo 3

Particles with a PMS5003

A laser particle counter read byte by byte: the 32-byte frame and its checksum, PM1.0, PM2.5 and PM10, a running average graded on the US AQI bands and the WHO guideline, and sleep on the SET pin.

Abrir no simulador
O mapa

Capítulo por capítulo

Cada aula abre quando a anterior termina, e cada capítulo acaba num projeto.

Capítulo 1

Um fio, um pino

Temperature and humidity on a single data pin, with the timing done by hand.

  1. Abrir236 XP

    DS18B20 versus o termistor

    One room read two ways: two DS18B20 probes sharing one wire, each with its own 64-bit address, and a thermistor on an analog pin. ROM codes, CRCs, resolution against conversion time, and when each part is the right one.

    0 de 6 passos

  2. ProjetoBloqueado472 XP

    Tempo do DHT22

    Read a DHT22 with no library: the start pulse, the sensor’s answer, forty bits told apart by how long they stay high, the checksum and the sign bit, with every pulse width printed.

    0 de 6 passos

4 perguntas, com nota conforme você responde.
Capítulo 2

On the I2C bus

Humidity, pressure and gas sensors read from their datasheets with plain Wire calls.

  1. Bloqueado236 XP

    SHT31 and AHT20 on one bus

    Two modern humidity sensors side by side, read with plain Wire calls: the bus scan, the commands, the raw words, Sensirion’s CRC-8, the AHT20’s packed 20-bit numbers, and a dew point from the Magnus formula.

    0 de 6 passos

  2. ProjetoBloqueado498 XP

    BME680 and SGP30: pressure and gas

    Air pressure into altitude with a BME680, then the two metal-oxide gas sensors: the BME680’s hot plate against a clean-air baseline, and the SGP30’s TVOC and CO2eq, its warm-up and its humidity compensation.

    0 de 7 passos

5 perguntas, com nota conforme você responde.
Capítulo 3

What you breathe

Real CO2 and fine particles, and the health numbers that grade them.

  1. Bloqueado218 XP

    Real CO2 with an SCD41

    A photoacoustic NDIR sensor that measures CO2 itself, every five seconds: the data-ready flag, the ventilation bands from fresh air to the workplace limit, a warning lamp, and why every CO2 sensor needs calibrating.

    0 de 6 passos

  2. ProjetoBloqueado472 XP

    Particles with a PMS5003

    A laser particle counter read byte by byte: the 32-byte frame and its checksum, PM1.0, PM2.5 and PM10, a running average graded on the US AQI bands and the WHO guideline, and sleep on the SET pin.

    0 de 6 passos

5 perguntas, com nota conforme você responde.
Capítulo 4

Chefe: a cabine

Todos os sensores em um barramento, mantendo um módulo de estação espacial respirável.

  1. Bloqueado267 XP

    Boss: a space station cabin air monitor

    Put it all together: CO2 from an SCD41, temperature and humidity from an SHT31 and particles from a PMS5003, each graded OK, WARN or ALARM, the worst on an LCD, a red lamp and a buzzer, for a module with no window to open.

    0 de 7 passos

3 perguntas, corrigidas conforme você avança.
Certificado

Um certificado ao terminar

Termine todas as aulas e passe nos quizzes de todos os capítulos, e o Mokxi emitirá um certificado com o seu nome, verificado em sua própria página.

Certificado nºMXC0-URSE-0001

Certificado de Conclusão

Certificamos que

Nome do Aluno

concluiu com êxito o curso

Sensores de ar, calor e umidade

Covering One wire, one pin, On the I2C bus, What you breathe and Boss: the cabin.

7 aulas · cerca de 7 horas de estudo

DaneDane, fundador do MokxiEmitido em 17 de novembro de 2026
Verificar este certificadomokxi.com/cert/MXC0URSE0001
Certificado

Ganhe seu certificado

  • Seu nome e um ID únicoImpresso em um certificado em modo paisagem que é seu para guardar.
  • Verificado pelo MokxiUm QR code e uma página pública com a qual qualquer pessoa pode conferir.
  • Adicionar ao LinkedInCom um clique, o formulário de certificação do LinkedIn é preenchido.
  • Baixar em PDFImprima ou anexe a um currículo ou a uma inscrição.

Termine o curso e ganhe um certificado verificável com seu nome, um QR code e um link para o LinkedIn. Os certificados acompanham o Pro, e o teste de 7 dias é grátis.

Programa do curso

Todas as aulas do curso

Todas as 7 aulas, em ordem, cada uma com o que cobre. Qualquer uma delas abre no editor na hora.

Capítulo 1

Um fio, um pino

  1. DS18B20 versus o termistorOne room read two ways: two DS18B20 probes sharing one wire, each with its own 64-bit address, and a thermistor on an analog pin. ROM codes, CRCs, resolution against conversion time, and when each part is the right one.
  2. Tempo do DHT22Read a DHT22 with no library: the start pulse, the sensor’s answer, forty bits told apart by how long they stay high, the checksum and the sign bit, with every pulse width printed.
Capítulo 2

On the I2C bus

  1. SHT31 and AHT20 on one busTwo modern humidity sensors side by side, read with plain Wire calls: the bus scan, the commands, the raw words, Sensirion’s CRC-8, the AHT20’s packed 20-bit numbers, and a dew point from the Magnus formula.
  2. BME680 and SGP30: pressure and gasAir pressure into altitude with a BME680, then the two metal-oxide gas sensors: the BME680’s hot plate against a clean-air baseline, and the SGP30’s TVOC and CO2eq, its warm-up and its humidity compensation.
Capítulo 3

What you breathe

  1. Real CO2 with an SCD41A photoacoustic NDIR sensor that measures CO2 itself, every five seconds: the data-ready flag, the ventilation bands from fresh air to the workplace limit, a warning lamp, and why every CO2 sensor needs calibrating.
  2. Particles with a PMS5003A laser particle counter read byte by byte: the 32-byte frame and its checksum, PM1.0, PM2.5 and PM10, a running average graded on the US AQI bands and the WHO guideline, and sleep on the SET pin.
Capítulo 4

Chefe: a cabine

  1. Boss: a space station cabin air monitorPut it all together: CO2 from an SCD41, temperature and humidity from an SHT31 and particles from a PMS5003, each graded OK, WARN or ALARM, the worst on an LCD, a red lamp and a buzzer, for a module with no window to open.
Kits

Monte também na sua bancada

Cada aula roda no simulador, sem precisar comprar nada. Quando quiser a versão real, esses kits têm os componentes.

Já tem um kit?

Encontre seu kit

Escolha o kit inicial que você tem e rode todas as aulas do manual dele com os mesmos componentes nos mesmos pinos.

Ver todos os kits
Perguntas

Sobre Sensores de ar, calor e umidade

Is Air, heat and humidity sensors free?

Sim. Todas as 7 aulas de Sensores de ar, calor e umidade são grátis e rodam no seu navegador, sem nada para instalar e sem componentes para comprar antes de começar.

Preciso de um Arduino Uno R3 de verdade?

Não. Cada aula roda em um Arduino Uno R3 simulado com seus componentes no canvas, e o simulador verifica cada passo conforme você avança. Quando quiser montar de verdade, a mesma ligação e o mesmo código funcionam em uma placa real.

Quanto tempo leva Sensores de ar, calor e umidade?

Cerca de 7 horas: 7 aulas em 4 capítulos, cada uma com alguns passos curtos. Seu progresso fica salvo, então você pode parar após qualquer aula e continuar de onde parou.

O que eu vou montar?

Cada capítulo termina com um projeto que junta tudo: temporização do DHT22, BME680 e SGP30: pressão e gás e Partículas com um PMS5003.

Por onde eu começo?

Com "DS18B20 versus o termistor", e cada aula se apoia na anterior. Novo em circuitos? Eletrônica básica é o curso que começa do zero.